Nissan Pathfinder (2007 year). Instruction — part 276
FRONT DOOR GLASS AND REGULATOR
GW-61
C
D
E
F
G
H
J
K
L
M
A
B
GW
2007 Pathfinder
FRONT DOOR GLASS AND REGULATOR
PFP:80300
Front Door Glass
EIS007S0
REMOVAL
1.
Remove the front door finisher. Refer to
.
2.
Temporarily reconnect the power window switch.
3.
Operate the power window main switch to raise/lower the door
window until the glass bolts can be seen.
4.
Remove the inside seal.
5.
Remove the glass bolts.
6.
While holding the door window, raise it at the rear and pull the
glass out of the sash toward the outside of the door.
INSTALLATION
Installation is in the reverse order of removal.
●
Check the glass for proper fit. Refer to
●
On the drivers door, reset the motor. Refer to
GW-64, "SETTING AFTER INSTALLATION"
FITTING INSPECTION
●
Check that the glass is securely fit into the glass run groove.
●
Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)] and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator bolts,
guide rail bolts, and glass and guide rail bolts to correct the glass position.
LIIA1686E
LIIA1687E
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
GW-62
FRONT DOOR GLASS AND REGULATOR
2007 Pathfinder
Front Door Glass Regulator
EIS007S1
REMOVAL
1.
Remove the front door finisher. Refer to
2.
Temporarily reconnect the power window switch.
3.
Operate the power window main switch to raise/lower the door
window until the glass bolts can be seen.
4.
Remove the inside seal.
5.
Remove the glass bolts.
6.
Raise the front door glass and hold it in place with suitable tool.
7.
Disconnect the harness connector from the regulator assembly.
8.
Remove the bolts and the regulator assembly.
DISASSEMBLY AND ASSEMBLY
Remove the regulator motor from the regulator assembly.
INSPECTION AFTER REMOVAL
Check the regulator assembly for the following items. If a malfunction is detected, replace or grease it.
●
Wire wear
●
Regulator deformation
●
Grease condition for each sliding part
LIIA1686E
WIIA1033E
FRONT DOOR GLASS AND REGULATOR
GW-63
C
D
E
F
G
H
J
K
L
M
A
B
GW
2007 Pathfinder
INSTALLATION
1.
Install the regulator assembly.
a.
Loosely install the top rear regulator bolt to use along with the temporary holds on the window motor to
install the assembly in the door.
b.
Install the top front regulator bolt.
c.
Install the bottom front regulator bolt.
d.
Install the bottom rear regulator bolt.
e.
Tighten the top rear regulator bolt.
f.
Install the top window motor bolt.
g.
Install the lower window motor bolt
h.
Install the rear window motor bolt.
2.
Connect the harness connector to the regulator assembly.
3.
Lower the glass and ensure that it is in both the front and rear
glass channels. Tighten glass bolts.
4.
Check the glass for proper fit. Refer to
5.
On the drivers door, reset the motor. Refer to
GW-64, "SETTING AFTER INSTALLATION"
6.
Install the inside seal.
WIIA1033E
Regulator and motor bolts
: 5.7 N·m (0.58 kg-m, 50 in-lb)
Glass mounting bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
LIIA1686E
GW-64
FRONT DOOR GLASS AND REGULATOR
2007 Pathfinder
7.
Install front door finisher. Refer to
SETTING AFTER INSTALLATION
Setting of Limit Switch
If any of the following work has been done, set the limit switch (integrated in the motor).
●
Removal and installation of the regulator.
●
Removal and installation of the motor from the regulator.
●
Removal and installation of the glass.
●
Removal and installation of the glass run.
Resetting
After installing each component, perform the following procedure to reset the limit switch.
1.
Raise the glass to the top position.
2.
While pressing and holding the reset switch, lower the glass to
the bottom position.
3.
Release the reset switch. Verify that the reset switch returns to
the original position, if not, pull the switch using suitable tool.
4.
Raise the glass to the top position.
CAUTION:
Do not operate the glass automatically to raise the glass to the
top position.
SIIA0347E
REAR DOOR GLASS AND REGULATOR
GW-65
C
D
E
F
G
H
J
K
L
M
A
B
GW
2007 Pathfinder
REAR DOOR GLASS AND REGULATOR
PFP:82300
Rear Door Glass
EIS007S2
REMOVAL
1.
Remove the rear door finisher. Refer to
.
2.
Remove the inside seal.
3.
Temporarily reconnect the power window switch.
4.
Remove the glass run from the partition glass.
5.
Operate the power window switch to raise/lower the door win-
dow until the glass bolts can be seen.
6.
Remove the partition sash bolt (lower) and screw (upper) to
remove the sash.
7.
Remove the bolts and the glass.
INSTALLATION
Installation is in the reverse order of removal.
●
Check the glass alignment. Refer to
FITTING INSPECTION
●
Check that the glass is securely fit into the glass run groove.
●
Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)], and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator bolts,
guide rail bolts, and glass carrier plate bolts to correct the glass position.
LIIA1689E
Glass bolts
: 5.7 N·m (0.58 kg-m, 50 in-lb)
GW-66
REAR DOOR GLASS AND REGULATOR
2007 Pathfinder
Rear Door Glass Regulator
EIS007S3
REMOVAL
1.
Remove the rear door finisher. Refer to
2.
Remove the inside seal.
3.
Temporarily reconnect the power window switch.
4.
Operate the power window switch to raise/lower the door win-
dow until the glass bolts can be seen.
5.
Raise the rear door glass and hold it in place with suitable tool.
6.
Remove the bolts and the regulator assembly.
●
Disconnect the connector from the regulator assembly.
INSPECTION AFTER REMOVAL
Check the regulator assembly for the following items. If a malfunction is detected, replace or grease it.
●
Gear wear
●
Regulator deformation
●
Spring damage
●
Grease condition for each sliding part
LIIA1689E
WIIA1034E
REAR DOOR GLASS AND REGULATOR
GW-67
C
D
E
F
G
H
J
K
L
M
A
B
GW
2007 Pathfinder
INSTALLATION
1.
Connect the harness connector and install the regulator assembly.
a.
Loosely install the top rear regulator bolt to use along with the temporary holds on the window motor to
install the assembly in the door.
b.
Install the top front regulator bolt.
c.
Install the bottom regulator bolt.
d.
Tighten the top rear regulator bolt.
e.
Install the top window motor bolt.
f.
Install the lower window motor bolt.
g.
Install the front window motor bolt.
2.
Lower the glass and ensure that it is in both the front and rear
glass channels. Tighten the bolts.
3.
Install the partition sash
4.
Check the glass alignment. Refer to
5.
Install the inside seal.
6.
Install the rear door finisher. Refer to
Regulator assembly
: 7.5 N·m (0.77 kg-m, 66 in-lb)
Glass bolts
: 5.7 N·m (0.58 kg-m, 50 in-lb)
WIIA1034E
LIIA1689E
GW-68
SIDE WINDOW GLASS
2007 Pathfinder
SIDE WINDOW GLASS
PFP:83300
Removal and Installation
EIS007S4
WIIA1035E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст