Nissan Primera P11. Instruction — part 392
21. Install camshaft sprocket bolts to correct torque.
I
Apply new engine oil to bolt threads and seat surface.
22. Install chain tensioner.
I
Before installing chain tensioner, insert a suitable pin into
pin hole of chain tensioner.
I
After installing chain tensioner, remove the pin.
23. Install timing chain guide.
24. Install cylinder head front cover.
I
Apply liquid gasket to cylinder head front cover.
I
Use Genuine Liquid Gasket or equivalent.
25. Install camshaft position sensor (PHASE).
26. Before installing rocker cover, apply a continuous bead of li-
quid gasket to mating surface of cylinder head.
SEM906F
SEM907F
Chain guide
Chain tensioner
Stopper pin
SEM887F
Cylinder head front cover
2.0 - 3.0 mm
(0.079 -
0.118 in) dia.
SEM889F
Camshaft position
sensor (PHASE)
O-ring
SEM888F
Liquid gasket
3 mm (0.12 in) dia.
Cylinder head
Cylinder head front cover
TIMING CHAIN
QG
Installation (Cont’d)
EM-27
27. Install rocker cover and tighten bolts in numerical order as
shown in the figure.
28. Install spark plugs.
29. Install ignition coils.
30. Install engine front mounting.
31. Install front exhaust tube.
32. Install front undercover.
33. Install front right splash cover.
34. Install front right wheel.
35. Install power steering pulley and pump with bracket.
To check power steering fluid, refer to MA section (“Checking
Power Steering Fluid and Lines”, “CHASSIS AND BODY
MAINTENANCE”).
36. Drive belts.
For adjusting drive belt deflection, refer to MA section (“Check-
ing Drive Belts”, “ENGINE MAINTENANCE”).
37. Reinstall parts in reverse order of removal.
SEM908F
Tighten in numerical order
TIMING CHAIN
QG
Installation (Cont’d)
EM-28
Replacement
NCEM0015
VALVE OIL SEAL
NCEM0015S01
1.
Remove rocker cover.
2.
Remove camshaft.
3.
Remove valve spring. Refer to EM-34.
4.
Remove valve oil seal with Tool.
Piston concerned should be set at TDC to prevent valve from
falling.
5.
Apply new engine oil to new valve oil seal and install it with
Tool.
FRONT OIL SEAL
NCEM0015S02
1.
Remove the following parts:
I
Engine under cover
I
RH engine side cover
I
Generator and power steering drive belts
I
Crankshaft pulley
2.
Remove front oil seal from front cover.
I
Be careful not to scratch front cover.
3.
Apply new engine oil to new oil seal and install it using a suit-
able tool.
I
Install new oil seal in the direction shown.
SEM909F
KV10107902
SEM910F
13.5±
0.3 mm
(0.531±
0.012 in)
KV10115600
SEM911F
Front oil seal
SEM715A
Engine
outside
Dust seal lip
Engine
inside
Oil seal lip
SEM912F
Suitable tool
OIL SEAL
QG
Replacement
EM-29
REAR OIL SEAL
NCEM0015S03
1.
Remove flywheel or drive plate.
2.
Remove rear oil seal.
I
Be careful not to scratch rear oil seal retainer.
3.
Apply new engine oil to new oil seal and install it using a suit-
able tool.
I
Install new oil seal in the direction shown.
SEM096F
SEM715A
Engine
outside
Dust seal lip
Oil seal lip
Engine
inside
SEM097F
Suitable tool
OIL SEAL
QG
Replacement (Cont’d)
EM-30
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст