Nissan Terrano r20e. Instruction — part 250
Checks
Once in Diagnostic Mode (and after identifying the last three alarm triggers in case a theft warning system is
equipped on the vehicle), the following inputs can be tested.
USER ACTION
TCU Reaction
COMPONENT TESTED
Driver’s door opened from closed
(all other doors closed)
Hazards flash once
Driver’s door open signal
Passenger or rear door opened from closed
(all other doors closed)
Hazards flash once
Door open signal for opened door
Driver’s door locked from unlocked
Hazards flash once
Driver’s door status signal
Passenger door locked from unlocked
Hazards flash once
Assist door status signal
Rear doors locked from unlocked
(with ultrasonic model)
Hazards flash once
Rear doors status signal
Ultrasonics cancel switch is pressed
(with ultrasonic model)
Hazards flash once
U/S cancel signal
Trunk or back door is opened from closed
Hazards flash once
Trunk open signal
Hood is opened from closed
(with ultrasonic model)
Hazards flash once
Hood open signal
Hazard switch is pressed from off
Hazards flash once
Hazard switch signal
Turn signal switch is moved to left from off
Hazards flash once
Left turn signal
Turn signal switch is moved to right from off
Hazards flash once
Right turn signal
Key turned to lock position in door
Hazards flash once *
Key cylinder lock switch signal
Lighting switch turned 1st position or 2nd
position from off
Hazards flash once
Tail lamp signal
Key put in ignition cylinder from out
Hazards flash once
Key in detect signal
Central unlock switch is pressed
Hazards flash once
Central unlock/Trunk release signal
*) Hazards may flash a second time because of Driver’s door status signal change. The min. delay time between flash actions is
100 ms.
In case the system does not operate as described above, check the concerned circuit for open or short.
After completion, the Diagnostic Mode can be switched off by pressing the rear defogger switch or by turning
the ignition to “ON”. The hazard lamp will flash at 3 Hz for 3 seconds to confirm that Diagnostic Mode has
been switched off.
TIME CONTROL UNIT (TCU)
Trouble Diagnosis (Cont’d)
EL-183
Schematic
YEL168D
TIME CONTROL UNIT (TCU)
EL-184
YEL169D
TIME CONTROL UNIT (TCU)
Schematic (Cont’d)
EL-185
System Description
NATS has the following immobiliser functions:
I
This version of NATS has dongle control unit to improve its anti-theft performance (RHD models). Dongle
control unit has its own ID which is registered into NATS IMMU. So if dongle unit is replaced, initialization
must be carried out.
I
When malfunction of dongle unit is detected:
The security indicator lamp illuminates for about 15 minutes after ignition switch is turned to ON.
— When dongle control unit has a malfunction, and the indicator lamp is illuminated, engine can not be
started. However engine can be started only one time when security indicator lamp turns off in about
15 minutes after ignition switch is turned to ON.
I
Since only NATS ignition keys, whose ID nos. have been registered into the ECM and IMMU of NATS,
allow the engine to run, operation of a stolen vehicle without a NATS registered key is prevented by NATS.
That is to say, NATS will immobilize the engine if someone tries to start it without the registered key of
NATS.
I
All of the originally supplied ignition key IDs have been NATS registered.
If requested by the vehicle owner, a maximum of five key IDs can be registered into the NATS compo-
nents.
I
The NATS security indicator (NATS security ind.) blinks when the ignition switch is in “OFF” or “ACC”
position. Therefore, NATS warns outsiders that the vehicle is equipped with the anti-theft system.
I
When NATS detects trouble, the security indicator lamp lights up as follows.
Condition IGN ON and
With dongle
Without dongle
MIL
Security indicator
MIL
Security indicator
NATS malfunction
(except dongle control
unit) is detected
—
6 times blinking
Staying ON after ignition
switch is turned ON
—
Staying ON
Only malfunction of
dongle control unit is
detected.
—
Staying ON for about 15
minutes after ignition
switch is turned ON
—
—
Malfunction of NATS and
engine related parts are
detected.
Staying ON
6 times blinking
Staying ON after ignition
switch is turned ON
Staying ON
Staying ON
Only engine related part
malfunction is detected.
Staying ON
—
Staying ON
—
Just after initialization of
NATS
—
6 times blinking
—
—
I
NATS trouble diagnoses, system initialisation and additional registration of other NATS ignition key IDs
must be carried out using CONSULT-II hardware and CONSULT-II NATS software.
Regarding the procedures of NATS initialisation and NATS ignition key ID registration, refer to CONSULT-II
operation instruction, NATS.
I
When servicing a malfunction of the NATS (indicated by lighting up of security Indicator Lamp) or
registering another NATS ignition key ID no., it may be necessary to re-register original key iden-
tification. Therefore, be sure to receive all keys and the PIN code from vehicle owner.
NATS (Nissan Anti-Theft System)
EL-186
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст