Nissan Silvia. Instruction — part 49
4
CHECK A/T MODE SWITCH CIRCUIT (With CONSULT-II)
With CONSULT-II
1. Turn ignition switch to “ON” position.
(Do not start engine.)
2. Select “TCM INPUT SIGNALS”.
3. Read out “POWER SHIFT SW”. Make sure the selector lever switch position is indicated properly.
SAT417K
OK or NG
OK (With CONSULT-II)
©
GO TO 7.
OK (Without CONSULT-
II)
©
GO TO 8.
NG
©
GO TO 6.
5
CHECK A/T MODE SWITCH CIRCUIT (Without CONSULT-II)
Without CONSULT-II
1. Turn ignition switch to “ON” position.
(Do not start engine.)
2. Check voltage between TCM harness connector M26 terminal Nos. 43 (GY), 44 (L/B) and ground when A/T mode
switch is “ON” and “OFF”.
SAT120KA
OK or NG
OK (With CONSULT-II)
©
GO TO 7.
OK (Without CONSULT-
II)
©
GO TO 8.
NG
©
GO TO 6.
GI
MA
EM
LC
EC
FE
CL
MT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
TROUBLE DIAGNOSES FOR SYMPTOMS
24. TCM Self-diagnosis Does Not Activate (PNP, Overdrive Control, A/T Check and TP Switches Circuit Checks) (Cont’d)
AT-193
6
DETECT MALFUNCTIONING ITEM
Check the following items:
I
A/T mode switch
a. Check continuity between two terminals.
SAT121KA
I
Harness for short or open between TCM and A/T mode switch (Main harness)
I
Harness of ground circuit for A/T mode switch (Main harness) for short or open
OK or NG
OK (With CONSULT-II)
©
GO TO 7.
OK (Without CONSULT-
II)
©
GO TO 8.
NG
©
Repair or replace damaged parts.
7
CHECK THROTTLE POSITION SWITCH CIRCUIT (With CONSULT-II)
With CONSULT-II
1. Turn ignition switch to “ON” position.
(Do not start engine.)
2. Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT-II.
3. Read out “CLOSED THL/SW” and “W/O THRL/P-SW” depressing and releasing accelerator pedal.
Check the signal of throttle position switch is indicated properly.
MTBL0011
SAT646J
OK or NG
OK
©
GO TO 9.
NG
©
Check the following items:
I
Throttle position switch
Refer to “Component Inspection”, AT-197.
I
Harness for short or open between ignition switch and throttle position switch (Main
harness)
I
Harness for short or open between throttle position switch and TCM (Main harness)
TROUBLE DIAGNOSES FOR SYMPTOMS
24. TCM Self-diagnosis Does Not Activate (PNP, Overdrive Control, A/T Check and TP Switches Circuit Checks) (Cont’d)
AT-194
8
CHECK THROTTLE POSITION SWITCH CIRCUIT (Without CONSULT-II)
Without CONSULT-II
1. Turn ignition switch to “ON” position.
(Do not start engine.)
2. Check voltage between TCM harness connector M25 terminals No. 16 (LG), 17 (R) and ground while depressing, and
releasing accelerator pedal slowly. (after warming up engine)
MTBL0637
SAT526JC
OK or NG
OK
©
GO TO 9.
NG
©
Check the following items:
I
Throttle position switch
Refer to “Component Inspection”, AT-197.
I
Harness for short or open between ignition switch and throttle position switch (Main
harness)
I
Harness for short or open between throttle position switch and TCM (Main harness)
9
CHECK DTC
Perform Diagnostic procedure, AT-190.
OK or NG
OK
©
INSPECTION END
NG
©
1. Perform TCM input/output signal inspection.
2. If NG, recheck TCM pin terminals for damage or loose connection with harness con-
nector.
GI
MA
EM
LC
EC
FE
CL
MT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
TROUBLE DIAGNOSES FOR SYMPTOMS
24. TCM Self-diagnosis Does Not Activate (PNP, Overdrive Control, A/T Check and TP Switches Circuit Checks) (Cont’d)
AT-195
SAT418K
COMPONENT INSPECTION
NMAT0204S04
Overdrive Control Switch
NMAT0204S0401
I
Check continuity.
Terminal
Connector
Switch posi-
tion
Terminal No. (Wire color)
Continuity
B8
OD “ON”
1 (L/B)
2 (B)
No
OD “OFF”
Yes
SAT517GB
SAT843BI
Park/Neutral Position Switch
NMAT0204S0402
1.
Check continuity.
Terminal
Connector
Select lever
position
Terminal No. (Wire color)
Continuity
E22
P, N
1 (B)
2 (BR)
Yes
E23
P
3 (B)
4 (L)
R
3 (B)
5 (G)
N
3 (B)
6 (W)
D
3 (B)
7 (Y)
2
3 (B)
8 (R)
1
3 (B)
9 (OR)
SAT807B
2.
If NG, check again with instruction control linkage disconnected
from instruction shaft of A/T assembly. Refer to step 1.
3.
If OK on step 2, adjust instruction control linkage. Refer to AT-207.
SAT386HF
4.
If NG on step 2, remove PNP switch from A/T and check con-
tinuity of PNP switch terminals. Refer to step 1.
5.
If OK on step 4, adjust PNP switch. Refer to AT-206.
6.
If NG on step 4, replace PNP switch.
TROUBLE DIAGNOSES FOR SYMPTOMS
24. TCM Self-diagnosis Does Not Activate (PNP, Overdrive Control, A/T Check and TP Switches Circuit Checks) (Cont’d)
AT-196
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст