Nissan Pathfinder (2007 year). Instruction — part 296
HEADLAMP (FOR USA)
LT-9
C
D
E
F
G
H
I
J
L
M
A
B
LT
2007 Pathfinder
WKWA2018E
LT-10
HEADLAMP (FOR USA)
2007 Pathfinder
WKWA2019E
HEADLAMP (FOR USA)
LT-11
C
D
E
F
G
H
I
J
L
M
A
B
LT
2007 Pathfinder
WKWA4222E
LT-12
HEADLAMP (FOR USA)
2007 Pathfinder
Terminals and Reference Values for BCM
EKS00FU4
Refer to
BCS-12, "Terminals and Reference Values for BCM"
.
Terminals and Reference Values for IPDM E/R
EKS00FU5
Refer to
PG-27, "Terminals and Reference Values for IPDM E/R"
How to Proceed With Trouble Diagnosis
EKS00FU6
1.
Confirm the symptom or customer complaint.
2.
Understand operation description and function description. Refer to
3.
Perform the Preliminary Check. Refer to
4.
Check symptom and repair or replace the cause of malfunction.
5.
Does the headlamp operate normally? If YES: GO TO 6. If NO: GO TO 4.
6.
Inspection End.
Preliminary Check
EKS00FU7
CHECK POWER SUPPLY AND GROUND CIRCUIT FOR BCM
Refer to
BCS-16, "BCM Power Supply and Ground Circuit Check"
.
CHECK POWER SUPPLY AND GROUND CIRCUIT FOR IPDM E/R
Refer to
PG-29, "IPDM E/R Power/Ground Circuit Inspection"
.
CONSULT-II Function (BCM)
EKS00FU8
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II START PROCEDURE
Refer to
GI-38, "CONSULT-II Start Procedure"
WORK SUPPORT
Display Item List
DATA MONITOR
Display Item List
BCM diagnostic
test item
Diagnostic mode
Description
Inspection by part
WORK SUPPORT
Supports inspections and adjustments. Commands are transmitted to the BCM
for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR
Displays BCM input/output data in real time.
ACTIVE TEST
Operation of electrical loads can be checked by sending drive signal to them.
SELF-DIAG RESULTS
Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication can be read.
ECU PART NUMBER
BCM part number can be read.
CONFIGURATION
Performs BCM configuration read/write functions.
Item
Description
CONSULT-II
Factory setting
BATTERY SAVER SET
Exterior lamp battery saver control mode can be changed
in this mode. Selects exterior lamp battery saver control
mode between ON/OFF.
ON
×
OFF
—
Monitor item
Contents
IGN ON SW
"ON/OFF"
Displays "IGN position (ON)/OFF, ACC position (OFF)" judged from the ignition switch sig-
nal.
ACC ON SW
"ON/OFF"
Displays "ACC (ON)/OFF, Ignition OFF (OFF)" status judged from ignition switch signal.
HI BEAM SW
"ON/OFF"
Displays status (high beam switch: ON/Others: OFF) of high beam switch judged from
lighting switch signal.
HEADLAMP (FOR USA)
LT-13
C
D
E
F
G
H
I
J
L
M
A
B
LT
2007 Pathfinder
ACTIVE TEST
Display Item List
SELF-DIAGNOSTIC RESULTS
Display Item List
CONSULT-II Function (IPDM E/R)
EKS00FU9
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
HEAD LAMP SW 1
"ON/OFF"
Displays status (headlamp switch 1: ON/Others: OFF) of headlamp switch 2 judged from
lighting switch signal.
HEAD LAMP SW 2
"ON/OFF"
Displays status (headlamp switch 2: ON/Others: OFF) of headlamp switch 2 judged from
lighting switch signal.
LIGHT SW 1ST
"ON/OFF"
Displays status (lighting switch 1st position: ON/Others: OFF) of lighting switch judged
from lighting switch signal.
AUTO LIGHT SW
"ON/OFF"
Displays status of the lighting switch as judged from the lighting switch signal. (AUTO posi-
tion: ON/Other than AUTO position: OFF)
PASSING SW
"ON/OFF"
Displays status (flash-to-pass switch: ON/Others: OFF) of flash-to-pass switch judged from
lighting switch signal.
FR FOG SW
"ON/OFF"
Displays status (front fog lamp switch: ON/Others: OFF) of front fog lamp switch judged
from lighting switch signal.
DOOR SW-DR
"ON/OFF"
Displays status of the front door LH as judged from the front door switch LH signal. (Door is
open: ON/Door is closed: OFF)
DOOR SW-AS
"ON/OFF"
Displays status of the front door RH as judged from the front door switch RH signal. (Door
is open: ON/Door is closed: OFF)
DOOR SW-RR
"ON/OFF"
Displays status of the rear door as judged from the rear door switch (RH) signal. (Door is
open: ON/Door is closed: OFF)
DOOR SW-RL
"ON/OFF"
Displays status of the rear door as judged from the rear door switch (LH) signal. (Door is
open: ON/Door is closed: OFF)
BACK DOOR SW
"ON/OFF"
Displays status of the back door as judged from the back door switch signal. (Door is open:
ON/Door is closed: OFF)
TURN SIGNAL R
"ON/OFF"
Displays status (Turn right: ON/Others: OFF) as judged from lighting switch signal.
TURN SIGNAL L
"ON/OFF"
Displays status (Turn left: ON/Others: OFF) as judged from lighting switch signal.
CARGO LAMP SW
"ON/OFF"
Displays status of cargo lamp switch.
OPTICAL SENSOR
[0 - 5V]
Displays "ambient light (close to 5V when dark/close to 0V when light)" judged from optical
sensor signal.
Monitor item
Contents
Test item
Description
TAIL LAMP
Allows tail lamp relay to operate by switching ON-OFF.
HEAD LAMP
Allows headlamp relay (HI, LO) to operate by switching ON-OFF.
FR FOG LAMP
Allows fog lamp relay to operate by switching ON-OFF.
CORNERING LAMP
Not used.
CARGO LAMP
Allows cargo lamp to operate by switching ON-OFF.
Monitored item
CONSULT-ll display
Description
CAN communication
CAN communication [U1000]
Malfunction is detected in CAN communication.
CAN communication system
CAN communication system 1 to 6
[U1000]
Malfunction is detected in CAN system.
IPDM E/R diagnostic mode
Description
SELF-DIAG RESULTS
Displays IPDM E/R self-diagnosis results.
DATA MONITOR
Displays IPDM E/R input/output data in real time.
LT-14
HEADLAMP (FOR USA)
2007 Pathfinder
CONSULT-II START PROCEDURE
Refer to
GI-38, "CONSULT-II Start Procedure"
DATA MONITOR
All Items, Main Items, Select Item Menu
NOTE:
Perform monitoring of IPDM E/R data with the ignition switch ON. When the ignition switch is at ACC, the dis-
play may not be correct.
ACTIVE TEST
Headlamp HI Does Not Illuminate (Both Sides)
EKS00FUA
1.
CHECK COMBINATION SWITCH INPUT SIGNAL
Select "BCM" on CONSULT-II. With "HEAD LAMP" data monitor,
make sure "HI BEAM SW" turns ON-OFF linked with operation of
lighting switch.
OK or NG
OK
>> GO TO 2.
NG
>> Check lighting switch. Refer to
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST
Operation of electrical loads can be checked by sending drive signal to them.
IPDM E/R diagnostic mode
Description
Item name
CONSULT-II
screen display
Display or
unit
Monitor item selection
Description
ALL
SIGNALS
MAIN
SIGNALS
SELECTION
FROM MENU
Parking, license plate
and tail lamps request
TAIL&CLR REQ
ON/OFF
×
×
×
Signal status input from BCM
Headlamp low beam
request
HL LO REQ
ON/OFF
×
×
×
Signal status input from BCM
Headlamp high beam
request
HL HI REQ
ON/OFF
×
×
×
Signal status input from BCM
Daytime lights request
DTRL REQ
ON/OFF
×
–
×
Signal status input from BCM
Front fog lamps request
FR FOG REQ
ON/OFF
×
×
×
Signal status input from BCM
Test item
CONSULT-II screen display
Description
Tail lamp relay output
TAIL LAMP
Allows tail lamp relay to operate by switching operation ON-OFF at
your option.
Headlamp relay (HI, LO) out-
put
LAMPS
Allows headlamp relay (HI, LO) to operate by switching operation
(OFF, HI, LO) at your option (Headlamp high beam repeats ON-OFF
every 1 second).
Front fog lamp relay (FOG)
output
Allows fog lamp relay (FOG) to operate by switching operation ON-
OFF at your option.
When lighting switch is in
HIGH position
: HI BEAM SW ON
SKIA4193E
HEADLAMP (FOR USA)
LT-15
C
D
E
F
G
H
I
J
L
M
A
B
LT
2007 Pathfinder
2.
HEADLAMP ACTIVE TEST
1.
Select "IPDM E/R" on CONSULT-II, and select "ACTIVE TEST"
on "SELECT DIAG MODE" screen.
2.
Select "EXTERNAL LAMPS" on "SELECT TEST ITEM" screen.
3.
Touch "HI" on "ACTIVE TEST" screen.
4.
Make sure headlamp high beam operates.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 4.
3.
CHECK IPDM E/R
1.
Select "IPDM E/R" on CONSULT-II, and select "DATA MONI-
TOR" on "SELECT DIAG MODE" screen.
2.
Make sure "HL LO REQ" and "HL HI REQ" turns ON when light-
ing switch is in HIGH position.
OK or NG
OK
>> Replace IPDM E/R. Refer to
NG
>> Replace BCM. Refer to
BCS-25, "Removal and Installa-
4.
HEADLAMP HIGH FUSE INSPECTION
Inspect 10A fuse No. 34 RH and fuse No. 35 LH (located in IPDM E/R).
OK or NG
OK
>> GO TO 5.
NG
>> Repair harness and replace fuse.
5.
BULB INSPECTION
Inspect inoperative headlamp bulbs.
OK or NG
OK
>> GO TO 6.
NG
>> Replace headlamp bulb.
Headlamp high beam should operate.
WKIA1438E
When lighting switch is in
HIGH position
: HL LO REQ ON
: HL HI REQ ON
SKIA5775E
LT-16
HEADLAMP (FOR USA)
2007 Pathfinder
6.
CHECK HEADLAMP INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front headlamp RH and LH connectors.
3.
Turn ignition switch ON.
4.
Select "IPDM E/R" on CONSULT-II, and select "ACTIVE TEST"
on "SELECT DIAG MODE" screen.
5.
Select "EXTERNAL LAMPS" on "SELECT TEST ITEM" screen.
6.
Touch "HI" on "ACTIVE TEST" screen.
7.
When headlamp high beam is operating, check voltage between
front headlamp RH and LH harness connector and ground.
OK or NG
OK
>> GO TO 8.
NG
>> GO TO 7.
7.
CHECK HEADLAMP CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector E123
terminal 56 and front headlamp RH harness connector E107 ter-
minal 1.
4.
Check continuity between IPDM E/R harness connector E123
terminal 55 and front headlamp LH harness connector E11 ter-
minal 1.
OK or NG
OK
>> Replace IPDM E/R. Refer to
PG-32, "Removal and Installation of IPDM E/R"
NG
>> Repair harness or connector.
8.
CHECK HEADLAMP GROUND
1.
Turn ignition switch OFF.
2.
Check continuity between front headlamp RH harness connec-
tor E107 terminal 2 and ground.
3.
Check continuity between front headlamp LH harness connector
E11 terminal 2 and ground.
OK or NG
OK
>> Check front headlamp connector for damage or poor
connection. Repair as necessary.
NG
>> Repair harness or connector.
Front headlamp
(–)
Voltage
(+)
Connector
Terminal
RH
E107
1
Ground Battery
voltage
LH
E11
WKIA4989E
56 - 1
: Continuity should exist.
55 - 1
: Continuity should exist.
WKIA3498E
2 - Ground
: Continuity should exist.
2 - Ground
: Continuity should exist.
WKIA3499E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст