Nissan Primera P11. Instruction — part 145
Component Inspection
NLEC0102
HEATED OXYGEN SENSOR 1 (FRONT)
NLEC0102S01
With CONSULT-II
1)
Start engine and warm it up to normal operating temperature.
2)
Select “MANU TRIG” in “DATA MONITOR” mode, and select
“HO2S1 (B1)” and “HO2S1 MNTR (B1)”.
3)
Hold engine speed at 2,000 rpm under no load during the fol-
lowing steps.
4)
Touch “RECORD” on CONSULT-II screen.
5)
Check the following.
I
“HO2S1 MNTR (B1)” in “DATA MONITOR” mode changes from
“RICH” to “LEAN” to “RICH” 5 times in 10 seconds.
5 times (cycles) are counted as shown below:
R = “HO2S1 MNTR (B1)”, “RICH”
L = “HO2S1 MNTR (B1)”, “LEAN”
I
“HO2S1 (B1)” voltage goes above 0.6V at least once.
I
“HO2S1 (B1)” voltage goes below 0.3V at least once.
I
“HO2S1 (B1)” voltage never exceeds 1.0V.
CAUTION:
I
Discard any heated oxygen sensor which has been
dropped from a height of more than 0.5 m (19.7 in) onto a
hard surface such as a concrete floor; use a new one.
I
Before installing new oxygen sensor, clean exhaust sys-
tem threads using Oxygen Sensor Thread Cleaner tool
and approved anti-seize lubricant.
Without CONSULT-II
1)
Start engine and warm it up to normal operating temperature.
2)
Set voltmeter probes between ECM terminal 62 (HO2S1 sig-
nal) and engine ground.
3)
Check the following with engine speed held at 2,000 rpm con-
stant under no load.
I
Malfunction indicator goes on more than five times within 10
seconds in Diagnostic Test Mode II [HEATED OXYGEN SEN-
SOR 1 MONITOR (FRONT).]
I
The maximum voltage is over 0.6V at least one time.
I
The minimum voltage is below 0.3V at least one time.
SEF646Y
SEF647Y
SEF648Y
SEF011X
DTC P0130 HEATED OXYGEN SENSOR 1 (FRONT)
(CIRCUIT)
QG16
I
18DE
Component Inspection
EC-137
I
The voltage never exceeds 1.0V.
CAUTION:
I
Discard any heated oxygen sensor which has been
dropped from a height of more than 0.5 m (19.7 in) onto a
hard surface such as a concrete floor; use a new one.
I
Before installing new oxygen sensor, clean exhaust sys-
tem threads using Oxygen Sensor Thread Cleaner tool
and approved anti-seize lubricant.
DTC P0130 HEATED OXYGEN SENSOR 1 (FRONT)
(CIRCUIT)
QG16
I
18DE
Component Inspection (Cont’d)
EC-138
Component Description
NLEC0103
The heated oxygen sensor 1 (front) is placed into the exhaust
manifold. It detects the amount of oxygen in the exhaust gas com-
pared to the outside air. The heated oxygen sensor 1 (front) has a
closed-end tube made of ceramic zirconia. The zirconia generates
voltage from approximately 1V in richer conditions to 0V in leaner
conditions. The heated oxygen sensor 1 (front) signal is sent to the
ECM. The ECM adjusts the injection pulse duration to achieve the
ideal air-fuel ratio. The ideal air-fuel ratio occurs near the radical
change from 1V to 0V.
CONSULT-II Reference Value in Data Monitor
Mode
NLEC0104
Specification data are reference values.
MONITOR ITEM
CONDITION
SPECIFICATION
HO2S1 (B1)
I
Engine: After warming up
Maintaining engine speed at 2,000
rpm
0 - 0.3V
+,
Approx. 0.6 - 1.0V
HO2S1 MNTR
(B1)
LEAN
+,
RICH
Changes more than 5 times during
10 seconds.
ECM Terminals and Reference Value
NLEC0105
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM’s transistor. Use a ground other than ECM terminals, such as the ground.
TERMI-
NAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
62
R
Heated oxygen sensor
1 (front)
[Engine is running]
I
After warming up to normal operating temperature
and engine speed is 2,000 rpm
0 - Approximately 1.0V
SEF008W
SEF463R
SEF288D
DTC P0131 HEATED OXYGEN SENSOR 1 (FRONT)
(LEAN SHIFT MONITORING)
QG16
I
18DE
Component Description
EC-139
On Board Diagnosis Logic
NLEC0106
To judge the malfunction, the output from the heated oxygen sen-
sor 1 (front) is monitored to determine whether the “rich” output is
sufficiently high and whether the “lean” output is sufficiently low.
When both the outputs are shifting to the lean side, the malfunc-
tion will be detected.
DTC No.
Malfunction is detected when ...
Check Items (Possible Cause)
P0131
0131
I
The maximum and minimum voltages from the sensor
are not reached to the specified voltages.
I
Heated oxygen sensor 1 (front)
I
Heated oxygen sensor 1 heater (front)
I
Fuel pressure
I
Injectors
I
Intake air leaks
DTC Confirmation Procedure
NLEC0107
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously conducted,
always turn ignition switch “OFF” and wait at least 9 seconds
before conducting the next test.
TESTING CONDITION:
I
Always perform at a temperature above −10°C (14°F).
I
Before performing the following procedure, confirm that
battery voltage is more than 11V at idle.
With CONSULT-II
1)
Start engine and warm it up to normal operating temperature.
2)
Stop engine and wait at least 9 seconds.
3)
Turn ignition switch “ON” and select “HO2S1 (B1) P0131” of
“HO2S1” in “DTC WORK SUPPORT” mode with CONSULT-II.
4)
Touch “START”.
5)
Start engine and let it idle for at least 3 minutes.
NOTE:
Never raise engine speed above 3,200 rpm after this step. If
the engine speed limit is exceeded, return to step 5.
6)
When the following conditions are met, “TESTING” will be dis-
played on the CONSULT-II screen. Maintain the conditions
continuously until “TESTING” changes to “COMPLETED”. (It
will take approximately 50 seconds or more.)
SEF300U
SEF827Y
SEF828Y
SEF651Y
DTC P0131 HEATED OXYGEN SENSOR 1 (FRONT)
(LEAN SHIFT MONITORING)
QG16
I
18DE
On Board Diagnosis Logic
EC-140
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст