Nissan Pathfinder (2007 year). Instruction — part 213
DTC P2101 ELECTRIC THROTTLE CONTROL FUNCTION
EC-571
C
D
E
F
G
H
I
J
K
L
M
A
EC
2007 Pathfinder
10.
CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1.
Remove the intake air duct.
2.
Check if foreign matter is caught between the throttle valve and
the housing.
OK or NG
OK
>> GO TO 11.
NG
>> Remove the foreign matter and clean the electric throttle
control actuator inside.
11.
CHECK THROTTLE CONTROL MOTOR
Refer to
EC-571, "Component Inspection"
OK or NG
OK
>> GO TO 12.
NG
>> GO TO 13.
12.
CHECK INTERMITTENT INCIDENT
Refer to
EC-145, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
OK or NG
OK
>> GO TO 13.
NG
>> Repair or replace harness or connectors.
13.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace the electric throttle control actuator.
2.
Perform
EC-77, "Throttle Valve Closed Position Learning"
.
3.
Perform
EC-77, "Idle Air Volume Learning"
.
>> INSPECTION END
Component Inspection
UBS00KCA
THROTTLE CONTROL MOTOR
1.
Disconnect electric throttle control actuator harness connector.
2.
Check resistance between terminals 5 and 6.
3.
If NG, replace electric throttle control actuator and go to next
step.
4.
Perform
EC-77, "Throttle Valve Closed Position Learning"
.
5.
Perform
EC-77, "Idle Air Volume Learning"
.
Removal and Installation
UBS00KCB
ELECTRIC THROTTLE CONTROL ACTUATOR
Refer to
EM-17, "INTAKE MANIFOLD COLLECTOR"
.
BBIA0554E
Resistance: Approximately 1 - 15
Ω
[at 25
°
C (77
°
F)]
PBIB2606E
EC-572
DTC P2118 THROTTLE CONTROL MOTOR
2007 Pathfinder
DTC P2118 THROTTLE CONTROL MOTOR
PFP:16119
Component Description
UBS00KCI
The throttle control motor is operated by the ECM and it opens and closes the throttle valve.
The current opening angle of the throttle valve is detected by the throttle position sensor and it provides feed-
back to the ECM to control the throttle control motor to make the throttle valve opening angle properly in
response to driving condition.
On Board Diagnosis Logic
UBS00KCJ
This self-diagnosis has the one trip detection logic.
FAIL-SAFE MODE
When the malfunction is detected, the ECM enters fail-safe mode and the MIL lights up.
DTC Confirmation Procedure
UBS00KCK
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON and wait at least 2 seconds.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Start engine and let it idle for 5 seconds.
4.
If DTC is detected, go to
EC-574, "Diagnostic Procedure"
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P2118
2118
Throttle control motor
circuit short
ECM detects short in both circuits between
ECM and throttle control motor.
●
Harness or connectors
(Throttle control motor circuit is shorted.)
●
Electric throttle control actuator
(Throttle control motor)
Engine operating condition in fail-safe mode
ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return
spring.
SEF058Y
DTC P2118 THROTTLE CONTROL MOTOR
EC-573
C
D
E
F
G
H
I
J
K
L
M
A
EC
2007 Pathfinder
Wiring Diagram
UBS00KCL
BBWA1761E
EC-574
DTC P2118 THROTTLE CONTROL MOTOR
2007 Pathfinder
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
Diagnostic Procedure
UBS00KCM
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten three ground screws on the body. Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connections.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
3
V
Throttle control motor relay
power supply
[Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14V)
4
L/W
Throttle control motor
(Close)
[Ignition switch: ON]
●
Engine: Stopped
●
Shift lever: D
●
Accelerator pedal: Fully released
0 - 14V
5
L/B
Throttle control motor
(Open)
[Ignition switch: ON]
●
Engine: Stopped
●
Shift lever: D
●
Accelerator pedal: Fully depressed
0 - 14V
104
O
Throttle control motor relay
[Ignition switch: OFF]
BATTERY VOLTAGE
(11 - 14V)
[Ignition switch: ON]
0 - 1.0V
PBIB1104E
PBIB1105E
BBIA0539E
DTC P2118 THROTTLE CONTROL MOTOR
EC-575
C
D
E
F
G
H
I
J
K
L
M
A
EC
2007 Pathfinder
2.
CHECK THROTTLE CONTROL MOTOR OUTPUT SIGNAL CIRCUIT FOR OPEN OR SHORT
1.
Disconnect electric throttle control actuator harness connector.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between the following terminals.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace.
3.
CHECK THROTTLE CONTROL MOTOR
Refer to
EC-575, "Component Inspection"
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 5.
4.
CHECK INTERMITTENT INCIDENT
Refer to
EC-145, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace harness or connectors.
5.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace the electric throttle control actuator.
2.
Perform
EC-77, "Throttle Valve Closed Position Learning"
.
3.
Perform
EC-77, "Idle Air Volume Learning"
.
>> INSPECTION END
Component Inspection
UBS00KCN
THROTTLE CONTROL MOTOR
1.
Disconnect electric throttle control actuator harness connector.
2.
Check resistance between terminals 5 and 6.
3.
If NG, replace electric throttle control actuator and go to next
step.
4.
Perform
EC-77, "Throttle Valve Closed Position Learning"
.
5.
Perform
EC-77, "Idle Air Volume Learning"
.
Electric throttle control
actuator terminal
ECM terminal
Continuity
5
5
Should not exist
4
Should exist
6
5
Should exist
4
Should not exist
BBIA0543E
Resistance: Approximately 1 - 15
Ω
[at 25
°
C (77
°
F)]
PBIB2606E
EC-576
DTC P2118 THROTTLE CONTROL MOTOR
2007 Pathfinder
Removal and Installation
UBS00KCO
ELECTRIC THROTTLE CONTROL ACTUATOR
Refer to
DTC P2119 ELECTRIC THROTTLE CONTROL ACTUATOR
EC-577
C
D
E
F
G
H
I
J
K
L
M
A
EC
2007 Pathfinder
DTC P2119 ELECTRIC THROTTLE CONTROL ACTUATOR
PFP:16119
Component Description
UBS00KC1
Electric throttle control actuator consists of throttle control motor, throttle position sensor, etc.
The throttle control motor is operated by the ECM and it opens and closes the throttle valve.
The throttle position sensor detects the throttle valve position, and the opening and closing speed of the throt-
tle valve and feeds the voltage signals to the ECM. The ECM judges the current opening angle of the throttle
valve from these signals and the ECM controls the throttle control motor to make the throttle valve opening
angle properly in response to driving condition.
On Board Diagnosis Logic
UBS00KC2
This self-diagnosis has the one trip detection logic.
FAIL-SAFE MODE
When the malfunction is detected, the ECM enters fail-safe mode and the MIL lights up.
DTC Confirmation Procedure
UBS00KC3
NOTE:
●
Perform PROCEDURE FOR MALFUNCTION A AND B first. If the DTC cannot be confirmed, perform
PROCEDURE FOR MALFUNCTION C.
●
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait
at least 10 seconds before conducting the next test.
PROCEDURE FOR MALFUNCTION A AND B
With CONSULT-II
1.
Turn ignition switch ON and wait at least 1 second.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Shift selector lever to D position and wait at least 3 seconds.
4.
Shift selector lever to P position.
5.
Turn ignition switch OFF and wait at least 10 seconds.
6.
Turn ignition switch ON and wait at least 1 second.
7.
Shift selector lever to D position, and wait at least 3 seconds.
8.
Shift selector lever to P position.
9.
Turn ignition switch OFF, wait at least 10 seconds, and then turn
ON.
10. If DTC is detected, go to
EC-578, "Diagnostic Procedure"
With GST
Follow the procedure “With CONSULT-II” above.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P2119
2119
Electric throttle control
actuator
A)
Electric throttle control actuator does not func-
tion properly due to the return spring malfunc-
tion.
●
Electric throttle control actuator
B)
Throttle valve opening angle in fail-safe mode is
not in specified range.
C)
ECM detect the throttle valve is stuck open.
Detected items
Engine operating condition in fail-safe mode
Malfunction A
The ECM controls the electric throttle actuator by regulating the throttle opening around the idle position.
The engine speed will not rise more than 2,000 rpm.
Malfunction B
ECM controls the electric throttle control actuator by regulating the throttle opening to 20 degrees or less.
Malfunction C
While the vehicle is driving, it slows down gradually by fuel cut. After the vehicle stops, the engine stalls.
The engine can restart in N or P position, and engine speed will not exceed 1,000 rpm or more.
SEF058Y
EC-578
DTC P2119 ELECTRIC THROTTLE CONTROL ACTUATOR
2007 Pathfinder
PROCEDURE FOR MALFUNCTION C
With CONSULT-II
1.
Turn ignition switch ON and wait at least 1 second.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Shift selector lever to D position and wait at least 3 seconds.
4.
Shift selector lever to P or N position.
5.
Start engine and let it idle for 3 seconds.
6.
If DTC is detected, go to
EC-578, "Diagnostic Procedure"
.
With GST
Follow the procedure “With CONSULT-II” above.
Diagnostic Procedure
UBS00KC4
1.
CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1.
Remove the intake air duct.
2.
Check if a foreign matter is caught between the throttle valve
and the housing.
OK or NG
OK
>> GO TO 2.
NG
>> Remove the foreign matter and clean the electric throttle
control actuator inside.
2.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace the electric throttle control actuator.
2.
Perform
EC-77, "Throttle Valve Closed Position Learning"
.
3.
Perform
EC-77, "Idle Air Volume Learning"
>> INSPECTION END
SEF058Y
BBIA0554E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст