Nissan Pathfinder (2007 year). Instruction — part 312
ILLUMINATION
LT-137
C
D
E
F
G
H
I
J
L
M
A
B
LT
2007 Pathfinder
WKWA4244E
LT-138
ILLUMINATION
2007 Pathfinder
WKWA5354E
ILLUMINATION
LT-139
C
D
E
F
G
H
I
J
L
M
A
B
LT
2007 Pathfinder
WKWA4245E
LT-140
ILLUMINATION
2007 Pathfinder
WKWA5355E
ILLUMINATION
LT-141
C
D
E
F
G
H
I
J
L
M
A
B
LT
2007 Pathfinder
Removal and Installation
EKS00FXP
ILLUMINATION CONTROL SWITCH
The illumination control switch is a function of the combination meter,
and not serviced separately. For replacement, refer to
LKIA0579E
LT-142
BULB SPECIFICATIONS
2007 Pathfinder
BULB SPECIFICATIONS
PFP:26297
Headlamp
EKS00FXQ
*: Always check with the Parts Department for the latest parts information.
Exterior Lamp
EKS00FXR
*: Always check with the Parts Department for the latest parts information.
Interior Lamp/Illumination
EKS00FXS
*: Always check with the Parts Department for the latest parts information.
Item
Wattage (W)*
Low/High
65/55 (HB5)
Item
Wattage (W)*
Front combination lamp
Turn signal lamp/parking lamp
28/8
Side marker
3.8
Rear combination lamp
Stop/Tail lamp
27/8
Turn signal lamp
27
Back-up lamp
18
Front fog lamp
55
License plate lamp
5
High-mounted stop lamp
*
Item
Wattage (W)*
Glove box lamp
3.4
Room/Map lamp
8
A/T device lamp
3
Cargo lamp
8
Vanity lamp
*
Personal lamp
8
LU-1
ENGINE LUBRICATION SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION
LU
A
LU
2007 Pathfinder
PRECAUTIONS . . . . . . . . . . . . . . .. 2
LIQUID GASKET APPLICATION PROCEDURE
PREPARATION . . . . . . . . . . . . . . ... 4
Special Service Tools . . . . . . . . . . . ... 4
Commercial Service Tools . . . . . . . . . . 4
LUBRICATION SYSTEM . . . . . . . . . . . 5
Lubrication Circuit . . . . . . . . . . . . . 5
System Chart . . . . . . . . . . . . . . ... 6
ENGINE OIL . . . . . . . . . . . . . . . ... 7
Inspection . . . . . . . . . . . . . . . . . 7
Changing Engine Oil . . . . . . . . . . . . 9
OIL FILTER . . . . . . . . . . . . . . . ... 10
Changing Oil Filter . . . . . . . . . . . . . 10
OIL COOLER . . . . . . . . . . . . . . . 11
Removal and Installation . . . . . . . . . . 11
OIL PUMP . . . . . . . . . . . . . . . . . 13
Removal and Installation . . . . . . . . . . 13
Disassembly and Assembly . . . . . . . . . 13
SERVICE DATA AND SPECIFICATIONS (SDS) . .. 16
LU-2
PRECAUTIONS
2007 Pathfinder
PRECAUTIONS
PFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
EBS00T2H
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
●
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Liquid Gasket
EBS00QCE
LIQUID GASKET APPLICATION PROCEDURE
1.
Remove old liquid gasket adhering to the liquid gasket applica-
tion surface and the mating surface, Using scraper.
●
Remove liquid gasket completely from the groove of the liquid
gasket application surface, bolts, and bolt holes.
2.
Thoroughly clean the mating surfaces and remove adhering
moisture, grease and foreign materials.
3.
Attach liquid gasket tube to Tool.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-47, "Recommended Chemical Products and Sealants"
4.
Apply liquid gasket without breaks to the specified location with
the specified dimensions.
●
If there is a groove for the liquid gasket application, apply liq-
uid gasket to the groove.
PBIC0003E
Tool number
: WS39930000 (
—
)
WBIA0567E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст