Nissan Pathfinder (2007 year). Instruction — part 101
NVIS(NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)
BL-101
C
D
E
F
G
H
J
K
L
M
A
B
BL
2007 Pathfinder
Work Flow
EIS007QG
LIIA1152E
BL-102
NVIS(NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)
2007 Pathfinder
Trouble Diagnoses
EIS007QH
SYMPTOM MATRIX CHART 1
Self-diagnosis related item
*: When NVIS (NATS) detects trouble, the security indicator lights up while ignition key is in the “ON” position.
Symptom
Displayed “SELF-DIAG
RESULTS” on CON-
SULT-II screen.
Diagnostic Procedure
(Reference page)
System
(Malfunctioning part or
mode)
Reference Part No. Of
Illustration On System
Diagram
●
Security indicator
lighting up*
●
Engine cannot be
started
CHAIN OF ECM-IMMU
[P1612]
PROCEDURE 1
(
)
In rare case, “CHAIN OF
ECM-IMMU” might be
stored during key regis-
tration procedure, even if
the system is not mal-
functioning.
—
Open circuit in battery
voltage line of BCM cir-
cuit
C1
Open circuit in ignition
line of BCM circuit
C2
Open circuit in ground
line of BCM circuit
C3
Open or short circuit
between BCM and ECM
communication line
C4
ECM
B
BCM
A
DIFFERENCE OF KEY
[P1615]
PROCEDURE 2
(
)
Unregistered key
D
BCM
A
CHAIN OF IMMU-KEY
[P1614]
PROCEDURE 5
(
)
Malfunction of key ID
chip
E5
Communication line
between ANT/ AMP and
BCM:
Open circuit or short cir-
cuit of battery voltage
line or ground line
E1
E2
Open circuit in power
source line of ANT/ AMP
circuit
E3
Open circuit in ground
line of ANT/ AMP circuit
E4
NATS antenna amp.
E6
BCM
A
ID DISCORD, IMM-ECM
[P1611]
PROCEDURE 3
(
)
System initialization has
not yet been completed.
F
ECM
B
LOCK MODE
[P1610]
PROCEDURE 4
(
)
LOCK MODE
D
Security indicator light-
ing up*
DON'T ERASE
BEFORE CHECKING
ENG DIAG
WORK FLOW
(
)
Engine trouble data and
NVIS (NATS) trouble
data have been detected
in ECM
—
NVIS(NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)
BL-103
C
D
E
F
G
H
J
K
L
M
A
B
BL
2007 Pathfinder
SYMPTOM MATRIX CHART 2
Non self-diagnosis related item
*: CONSULT-II self-diagnostic results display screen “no malfunction is detected”.
DIAGNOSTIC SYSTEM DIAGRAM
Symptom
Diagnostic Procedure
(Reference page)
System
(Malfunctioning part or mode)
Reference Part No. Of Illustra-
tion On System Diagram
Security indicator does not light
up*.
PROCEDURE 6
(
)
Combination meter (security
indictor lamp)
—
Open circuit between Fuse and
BCM
—
BCM
A
WIIA0550E
BL-104
NVIS(NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)
2007 Pathfinder
Diagnostic Procedure 1
EIS007QI
Self-diagnostic results:
“CHAIN OF ECM-IMMU” displayed on CONSULT-II screen
First perform the “SELF-DIAG RESULTS” in “BCM” with CONSULT-II, then perform the trouble diagno-
sis of malfunction system indicated “SELF-DIAG RESULTS” of “BCM”. Refer to
1.
CONFIRM SELF-DIAGNOSTIC RESULTS
Confirm SELF-DIAGNOSTIC RESULTS “CHAIN OF ECM-IMMU”
displayed on CONSULT-II screen.
NOTE:
In rare case, “CHAIN OF ECM-IMMU” might be stored during key
registration procedure, even if the system is not malfunctioning.
Is CONSULT-II screen displayed as above?
Yes
>> GO TO 2.
No
>> GO TO
BL-102, "SYMPTOM MATRIX CHART 1"
.
2.
CHECK POWER SUPPLY CIRCUIT FOR BCM
1.
Turn ignition switch OFF.
2.
Check voltage between BCM connector M20 terminal 70 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Check the following:
●
50A fusible link (letter g , located in fuse and fusible
link box)
●
Harness for open or short between fuse and BCM
connector
Ref. Part No. C1
3.
CHECK IGN SW. ON SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between BCM connector M18 terminal 38 and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Check the following:
●
10A fuse [No. 1, located in the fuse block (J/B)]
●
Harness for open or short between fuse and BCM
connector
Ref. part No. C2
PIIA1260E
70 - Ground
: Battery voltage
LIIA1279E
38 - Ground
: Battery voltage
LIIA0527E
NVIS(NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)
BL-105
C
D
E
F
G
H
J
K
L
M
A
B
BL
2007 Pathfinder
4.
CHECK GROUND CIRCUIT FOR BCM
1.
Turn ignition switch OFF.
2.
Disconnect BCM.
3.
Check continuity between BCM connector M20 terminal 67 and ground.
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace harness. Ref. part No. C3
5.
REPLACE BCM
1.
Replace BCM. Ref. part No. A
2.
Perform initialization with CONSULT-II.
For initialization, refer to “CONSULT-II Operation Instruction NATS-IVIS/NVIS”.
Does the engine start?
Yes
>> BCM is malfunctioning.
No
>> ECM is malfunctioning.
●
Replace ECM. Ref. part No. B
●
Perform initialization or re-communicating function.
●
For initialization, refer to “CONSULT-II Operation Instruction NATS-IVIS/NVIS”.
●
For re-communicating function, refer to
BL-96, "ECM Re-communicating Function"
.
Diagnostic Procedure 2
EIS007QJ
Self-diagnostic results:
“DIFFERENCE OF KEY” displayed on CONSULT-II screen
1.
CONFIRM SELF-DIAGNOSTIC RESULTS
Confirm SELF-DIAGNOSTIC RESULTS “DIFFERENCE OF KEY”
displayed on CONSULT-II screen.
Is CONSULT-II screen displayed as above?
Yes
>> GO TO 2.
No
>> GO TO
BL-102, "SYMPTOM MATRIX CHART 1"
67 - Ground
:Continuity should exist.
LIIA1040E
PIIA1261E
BL-106
NVIS(NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)
2007 Pathfinder
2.
PERFORM INITIALIZATION WITH CONSULT-II
Perform initialization with CONSULT-II. Re-register all NATS ignition key IDs.
For initialization and registration of NATS ignition key IDs, refer to “CONSULT-II Operation Instruction NATS-IVIS/
NVIS”.
NOTE:
If the initialization is not completed or malfunctions, CONSULT-II
shows message on the screen.
Can the system be initialized and can the engine be started with re-
registered NATS ignition key?
Yes
>> Ignition key ID was unregistered. Ref. part No. D
No
>> BCM is malfunctioning.
●
Replace BCM. Ref. part No. A
●
Perform initialization with CONSULT-II.
●
For initialization, refer to “CONSULT-II Operation
Instruction NATS-IVIS/NVIS”.
Diagnostic Procedure 3
EIS007QK
Self-diagnostic results:
“ID DISCORD, IMM-ECM” displayed on CONSULT-II screen
1.
CONFIRM SELF-DIAGNOSTIC RESULTS
Confirm SELF-DIAGNOSTIC RESULTS “ID DISCORD, IMM-ECM” displayed on CONSULT-II screen.
NOTE:
“ID DISCORD IMM-ECM”:
Registered ID of BCM is in discord with that of ECM.
Is CONSULT-II screen displayed as above?
Yes
>> GO TO 2.
No
>> GO TO
BL-102, "SYMPTOM MATRIX CHART 1"
.
2.
PERFORM INITIALIZATION WITH CONSULT-II
Perform initialization with CONSULT-II. Re-register all NATS ignition key IDs.
For initialization, refer to “CONSULT-II Operation Instruction NATS-
IVIS/NVIS”.
NOTE:
If the initialization is not completed or malfunctions, CONSULT-II
shows message on the screen.
Can the system be initialized?
Yes
>>
●
Start engine. (END)
●
(System initialization had not been completed. Ref.
part No. F )
No
>> ECM is malfunctioning.
●
Replace ECM. Ref. part No. B
●
Perform initialization with CONSULT-II.
For initialization, refer to “CONSULT-II Operation Instruction NATS-IVIS/NVIS”.
SEL297W
PIIA1262E
SEL297W
NVIS(NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)
BL-107
C
D
E
F
G
H
J
K
L
M
A
B
BL
2007 Pathfinder
Diagnostic Procedure 4
EIS007QL
Self-diagnostic results:
“LOCK MODE” displayed on CONSULT-II screen
1.
CONFIRM SELF-DIAGNOSTIC RESULTS
Confirm SELF-DIAGNOSTIC RESULTS “LOCK MODE” is displayed
on CONSULT-II screen.
Is CONSULT-II screen displayed as above?
Yes
>> GO TO 2.
No
>> GO TO
BL-102, "SYMPTOM MATRIX CHART 1"
2.
ESCAPE FROM LOCK MODE
1.
Turn ignition switch OFF.
2.
Turn ignition switch ON with registered key. (Do not start engine.) Wait 5 seconds.
3.
Return the key to OFF position. Wait 5 seconds.
4.
Repeat steps 2 and 3 twice (total of three cycles).
5.
Start the engine.
Does engine start?
Yes
>> System is OK (Now system is escaped from “LOCK MODE”). Clear all codes.
No
>> GO TO 3.
3.
PERFORM INITIALIZATION WITH CONSULT-II
Perform initialization with CONSULT-II.
For initialization, refer to “CONSULT-II Operation Instruction NATS-
IVIS/NVIS”.
NOTE:
If the initialization is not completed or malfunctions, CONSULT-II
shows the message on the screen.
Can the system be initialized?
Yes
>> System is OK.
No
>> GO TO 4.
PIIA1264E
SEL297W
BL-108
NVIS(NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)
2007 Pathfinder
4.
PERFORM INITIALIZATION WITH CONSULT-II AGAIN
1.
Replace BCM.
2.
Perform initialization with CONSULT-II.
For initialization, refer to “CONSULT-II Operation Instruction NATS-
IVIS/NVIS”.
NOTE:
If the initialization is not completed or malfunctions, CONSULT-II
shows the message on the screen.
Can the system be initialized?
Yes
>> System is OK. BCM is malfunctioning. Ref. part No. A
No
>> ECM is malfunctioning.
●
Replace ECM. Ref. part No. B
●
Perform initialization with CONSULT-II.
For initialization, refer to “CONSULT-II Operation
Instruction NATS-IVIS/NVIS”.
Diagnostic Procedure 5
EIS007QM
Self-diagnostic results:
“CHAIN OF IMMU-KEY” displayed on CONSULT-II screen
1.
CONFIRM SELF-DIAGNOSTIC RESULTS
Confirm SELF-DIAGNOSTIC RESULTS “CHAIN OF IMMU-KEY”
displayed on CONSULT-II screen.
Is CONSULT-II screen displayed as above?
Yes
>> GO TO 2.
No
>> GO TO
BL-102, "SYMPTOM MATRIX CHART 1"
.
2.
CHECK NATS ANTENNA AMP. INSTALLATION
Check NATS antenna amp. installation. Refer to
BL-112, "How to Replace NATS Antenna Amp."
.
OK or NG
OK
>> GO TO 3.
NG
>> Reinstall NATS antenna amp. correctly.
3.
CHECK NVIS (NATS) IGNITION KEY ID CHIP
Start engine with another registered NATS ignition key.
Does the engine start?
Yes
>> Ignition key ID chip is malfunctioning.
●
Replace the ignition key.
Ref. part No. E5
●
Perform initialization with CONSULT-II.
For initialization, refer to “CONSULT-II Operation Instruction NATS-IVIS/NVIS”.
No
>> GO TO 4.
SEL297W
PIIA1263E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст