Nissan Pathfinder (2007 year). Instruction — part 270
WINDSHIELD GLASS
GW-13
C
D
E
F
G
H
J
K
L
M
A
B
GW
2007 Pathfinder
1.
Windshield glass
2.
Molding
3.
Roof
4.
Urethane
5.
A-pillar
6.
Primer
7.
Cowl top panel
8.
Insulator
9.
Instrument panel
WIIA1032E
GW-14
WINDSHIELD GLASS
2007 Pathfinder
Repairing Water Leaks for Windshield
Leaks can be repaired without removing and reinstalling glass.
If water is leaking between the urethane adhesive material and body or glass, determine the extent of leakage.
This can be done by applying water to the windshield area while pushing glass outward.
To stop the leak, apply primer (if necessary) and then urethane adhesive to the leak point.
10. Cowl top cover
A.
Primer area (top and sides)
B.
Primer area (bottom)
C.
Bond area (top and sides)
D.
Bond area (bottom)
a.
7.0 mm (0.27 in)
b.
10.0 mm (0.39 in)
c.
22.0 mm (0.78 in)
d.
20.0 mm (0.78 in)
e.
28.0 mm (1.10 in)
f.
12.0 mm (0.47 in)
g.
15.0 mm (0.59 in)
POWER WINDOW SYSTEM
GW-15
C
D
E
F
G
H
J
K
L
M
A
B
GW
2007 Pathfinder
POWER WINDOW SYSTEM
PFP:25401
Component Parts and Harness Connector Location
EIS007RB
System Description
EIS00B70
Power is supplied at all times
●
from 50A fusible link (letter g , located in the fuse and fusible link box)
●
to BCM terminal 70
●
through BCM terminal 69
●
to main power window and door lock/unlock switch terminal 19 and
●
to power window and door lock/unlock switch RH terminal 10.
With ignition switch in ON or START position, power is supplied
●
through 10A fuse [No.1, located in the fuse block (J/B)]
●
to BCM terminal 38
●
through BCM terminal 68
●
to main power window and door lock/unlock switch terminal 10 and
●
to rear power window switch LH and RH terminal 8.
With ignition switch in ACC or ON position, power is supplied
●
through 10A fuse [No. 4, located in the fuse block (J/B)]
●
to BCM terminal 11.
Ground is supplied
●
to BCM terminal 67
1.
Main power window and door lock/
unlock switch D7, D8
2.
BCM M18, M19, M20 (view with
instrument lower panel LH removed)
3.
Power window and door lock/unlock
switch RH D105
4.
Front power window motor LH D9,
RH D104
5.
Front door switch LH B8, RH B108
6.
A. Rear power window switch LH
D203, RH D303
B.Rear power window motor LH
D204, RH D304
LIIA2390E
GW-16
POWER WINDOW SYSTEM
2007 Pathfinder
●
to main power window and door lock/unlock switch terminal 17 and
●
to power window and door lock/unlock switch RH terminal 11
●
through body grounds M57, M61 and M79.
MANUAL OPERATION
Front Door LH
WINDOW UP
When the front LH switch in the main power window and door lock/unlock switch is pulled to the up position,
power is supplied
●
through main power window and door lock/unlock switch terminal 8
●
to front power window motor LH terminal 2.
Ground is supplied
●
through main power window and door lock/unlock switch terminal 11
●
to front power window motor LH terminal 1.
Then, the motor raises the window until the switch is released.
WINDOW DOWN
When the front LH switch in the main power window and door lock/unlock switch is pressed in the down posi-
tion, power is supplied
●
through main power window and door lock/unlock switch terminal 11
●
to front power window motor LH terminal 1.
Ground is supplied
●
through main power window and door lock/unlock switch terminal 8
●
to front power window motor LH terminal 2.
Then, the motor lowers the window until the switch is released.
Front Door RH
POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH OPERATION
WINDOW UP
When the power window and door lock/unlock switch RH is pulled to the up position, power is supplied
●
through power window and door lock/unlock switch RH terminal 8
●
to front power window motor RH terminal 2.
Ground is supplied
●
through power window and door lock/unlock switch RH terminal 9
●
to front power window motor RH terminal 1.
Then, the motor raises the window until the switch is released.
WINDOW DOWN
When the power window and door lock/unlock switch RH is pressed in the down position, power is supplied
●
through power window and door lock/unlock switch RH terminal 9
●
to front power window motor RH terminal 1.
Ground is supplied
●
through power window and door lock/unlock switch RH terminal 8
●
to front power window motor RH terminal 2.
Then, the motor lowers the window until the switch is released.
MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OPERATION
Signal is sent
●
though main power window and door lock/unlock switch terminal 14
●
to power window and door lock/unlock switch RH terminal 16.
The operation of power window after receiving the signal is the same as operating the power window with
power window and door lock/unlock switch RH.
Rear Door LH or RH
REAR POWER WINDOW SWITCH LH OR RH OPERATION
WINDOW UP
When the rear power window switch LH or RH is pulled to the up position, power is supplied
POWER WINDOW SYSTEM
GW-17
C
D
E
F
G
H
J
K
L
M
A
B
GW
2007 Pathfinder
●
through rear power window switch LH or RH terminal 7
●
to rear power window motor LH or RH terminal 2.
Ground is supplied
●
through rear power window switch LH or RH terminal 6
●
to rear power window motor LH or RH terminal 1.
Then, the motor raises the window until the switch is released.
WINDOW DOWN
When the rear power window switch LH or RH is pressed in the down position, power is supplied
●
through rear power window switch LH or RH terminal 6
●
to rear power window motor LH or RH terminal 1.
Ground is supplied
●
through rear power window switch LH or RH terminal 7
●
to rear power window motor LH or RH terminal 2.
Then, the motor lowers the window until the switch is released.
MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OPERATION
WINDOW UP
When the main power window and door lock/unlock switch (rear LH) is pressed in the up position, power is
supplied
●
through main power window and door lock/unlock switch terminal 1
●
to rear power window switch LH terminal 4
●
through rear power window switch LH terminal 7
●
to rear power window motor LH terminal 2.
Ground is supplied
●
to main power window and door lock/unlock switch terminal 17
●
through main power window and door lock/unlock switch terminal 3
●
to rear power window switch LH terminal 5
●
through rear power window switch LH terminal 6
●
to rear power window motor LH terminal 1.
Then, the motor raises the window until the switch is released.
When the main power window and door lock/unlock switch (rear RH) is pulled to the up position, power is sup-
plied
●
through main power window and door lock/unlock switch terminal 7
●
to rear power window switch RH terminal 4
●
through rear power window switch RH terminal 7
●
to rear power window motor RH terminal 2.
Ground is supplied
●
to main power window and door lock/unlock switch terminal 17
●
through main power window and door lock/unlock switch terminal 5
●
to rear power window switch LH terminal 5
●
through rear power window switch LH terminal 6
●
to rear power window motor LH terminal 1.
Then, the motor raises the window until the switch is released.
WINDOW DOWN
When the main power window and door lock/unlock switch (rear LH) is pressed in the down position, power is
supplied
●
through main power window and door lock/unlock switch terminal 3
●
to rear power window switch LH terminal 5
●
through rear power window switch LH terminal 6
●
to rear power window motor LH terminal 1.
Ground is supplied
●
to main power window and door lock/unlock switch terminal 17
GW-18
POWER WINDOW SYSTEM
2007 Pathfinder
●
through main power window and door lock/unlock switch terminal 1
●
to rear power window switch LH terminal 4
●
through rear power window switch LH terminal 7
●
to rear power window motor LH terminal 2.
Then, the motor lowers the window until the switch is released.
When the main power window and door lock/unlock switch (rear RH) is pressed in the down position, power is
supplied
●
through main power window and door lock/unlock switch terminal 5
●
to rear power window switch RH terminal 5
●
through rear power window switch RH terminal 6
●
to rear power window motor RH terminal 1.
Ground is supplied
●
to main power window and door lock/unlock switch terminal 17
●
through main power window and door lock/unlock switch terminal 7
●
to rear power window switch LH terminal 4
●
through rear power window switch LH terminal 7
●
to rear power window motor LH terminal 2.
Then, the motor lowers the window until the switch is released.
AUTO OPERATION
The power window AUTO feature allows the driver to open or close the front window LH or RH and the pas-
senger to open or close the front window RH without holding the window switch in the down or up position.
POWER WINDOW SERIAL LINK
Main power window and door lock/unlock switch, power window and door lock/unlock switch RH, and BCM
transmit and receive the signal by power window serial link.
●
Front door window RH operation signal.
●
Power window control by front door lock assembly LH (key cylinder switch) signal.
●
Power window lock signal.
●
Retained power operation signal.
The signal is transmitted from main power window and door lock/unlock switch to power window and door
lock/unlock switch RH.
POWER WINDOW LOCK
The power window lock is designed to lock operation of all windows except for front door window LH.
When in the lock position, ground of the rear LH and RH power window switches in the main power window
and door lock/unlock switch is disconnected. The power window lock signal is transmitted to front power win-
dow switch RH by power window serial link. This prevents the power window motors from operating.
RETAINED POWER OPERATION
When the ignition switch is turned to the OFF position from ON or START position
Power is supplied for 45 seconds
●
to main power window and door lock/unlock switch terminal 10 and
●
to rear power window switch (LH and RH) terminal 8
●
from BCM terminal 68.
When power and ground are supplied, the BCM continues to be energized, and the power window can be
operated.
The retained power operation is canceled when the front LH or front RH door is opened.
RAP signal period can be changed by CONSULT-II. Refer to
GW-28, "CONSULT-II Function (BCM)"
ANTI-PINCH SYSTEM
Main power window and door lock/unlock switch and power window and door lock/unlock switch RH monitor
the power window motor operation and the power window position (full closed or other) for front LH and front
RH power window by the signals from encoder and limit switch in front power window motor LH and RH.
When main power window and door lock/unlock switch or power window and door lock/unlock switch RH
detects interruption during the following close operation,
POWER WINDOW SYSTEM
GW-19
C
D
E
F
G
H
J
K
L
M
A
B
GW
2007 Pathfinder
●
automatic close operation when ignition switch is in the ON position
●
automatic close operation during retained power operation
Main power window and door lock/unlock switch or power window and door lock/unlock switch RH controls
each front power window motor for open and the power window will be lowered.
POWER WINDOW CONTROL BY THE KEY CYLINDER SWITCH
When ignition switch is OFF, front power window LH and RH can be opened or closed by turning the front door
lock assembly LH (key cylinder switch) to the UNLOCK/LOCK position for more than 1 second.
●
Front power windows can be opened as the door key cylinder is kept fully turned to the UNLOCK position.
●
Front power windows can be closed as the door key cylinder is kept fully turned to the LOCK position.
The power window opening stops when the following operations are carried out.
●
While performing open/close operation for the windows, power window is stopped when the door key cyl-
inder is placed in the NEUTRAL position.
●
When the ignition switch is turned ON while the power window opening operation is performed.
CAN Communication System Description
EIS007RD
Refer to
GW-20
POWER WINDOW SYSTEM
2007 Pathfinder
Schematic
EIS007RE
WIWA2110E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст