Nissan Pathfinder (2007 year). Instruction — part 279
REAR WINDOW DEFOGGER
GW-85
C
D
E
F
G
H
J
K
L
M
A
B
GW
2007 Pathfinder
5.
CHECK DOOR MIRROR DEFOGGER
Check continuity between each door mirror LH or RH terminals 1
and 6.
OK or NG
OK
>> Repair or replace harness.
NG
>> Replace malfunctioning door mirror LH or RH. Refer to
Door Mirror LH Defogger Circuit Check
EIS007SM
1.
CHECK DOOR MIRROR LH DEFOGGER POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect door mirror LH.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror LH connector and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace harness.
2.
CHECK DOOR MIRROR LH DEFOGGER GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror LH connector D4 terminal
6 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
1 - 6
: Continuity should exist.
LIIA2038E
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
D4
1
Ground
Rear window defogger
switch ON
Battery voltage
Rear window defogger
switch OFF
0
LIIA2050E
6 - Ground
: Continuity should exist.
LIIA2037E
GW-86
REAR WINDOW DEFOGGER
2007 Pathfinder
3.
CHECK DOOR MIRROR LH DEFOGGER
Check continuity between door mirror LH terminals 1 and 6.
OK or NG
OK
>> Repair or replace harness.
NG
>> Replace door mirror LH. Refer to
Door Mirror RH Defogger Circuit Check
EIS007SN
1.
CHECK DOOR MIRROR RH DEFOGGER POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect door mirror RH.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror RH connector and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace harness.
2.
CHECK DOOR MIRROR RH DEFOGGER GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror RH connector D107 termi-
nal 6 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
1 - 6
: Continuity should exist.
LIIA2038E
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
D107
1
Ground
Rear window defogger
switch ON
Battery voltage
Rear window defogger
switch OFF
0
LIIA2050E
6 - Ground
: Continuity should exist.
LIIA2037E
REAR WINDOW DEFOGGER
GW-87
C
D
E
F
G
H
J
K
L
M
A
B
GW
2007 Pathfinder
3.
CHECK DOOR MIRROR RH DEFOGGER
Check continuity between each door mirror RH terminals 1 and 6.
OK or NG
OK
>> Repair or replace harness.
NG
>> Replace door mirror RH. Refer to
Rear Window Defogger Signal Check (With NAVI)
EIS007SO
1.
CHECK AV COMMUNICATION LINE
AV communication line check is executed. Refer to
AV-130, "CAN Communication Line Check"
OK or NG
OK
>> GO TO 2.
NG
>> Replace display control unit. Refer to
2.
CHECK CAN COMMUNICATION LINE
CAN communication line check is executed. Refer to
AV-130, "CAN Communication Line Check"
OK or NG
OK
>> Check the condition of the harness and the connector.
NG
>> In addition, it is necessary to check CAN communication line. Refer to
.
Filament Check
EIS007SP
1.
When measuring voltage, wrap tin foil around the top of the neg-
ative probe. Then press the foil against the wire with your finger.
2.
Attach probe circuit tester (in Volt range) to middle portion of
each filament.
1 - 6
: Continuity should exist.
LIIA2038E
Is rear window defogger displayed on the display?
SEL122R
SEL263
GW-88
REAR WINDOW DEFOGGER
2007 Pathfinder
3.
If a filament is burned out, circuit tester registers 0 or battery
voltage.
4.
To locate burned out point, move probe to left and right along fil-
ament. Test needle will swing abruptly when probe passes the
point.
Filament Repair
EIS007SQ
REPAIR EQUIPMENT
●
Conductive silver composition (DuPont No. 4817 or equivalent)
●
Ruler 30 cm (11.8 in) long
●
Drawing pen
●
Heat gun
●
Alcohol
●
Cloth
REPAIRING PROCEDURE
1.
Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.
2.
Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use.
3.
Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
4.
After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.
SEL265
PIIA0215E
SEL012D
REAR WINDOW DEFOGGER
GW-89
C
D
E
F
G
H
J
K
L
M
A
B
GW
2007 Pathfinder
5.
Apply a constant stream of hot air directly to the repaired area
for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.
SEL013D
GW-90
DOOR MIRROR
2007 Pathfinder
DOOR MIRROR
PFP:96301
Wiring Diagram — MIRROR —
EIS007SR
WITHOUT HEATED MIRRORS
WIWA2116E
DOOR MIRROR
GW-91
C
D
E
F
G
H
J
K
L
M
A
B
GW
2007 Pathfinder
WITH HEATED MIRRORS
WIWA2117E
GW-92
DOOR MIRROR
2007 Pathfinder
Door Mirror Assembly
EIS007SS
REMOVAL
NOTE:
Be careful not to damage the mirror bodies.
1.
Remove the adhesive front door sash cover.
2.
Remove the front door finisher. Refer to
3.
Position the front door seal aside.
4.
Disconnect the door mirror harness connector.
5.
Remove the nuts and the door mirror assembly.
INSTALLATION
Installation is in the reverse order of removal.
WIIA1036E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст