Nissan Pathfinder (2007 year). Instruction — part 27
TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-187
D
E
F
G
H
I
J
K
L
M
A
B
AT
2007 Pathfinder
7.
DETECT MALFUNCTIONING ITEM
1.
Check control valve with TCM. Refer to
AT-227, "Control Valve With TCM and A/T Fluid Temperature Sen-
.
2.
Disassemble A/T. Refer to
3.
Check the following.
–
Oil pump assembly. Refer to
–
Power train system. Refer to
–
Transmission case. Refer to
.
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace damaged parts.
8.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
AT-227, "Control Valve With TCM and A/T Fluid Temperature Sensor 2"
2.
Check A/T fluid condition. Refer to
AT-52, "Fluid Condition Check"
OK or NG
OK
>> GO TO 9.
NG
>> GO TO 12.
9.
DETECT MALFUNCTIONING ITEM
●
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to
(Symptom No.43).
OK or NG
OK
>> GO TO 10.
NG
>> Repair or replace damaged parts.
10.
CHECK SYMPTOM
Check again. Refer to
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 11.
11.
PERFORM TCM INSPECTION
1.
Perform TCM input/output signals inspection. Refer to
AT-85, "TCM Input/Output Signal Reference Val-
2.
If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness
connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
12.
DETECT MALFUNCTIONING ITEM
●
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to
(Symptom No.43).
OK or NG
OK
>> GO TO 10.
NG
>> Repair or replace damaged parts.
AT-188
TROUBLE DIAGNOSIS FOR SYMPTOMS
2007 Pathfinder
Vehicle Cannot Be Started From D
1
ECS00EL6
SYMPTOM:
Vehicle cannot be started from D
1
on cruise test - Part 1 and cruise test - Part 2.
DIAGNOSTIC PROCEDURE
1.
CONFIRM THE SYMPTOM
Check if vehicle creeps in “R” position.
OK or NG
OK
>> GO TO 2.
NG
>> Refer to
AT-183, "Vehicle Does Not Creep Backward In “R” Position"
2.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
AT-88, "SELF-DIAGNOSTIC RESULT MODE"
Is any malfunction detected by self-diagnostic results?
YES
>> Check the malfunctioning system. Refer to
AT-88, "SELF-DIAGNOSTIC RESULT MODE"
NO
>> GO TO 3.
3.
CHECK ACCELERATOR PEDAL POSITION (APP) SENSOR
Check accelerator pedal position (APP) sensor. Refer to
AT-124, "DTC P1705 THROTTLE POSITION SEN-
.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace accelerator pedal position (APP) sensor.
4.
CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to
AT-12, "Checking the A/T Fluid (ATF)"
OK or NG
OK
>> GO TO 5.
NG
>> Refill ATF.
5.
CHECK LINE PRESSURE
Check line pressure at the engine stall point. Refer to
OK or NG
OK
>> GO TO 8.
NG - 1 >> Line pressure high. GO TO 6.
NG - 2 >> Line pressure low. GO TO 7.
6.
DETECT MALFUNCTIONING ITEM
1.
Check control valve with TCM. Refer to
AT-227, "Control Valve With TCM and A/T Fluid Temperature Sen-
2.
Disassemble A/T. Refer to
3.
Check the following.
–
.
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace damaged parts.
TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-189
D
E
F
G
H
I
J
K
L
M
A
B
AT
2007 Pathfinder
7.
DETECT MALFUNCTIONING ITEM
1.
Check control valve with TCM. Refer to
AT-227, "Control Valve With TCM and A/T Fluid Temperature Sen-
.
2.
Disassemble A/T. Refer to
3.
Check the following.
–
Oil pump assembly. Refer to
–
Power train system. Refer to
–
Transmission case. Refer to
.
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace damaged parts.
8.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
AT-227, "Control Valve With TCM and A/T Fluid Temperature Sensor 2"
2.
Check A/T fluid condition. Refer to
AT-52, "Fluid Condition Check"
OK or NG
OK
>> GO TO 9.
NG
>> GO TO 12.
9.
DETECT MALFUNCTIONING ITEM
●
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to
(Symptom No.23).
OK or NG
OK
>> GO TO 10.
NG
>> Repair or replace damaged parts.
10.
CHECK SYMPTOM
Check again. Refer to
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 11.
11.
PERFORM TCM INSPECTION
1.
Perform TCM input/output signals inspection. Refer to
AT-85, "TCM Input/Output Signal Reference Val-
2.
If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness
connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
12.
DETECT MALFUNCTIONING ITEM
●
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to
(Symptom No.23).
OK or NG
OK
>> GO TO 10.
NG
>> Repair or replace damaged parts.
AT-190
TROUBLE DIAGNOSIS FOR SYMPTOMS
2007 Pathfinder
A/T Does Not Shift: D
1
→
D
2
ECS00EL7
SYMPTOM:
The vehicle does not shift-up from the D
1
to D
2
gear at the specified speed.
DIAGNOSTIC PROCEDURE
1.
CONFIRM THE SYMPTOM
Check if vehicle creeps forward in “D” position and vehicle can be started from D
1.
OK or NG
OK
>> GO TO 2.
NG
>> Refer to
AT-186, "Vehicle Does Not Creep Forward In “D” Position"
,
.
2.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
AT-88, "SELF-DIAGNOSTIC RESULT MODE"
Is any malfunction detected by self-diagnostic results?
YES
>> Check the malfunctioning system. Refer to
AT-88, "SELF-DIAGNOSTIC RESULT MODE"
NO
>> GO TO 3.
3.
CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to
AT-12, "Checking the A/T Fluid (ATF)"
OK or NG
OK
>> GO TO 4.
NG
>> Refill ATF.
4.
CHECK LINE PRESSURE
Check line pressure at the engine stall point. Refer to
OK or NG
OK
>> GO TO 7.
NG - 1 >> Line pressure high. GO TO 5.
NG - 2 >> Line pressure low. GO TO 6.
5.
DETECT MALFUNCTIONING ITEM
1.
Check control valve with TCM. Refer to
AT-227, "Control Valve With TCM and A/T Fluid Temperature Sen-
2.
Disassemble A/T. Refer to
3.
Check the following.
–
.
OK or NG
OK
>> GO TO 7.
NG
>> Repair or replace damaged parts.
TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-191
D
E
F
G
H
I
J
K
L
M
A
B
AT
2007 Pathfinder
6.
DETECT MALFUNCTIONING ITEM
1.
Check control valve with TCM. Refer to
AT-227, "Control Valve With TCM and A/T Fluid Temperature Sen-
.
2.
Disassemble A/T. Refer to
3.
Check the following.
–
Oil pump assembly. Refer to
–
Power train system. Refer to
–
Transmission case. Refer to
.
OK or NG
OK
>> GO TO 7.
NG
>> Repair or replace damaged parts.
7.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
AT-227, "Control Valve With TCM and A/T Fluid Temperature Sensor 2"
2.
Check A/T fluid condition. Refer to
AT-52, "Fluid Condition Check"
OK or NG
OK
>> GO TO 8.
NG
>> GO TO 11.
8.
DETECT MALFUNCTIONING ITEM
●
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to
(Symptom No.10).
OK or NG
OK
>> GO TO 9.
NG
>> Repair or replace damaged parts.
9.
CHECK SYMPTOM
Check again. Refer to
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 10.
10.
PERFORM TCM INSPECTION
1.
Perform TCM input/output signals inspection. Refer to
AT-85, "TCM Input/Output Signal Reference Val-
2.
If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness
connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
11.
DETECT MALFUNCTIONING ITEM
●
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to
(Symptom No.10).
OK or NG
OK
>> GO TO 9.
NG
>> Repair or replace damaged parts.
AT-192
TROUBLE DIAGNOSIS FOR SYMPTOMS
2007 Pathfinder
A/T Does Not Shift: D
2
→
D
3
ECS00EL8
SYMPTOM:
The vehicle does not shift-up from D
2
to D
3
gear at the specified speed.
DIAGNOSTIC PROCEDURE
1.
CONFIRM THE SYMPTOM
Check if vehicle creeps forward in “D” position and vehicle can be started from D
1.
OK or NG
OK
>> GO TO 2.
NG
>> Refer to
AT-186, "Vehicle Does Not Creep Forward In “D” Position"
,
.
2.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
AT-88, "SELF-DIAGNOSTIC RESULT MODE"
Is any malfunction detected by self-diagnostic results?
YES
>> Check the malfunctioning system. Refer to
AT-88, "SELF-DIAGNOSTIC RESULT MODE"
NO
>> GO TO 3.
3.
CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to
AT-12, "Checking the A/T Fluid (ATF)"
OK or NG
OK
>> GO TO 4.
NG
>> Refill ATF.
4.
CHECK LINE PRESSURE
Check line pressure at the engine stall point. Refer to
OK or NG
OK
>> GO TO 7.
NG - 1 >> Line pressure high. GO TO 5.
NG - 2 >> Line pressure low. GO TO 6.
5.
DETECT MALFUNCTIONING ITEM
1.
Check control valve with TCM. Refer to
AT-227, "Control Valve With TCM and A/T Fluid Temperature Sen-
2.
Disassemble A/T. Refer to
3.
Check the following.
–
.
OK or NG
OK
>> GO TO 7.
NG
>> Repair or replace damaged parts.
TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-193
D
E
F
G
H
I
J
K
L
M
A
B
AT
2007 Pathfinder
6.
DETECT MALFUNCTIONING ITEM
1.
Check control valve with TCM. Refer to
AT-227, "Control Valve With TCM and A/T Fluid Temperature Sen-
.
2.
Disassemble A/T. Refer to
3.
Check the following.
–
Oil pump assembly. Refer to
–
Power train system. Refer to
–
Transmission case. Refer to
.
OK or NG
OK
>> GO TO 7.
NG
>> Repair or replace damaged parts.
7.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
AT-227, "Control Valve With TCM and A/T Fluid Temperature Sensor 2"
2.
Check A/T fluid condition. Refer to
AT-52, "Fluid Condition Check"
OK or NG
OK
>> GO TO 8.
NG
>> GO TO 11.
8.
DETECT MALFUNCTIONING ITEM
●
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to
(Symptom No.11).
OK or NG
OK
>> GO TO 9.
NG
>> Repair or replace damaged parts.
9.
CHECK SYMPTOM
Check again. Refer to
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 10.
10.
PERFORM TCM INSPECTION
1.
Perform TCM input/output signals inspection. Refer to
AT-85, "TCM Input/Output Signal Reference Val-
2.
If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness
connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
11.
DETECT MALFUNCTIONING ITEM
●
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to
(Symptom No.11).
OK or NG
OK
>> GO TO 9.
NG
>> Repair or replace damaged parts.
AT-194
TROUBLE DIAGNOSIS FOR SYMPTOMS
2007 Pathfinder
A/T Does Not Shift: D
3
→
D
4
ECS00EL9
SYMPTOM:
●
The vehicle does not shift-up from the D
3
to D
4
gear at the specified speed.
DIAGNOSTIC PROCEDURE
1.
CONFIRM THE SYMPTOM
Check if vehicle creeps forward in “D” position and vehicle can be started from D
1.
OK or NG
OK
>> GO TO 2.
NG
>> Refer to
AT-186, "Vehicle Does Not Creep Forward In “D” Position"
,
.
2.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
AT-88, "SELF-DIAGNOSTIC RESULT MODE"
Is any malfunction detected by self-diagnostic results?
YES
>> Check the malfunctioning system. Refer to
AT-88, "SELF-DIAGNOSTIC RESULT MODE"
NO
>> GO TO 3.
3.
CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to
AT-12, "Checking the A/T Fluid (ATF)"
OK or NG
OK
>> GO TO 4.
NG
>> Refill ATF.
4.
CHECK LINE PRESSURE
Check line pressure at the engine stall point. Refer to
OK or NG
OK
>> GO TO 7.
NG - 1 >> Line pressure high. GO TO 5.
NG - 2 >> Line pressure low. GO TO 6.
5.
DETECT MALFUNCTIONING ITEM
1.
Check control valve with TCM. Refer to
AT-227, "Control Valve With TCM and A/T Fluid Temperature Sen-
2.
Disassemble A/T. Refer to
3.
Check the following.
–
.
OK or NG
OK
>> GO TO 7.
NG
>> Repair or replace damaged parts.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст