Nissan Primera P11. Instruction — part 280
3
DETECT MALFUNCTIONING PART
Check the following.
I
15A fuse
I
Harness for open or short between fuse and fuel pump relay
©
Repair harness or connectors.
4
CHECK POWER GROUND CIRCUIT
1. Turn ignition switch “OFF”.
2. Disconnect fuel pump harness connector.
SEF299W
3. Check harness continuity between fuel pump harness connector terminal 2 and body ground, terminal 1 and fuel pump relay connector
terminal 9J.
Refer to wiring diagram.
Continuity should exist.
4. Also check harness for short to ground and short to power.
OK or NG
OK
©
GO TO 6.
NG
©
GO TO 5.
5
DETECT MALFUNCTIONING PART
Check the following.
I
Harness for open or short between fuel pump and body ground
I
Harness for open or short between fuel pump and fuel pump relay
©
Repair open circuit or short to ground or short to power in harness or connectors.
6
CHECK OUTPUT SIGNAL CIRCUIT
1. Disconnect ECM harness connector.
2. Check harness continuity between ECM terminal 21 and fuel pump relay connector terminal 19C.
Refer to wiring diagram.
Continuity should exist.
3. Also check harness for short to ground and short to power.
OK or NG
OK
©
GO TO 8.
NG
©
GO TO 7.
7
DETECT MALFUNCTIONING PART
Check the following.
I
Harness connectors M50, F104 (CVT: M81, F115)
I
Harness for open or short between ECM and fuel pump relay
NG
©
Repair open circuit or short to ground or short to power in harness or connectors.
FUEL PUMP
SR20DE
Diagnostic Procedure (Cont’d)
EC-319
Component Inspection
NCEC0449
FUEL PUMP RELAY
NCEC0449S01
Check continuity between terminals 3 and 5.
Conditions
Continuity
12V direct current supply between terminals 1 and 2
Yes
No current supply
No
If NG, replace relay.
FUEL PUMP
NCEC0449S02
1.
Disconnect fuel pump harness connector.
2.
Check resistance between terminals 1 and 2.
Resistance: 0.2 - 5.0
Ω
[at 25°C (77°F)]
If NG, replace fuel pump.
8
CHECK FUEL PUMP RELAY
Refer to “Component Inspection”, EC-SR-320.
OK or NG
OK
©
GO TO 9.
NG
©
Replace fuel pump relay.
9
CHECK FUEL PUMP
Refer to “Component Inspection”, EC-SR-320.
OK or NG
OK
©
GO TO 10.
NG
©
Replace fuel pump.
10
CHECK INTERMITTENT INCIDENT
Perform “TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT”, EC-SR-114.
©
INSPECTION END
SEF145X
SEF326W
FUEL PUMP
SR20DE
Component Inspection
EC-320
Component Description
NCEC0451
The power steering oil pressure switch is attached to the power
steering high-pressure tube and detects a power steering load.
When a power steering load is detected, it signals the ECM. The
ECM adjusts the IACV-AAC valve to increase the idle speed and
adjust for the increased load.
CONSULT-II Reference Value in Data Monitor
Mode
NCEC0452
Specification data are reference values.
MONITOR ITEM
CONDITION
SPECIFICATION
PW/ST SIGNAL
I
Engine: After warming up, idle
the engine
Steering wheel in neutral position
(forward direction)
OFF
The steering wheel is fully turned
ON
ECM Terminals and Reference Value
NCEC0453
Specification data are reference values and are measured between each terminal and 48 (ECM ground).
TERMI-
NAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
46
PU/W
Power steering oil pressure
switch
[Engine is running]
I
Steering wheel is fully turned
Approximately 0V
[Engine is running]
I
Steering wheel is not turned
Approximately 5V
NEF124A
Power steering oil pressure switch
POWER STEERING OIL PRESSURE SWITCH
SR20DE
Component Description
EC-321
Wiring Diagram
NCEC0450
YEC254
POWER STEERING OIL PRESSURE SWITCH
SR20DE
Wiring Diagram
EC-322
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст