Nissan Pathfinder (2007 year). Instruction — part 168
DTC P0117, P0118 ECT SENSOR
EC-211
C
D
E
F
G
H
I
J
K
L
M
A
EC
2007 Pathfinder
Diagnostic Procedure
UBS00K61
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten three ground screws on the body. Refer to
.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connections.
2.
CHECK ECT SENSOR POWER SUPPLY CIRCUIT
1.
Disconnect engine coolant temperature (ECT) sensor harness
connector.
2.
Turn ignition switch ON.
3.
Check voltage between ECT sensor terminal 1 and ground with
CONSULT-II or tester.
OK or NG
OK
>> GO TO 3.
NG
>> Repair open circuit or short to ground or short to power
in harness or connectors.
BBIA0539E
BBIA0542E
Voltage: Approximately 5V
PBIB0080E
EC-212
DTC P0117, P0118 ECT SENSOR
2007 Pathfinder
3.
CHECK ECT SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between ECT sensor terminal 2 and ECM terminal 67.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.
CHECK ENGINE COOLANT TEMPERATURE SENSOR
Refer to
EC-212, "Component Inspection"
OK or NG
OK
>> GO TO 5.
NG
>> Replace engine coolant temperature sensor.
5.
CHECK INTERMITTENT INCIDENT
Refer to
EC-145, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Component Inspection
UBS00K62
ENGINE COOLANT TEMPERATURE SENSOR
1.
Check resistance between engine coolant temperature sensor
terminals 1 and 2 as shown in the figure.
<Reference data>
2.
If NG, replace engine coolant temperature sensor.
Removal and Installation
UBS00K63
ENGINE COOLANT TEMPERATURE SENSOR
Refer to
CO-24, "WATER INLET AND THERMOSTAT ASSEMBLY"
Continuity should exist.
PBIB2005E
Engine coolant temperature
°
C (
°
F)
Resistance
k
Ω
20 (68)
2.1 - 2.9
50 (122)
0.68 - 1.00
90 (194)
0.236 - 0.260
SEF012P
DTC P0122, P0123 TP SENSOR
EC-213
C
D
E
F
G
H
I
J
K
L
M
A
EC
2007 Pathfinder
DTC P0122, P0123 TP SENSOR
PFP:16119
Component Description
UBS00K64
Electric throttle control actuator consists of throttle control motor,
throttle position sensor, etc. The throttle position sensor responds to
the throttle valve movement.
The throttle position sensor has the two sensors. These sensors are
a kind of potentiometers which transform the throttle valve position
into output voltage, and emit the voltage signal to the ECM. In addi-
tion, these sensors detect the opening and closing speed of the
throttle valve and feed the voltage signals to the ECM. The ECM
judges the current opening angle of the throttle valve from these sig-
nals and the ECM controls the throttle control motor to make the
throttle valve opening angle properly in response to driving condi-
tion.
CONSULT-II Reference Value in Data Monitor Mode
UBS00K65
Specification data are reference values.
*: Throttle position sensor 2 signal is converted by ECM internally. Thus, it differs from ECM terminal voltage signal.
On Board Diagnosis Logic
UBS00K66
These self-diagnoses have the one trip detection logic.
FAIL-SAFE MODE
When the malfunction is detected, ECM enters fail-safe mode and the MIL lights up.
PBIB0145E
MONITOR ITEM
CONDITION
SPECIFICATION
THRTL SEN 1
THRTL SEN 2*
●
Ignition switch: ON
(Engine stopped)
●
Shift lever: D
Accelerator pedal: Fully released
More than 0.36V
Accelerator pedal: Fully depressed
Less than 4.75V
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0122
0122
Throttle position sensor
2 circuit low input
An excessively low voltage from the TP sensor
2 is sent to ECM.
●
Harness or connectors
(The TP sensor 2 circuit is open or
shorted.)
(The APP sensor 2 circuit is shorted.)
●
Electric throttle control actuator
(TP sensor 2)
●
Accelerator pedal position sensor
(APP sensor 2)
P0123
0123
Throttle position sensor
2 circuit high input
An excessively high voltage from the TP sen-
sor 2 is sent to ECM.
Engine operation condition in fail-safe mode
The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle position to be within +10
degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal condition.
So, the acceleration will be poor.
EC-214
DTC P0122, P0123 TP SENSOR
2007 Pathfinder
DTC Confirmation Procedure
UBS00K67
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10V at idle.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Start engine and let it idle for 1 second.
4.
If DTC is detected, go to
EC-216, "Diagnostic Procedure"
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
SEF058Y
DTC P0122, P0123 TP SENSOR
EC-215
C
D
E
F
G
H
I
J
K
L
M
A
EC
2007 Pathfinder
Wiring Diagram
UBS00K68
BBWA1745E
EC-216
DTC P0122, P0123 TP SENSOR
2007 Pathfinder
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
Diagnostic Procedure
UBS00K69
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten three ground screws on the body. Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connections.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
47
L
Sensor power supply
(Throttle position sensor)
[Ignition switch: ON]
Approximately 5V
50
W
Throttle position sensor 1
[Ignition switch: ON]
●
Engine: Stopped
●
Shift lever: D
●
Accelerator pedal: Fully released
More than 0.36V
[Ignition switch: ON]
●
Engine: Stopped
●
Shift lever: D
●
Accelerator pedal: Fully depressed
Less than 4.75V
66
B
Sensor ground
(Throttle position sensor)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 0V
69
R
Throttle position sensor 2
[Ignition switch: ON]
●
Engine: Stopped
●
Shift lever: D
●
Accelerator pedal: Fully released
Less than 4.75V
[Ignition switch: ON]
●
Engine: Stopped
●
Shift lever: D
●
Accelerator pedal: Fully depressed
More than 0.36V
91
G
Sensor power supply
(APP sensor 2)
[Ignition switch: ON]
Approximately 5V
BBIA0539E
DTC P0122, P0123 TP SENSOR
EC-217
C
D
E
F
G
H
I
J
K
L
M
A
EC
2007 Pathfinder
2.
CHECK THROTTLE POSITION SENSOR 2 POWER SUPPLY CIRCUIT-I
1.
Disconnect electric throttle control actuator harness connector.
2.
Turn ignition switch ON.
3.
Check voltage between electric throttle control actuator terminal
2 and ground with CONSULT-II or tester.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 3.
3.
CHECK THROTTLE POSITION SENSOR 2 POWER SUPPLY CIRCUIT-II
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between electric throttle control actuator terminal 2 and ECM terminal 47.
Refer to Wiring Diagram.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit.
4.
CHECK THROTTLE POSITION SENSOR 2 POWER SUPPLY CIRCUIT-III
Check harness for short to power and short to ground, between the following terminals.
OK or NG
OK
>> GO TO 5.
NG
>> Repair short to ground or short to power in harness or connectors.
5.
CHECK APP SENSOR
Refer to
EC-591, "Component Inspection"
OK or NG
OK
>> GO TO 11.
NG
>> GO TO 6.
BBIA0543E
Voltage: Approximately 5V
PBIB2604E
Continuity should exist.
ECM terminal
Sensor terminal
Reference Wiring Diagram
47
Electric throttle control actuator terminal 2
91
APP sensor terminal 1
EC-218
DTC P0122, P0123 TP SENSOR
2007 Pathfinder
6.
REPLACE ACCELERATOR PEDAL ASSEMBLY
1.
Replace accelerator pedal assembly.
2.
Perform
EC-77, "Accelerator Pedal Released Position Learning"
3.
Perform
EC-77, "Throttle Valve Closed Position Learning"
.
4.
Perform
EC-77, "Idle Air Volume Learning"
>> INSPECTION END
7.
CHECK THROTTLE POSITION SENSOR 2 GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between electric throttle control actuator terminal 4 and ECM terminal 66.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 8.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
8.
CHECK THROTTLE POSITION SENSOR 2 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check harness continuity between ECM terminal 69 and electric throttle control actuator terminal 3.
Refer to Wiring Diagram.
2.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 9.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
9.
CHECK THROTTLE POSITION SENSOR
Refer to
EC-219, "Component Inspection"
OK or NG
OK
>> GO TO 11.
NG
>> GO TO 10.
10.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace the electric throttle control actuator.
2.
Perform
EC-77, "Throttle Valve Closed Position Learning"
.
3.
Perform
EC-77, "Idle Air Volume Learning"
>> INSPECTION END
11.
CHECK INTERMITTENT INCIDENT
Refer to
EC-145, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Continuity should exist.
Continuity should exist.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст