Nissan Silvia. Instruction — part 81
SMA260A
Checking Disc Brake
NMBR0124
ROTOR
NMBR0124S01
Check condition and thickness.
Unit: mm (in)
Front
Rear
Disc brake type
OPF25VA
CL11H
Standard thickness
30.0 (1.181)
9.0 (0.354)
Minimum thickness
28.0 (1.102)
8.0 (0.315)
SMA922A
CALIPER
NMBR0124S02
Check for leakage.
SMA847B
PAD
NMBR0124S03
Check for wear or damage.
Unit: mm (in)
Front
Rear
Disc brake type
OPF25VA
CL11H
Standard thickness
10.0 (0.394)
9.5 (0.374)
Minimum thickness
2.0 (0.079)
GI
MA
EM
LC
EC
FE
CL
MT
AT
PD
AX
SU
ST
RS
BT
HA
SC
EL
IDX
ON-VEHICLE SERVICE
Checking Disc Brake
BR-7
SBR995
Bleeding Brake System
=NMBR0009
CAUTION:
I
Carefully monitor brake fluid level at master cylinder dur-
ing bleeding operation.
I
If master cylinder is suspected to have air inside, bleed air
from master cylinder first. Refer to “Installation”, “MAS-
TER CYLINDER”, BR-16.
I
Fill reservoir with new brake fluid “DOT 3”. Make sure it is
full at all times while bleeding air out of system.
I
Place a container under master cylinder to avoid spillage
of brake fluid.
I
Turn ignition switch OFF and disconnect ABS actuator
and electric unit connectors or battery ground cable.
I
Bleed air in the following order.
1. Left rear brake
2. Right rear brake
3. Left front brake
4. Right front brake
SBR419C
1.
Connect a transparent vinyl tube to air bleeder valve.
2.
Fully depress brake pedal several times.
3.
With brake pedal depressed, open air bleeder valve to release
air.
4.
Close air bleeder valve.
5.
Release brake pedal slowly.
6.
Repeat steps 2. through 5. until clear brake fluid comes out of
air bleeder valve.
7.
Tighten air bleeder valve.
: 7 - 9 N·m (0.7 - 0.9 kg-m, 61 - 78 in-lb)
ON-VEHICLE SERVICE
Bleeding Brake System
BR-8
Hydraulic Circuit
NMBR0010
SBR990C
SBR992
Removal
NMBR0011
CAUTION:
I
Be careful not to splash brake fluid on painted areas; it
may cause paint damage. If brake fluid is splashed on
painted areas, wash it away with water immediately.
I
All hoses must be free from excessive bending, twisting
and pulling.
1.
Connect vinyl tube to air bleeder valve.
2.
Drain brake fluid from each air bleeder valve by depressing
brake pedal.
3.
Remove flare nut connecting brake tube and hose, then with-
draw lock spring.
4.
Cover openings to prevent entrance of dirt whenever discon-
necting brake line.
GI
MA
EM
LC
EC
FE
CL
MT
AT
PD
AX
SU
ST
RS
BT
HA
SC
EL
IDX
BRAKE HYDRAULIC LINE
Hydraulic Circuit
BR-9
Inspection
NMBR0012
Check brake lines (tubes and hoses) for cracks, deterioration and
other damage. Replace any damaged parts.
SBR686C
Installation
NMBR0013
CAUTION:
I
Refill with new brake fluid “DOT 3”.
I
Never reuse drained brake fluid.
1.
Tighten all flare nuts and connecting bolts.
Flare nut:
: 15 - 17 N·m (1.5 - 1.8 kg-m, 11 - 13 ft-lb)
Connecting bolt:
: 17 - 19 N·m (1.7 - 2.0 kg-m, 12 - 14 ft-lb)
2.
Refill until new brake fluid comes out of each air bleeder valve.
3.
Bleed air. Refer to “Bleeding Brake System”, BR-8.
BRAKE HYDRAULIC LINE
Inspection
BR-10
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст