Nissan Pathfinder (2007 year). Instruction — part 60
CONTROL UNIT
ATC-131
C
D
E
F
G
H
I
K
L
M
A
B
ATC
2007 Pathfinder
CONTROL UNIT
PFP:27500
Removal and Installation
EJS004PL
FRONT AIR CONTROL
Removal
1.
Remove cluster lid C. Refer to
IP-11, "CLUSTER LID C -WITHOUT NAVIGATION SYSTEM"
2.
Remove the four screws securing the front air control to cluster
lid C.
3.
Remove the front air control.
Installation
Installation is in the reverse order of removal.
REAR AIR CONTROL
Removal
1.
Remove the rear finisher assembly from the back of the center console. Refer to
2.
Remove the four screws and remove the rear air control.
Installation
Installation is in the reverse order of removal.
LBIA0416E
LBIA0417E
ATC-132
AMBIENT SENSOR
2007 Pathfinder
AMBIENT SENSOR
PFP:27722
Removal and Installation
EJS004PM
REMOVAL
1.
Remove the front grille. Refer to
2.
Disconnect the ambient sensor 1 (1) electrical connector.
●
⇐
: Front
NOTE:
Both of the ambient sensors are located behind the front grille,
below the hood latch. The upper ambient sensor 1 (1) provides
input for the automatic A/C system. The lower ambient sensor 2
(2) provides input for the compass/temperature driver informa-
tion system.
3.
Release the ambient sensor 1 (1) clip and then remove the
ambient sensor 1 (1).
INSTALLATION
Installation is in the reverse order of removal.
LJIA0192E
IN-VEHICLE SENSOR
ATC-133
C
D
E
F
G
H
I
K
L
M
A
B
ATC
2007 Pathfinder
IN-VEHICLE SENSOR
PFP:27720
Removal and Installation
EJS004PN
REMOVAL
1.
Remove the cluster lid D. Refer to
.
2.
Remove the two screws and remove the in-vehicle sensor.
INSTALLATION
Installation is in the reverse order of removal.
WJIA1073E
ATC-134
OPTICAL SENSOR
2007 Pathfinder
OPTICAL SENSOR
PFP:28576
Removal and Installation
EJS004PO
The optical sensor is located in the top center of the instrument
panel. Refer to
LT-50, "Removal and Installation"
WJIA1072E
INTAKE SENSOR
ATC-135
C
D
E
F
G
H
I
K
L
M
A
B
ATC
2007 Pathfinder
INTAKE SENSOR
PFP:27723
Removal and Installation
EJS004PP
REMOVAL
1.
Remove the front kick plate. Refer to
2.
Remove the lower dash side finisher. Refer to
EI-29, "LOWER DASH SIDE FINISHER"
3.
Remove the front pillar lower finisher. Refer to
EI-29, "FRONT PILLAR LOWER FINISHER"
4.
Remove the assist grip handle.
5.
Remove the front pillar upper finisher. Refer to
EI-29, "FRONT PILLAR UPPER FINISHER"
.
6.
Remove the lower glove box. Refer to
IP-15, "LOWER INSTRUMENT PANEL RH AND LOWER GLOVE
7.
Remove the upper glove box (cluster lid E). Refer to
.
8.
Disconnect the intake sensor electrical connector.
NOTE:
The intake sensor is located on the top of the front heater and
cooling unit assembly next to the A/C evaporator cover.
9.
Twist the intake sensor to remove the intake sensor from the
front heater and cooling unit assembly.
INSTALLATION
Installation is in the reverse order of removal.
LJIA0133E
ATC-136
BLOWER MOTOR
2007 Pathfinder
BLOWER MOTOR
PFP:27226
Components
EJS004PQ
Front Blower Motor
Rear Blower Motor
Removal and Installation
EJS004PR
FRONT BLOWER MOTOR
Removal
1.
Remove the lower glove box assembly. Refer to
IP-15, "LOWER INSTRUMENT PANEL RH AND LOWER
2.
Disconnect the front blower motor electrical connector.
3.
Remove the three screws and remove the front blower motor.
Installation
Installation is in the reverse order of removal.
LJIA0136E
1.
Front heater and cooling unit assembly
2.
Front blower motor
3.
Variable blower control
LJIA0055E
1.
Rear blower motor
2.
Rear blower motor case
3.
Rear blower motor resistor
BLOWER MOTOR
ATC-137
C
D
E
F
G
H
I
K
L
M
A
B
ATC
2007 Pathfinder
REAR BLOWER MOTOR
Removal
1.
Remove the rear heater and cooling unit assembly. Refer to
ATC-142, "REAR HEATER AND COOLING
.
2.
Disconnect the rear blower motor electrical connector.
3.
Remove the three screws and remove the rear blower motor.
Installation
Installation is in the reverse order of removal.
ATC-138
IN-CABIN MICROFILTER
2007 Pathfinder
IN-CABIN MICROFILTER
PFP:27277
Removal and Installation
EJS004PS
FUNCTION
The air inside the passenger compartment is filtered by the in-cabin
microfilters when the heater or A/C controls are set on either the
recirculation or fresh mode. The two in-cabin microfilters are located
in the front heater and cooling unit assembly. The rear heater and
cooling unit assembly only draws in air from the passenger compart-
ment to recirculate into the passenger compartment, so the rear
heater and cooling unit assembly is not equipped with in-cabin
microfilters.
REPLACEMENT TIMING
Replacement of the two in-cabin microfilters is recommended on a regular interval depending on the driving
conditions. Refer to
. It may also be necessary to replace the two in-cabin
microfilters as part of a component replacement if the in-cabin microfilters are damaged.
REPLACEMENT PROCEDURE
1.
Open the lower glove box and press in on the sides so that it will
open completely allowing it to hang by the cord.
2.
Remove the screw and remove the in-cabin microfilter cover.
3.
Remove the in-cabin microfilters from the front heater and cool-
ing unit housing.
4.
Insert the first new in-cabin microfilter into the front heater and
cooling unit housing and slide it over to the right. Insert the sec-
ond new in-cabin microfilter into the front heater and cooling unit
housing.
NOTE:
The in-cabin microfilters are marked with air flow arrows. The
end of the microfilter with the arrow should face the rear of the
vehicle. The arrows should point downward.
LJIA0012E
WLIA0023E
LJIA0134E
LJIA0148E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст