Nissan Silvia. Instruction — part 223
amount of water. The complete chemical reaction may take as
long as 4 to 5 hours. Remove the valves using a set of large
tweezers after the chemical reaction has stopped. Afterwards,
the valves can be mixed with ordinary scrap metal.
CAUTION:
I
Make sure the resultant (high alkalinity) waste water does
not contact your skin. If the waste water does contact you,
wash the contacted area immediately with large quantities
of water.
I
Check country and local regulations concerning any
chemical treatment or waste water discharge permits.
These may be required to dispose of the resultant (high
alkalinity) waste water.
GI
MA
LC
EC
FE
CL
MT
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
PRECAUTIONS
Special Cautions to Ensure the Safe Disposal of Sodium-filled Exhaust Valves (Cont’d)
EM-5
Special Service Tools
NMEM0003
Tool number
Tool name
Description
ST0501S000
Engine stand assembly
1 ST05011000
Engine stand
2 ST05012000
Base
NT042
Disassembling and assembling
KV10106500
Engine stand shaft
NT028
KV10115300
Engine sub-attachment
NT008
ST10120000
Cylinder head bolt
wrench
NT583
Loosening and tightening cylinder head bolt
a: 13 (0.51) dia.
b: 12 (0.47)
c: 10 (0.39)
Unit: mm (in)
KV10116200
Valve spring compressor
1 KV10115900
Attachment
NT022
Disassembling valve mechanism
KV10115600
Valve oil seal drift
NT603
Installing valve oil seal
Intake (Side A)
a: 20 (0.79) dia.
b: 13 (0.51) dia.
c: 10.3 (0.406) dia.
d: 8 (0.31) dia.
e: 10.7 (0.421)
f: 5 (0.20)
Exhaust (Side B)
a: 20 (0.79) dia.
b: 14.2 (0.559) dia.
c: 11 (0.43) dia.
d: 8 (0.31) dia.
e: 10.7 (0.421) dia.
f: 5 (0.20)
Unit: mm (in)
PREPARATION
Special Service Tools
EM-6
Tool number
Tool name
Description
KV10107902
Valve oil seal puller
NT011
Displacement valve lip seal
KV10115700
Dial gauge stand
NT012
Adjusting shims
EM03470000
Piston ring compressor
NT044
Installing piston assembly into cylinder bore
KV10107400
Piston pin press stand
1 KV10107310
Center shaft
2 ST13040020
Stand
3 ST13040030
Spring
4 KV10107320
Cap
5 ST13040050
Drift
NT013
Disassembling and assembling piston pin
KV10111100
Seal cutter
NT046
Removing oil pan
WS39930000
Tube presser
NT052
Pressing the tube of liquid gasket
KV10112100
Angle wrench
NT014
Tightening bolts for bearing cap, cylinder
head, etc.
GI
MA
LC
EC
FE
CL
MT
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
PREPARATION
Special Service Tools (Cont’d)
EM-7
Tool number
Tool name
Description
ST16610001
Pilot bushing puller
NT045
Removing pilot bushing
KV10117100
Front (heated) oxygen
sensor wrench
NT379
Loosening or tightening front (heated) oxy-
gen sensor
Commercial Service Tools
NMEM0004
Tool name
Description
Spark plug wrench
NT047
Removing and installing spark plug
Valve seat cutter set
NT048
Finishing valve seat dimensions
Piston ring expander
NT030
Removing and installing piston ring
Valve guide drift
NT015
Removing and installing valve guide
Intake
a: 9.5 mm (0.374 in) dia.
b: 5.0 mm (0.197 in) dia.
Exhaust
a: 10.5 mm (0.413 in) dia.
b: 6.0 mm (0.236 in) dia.
Valve guide reamer
NT016
Reaming valve guide 1 or hole for oversize valve
guide 2
Intake
d
1
: 6.0 mm (0.236 in) dia.
d
2
: 10.175 mm (0.4006 in) dia.
Exhaust
d
1
: 7.0 mm (0.276 in) dia.
d
2
: 11.175 mm (0.4400 in) dia.
PREPARATION
Special Service Tools (Cont’d)
EM-8
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст