Nissan Primera P11. Instruction — part 411
I
Lock camshafts as shown in figure and tighten to specified
torque.
: 137 - 157 N
⋅
m (14.0 - 16.0 kg-m, 101 - 116 ft-lb)
Apply new engine oil to threads and seating surfaces of cam-
shaft sprocket bolts before installing them.
11. Install distributor.
I
Make sure that position of camshaft is as shown in figure.
I
Make sure that No. 1 piston is set at TDC and that distribu-
tor rotor is set at No. 1 cylinder spark position.
12. Install chain tensioner.
Make sure the camshaft sprockets are tightened completely.
Press cam stopper down and “press-in” sleeve until hook can
be engaged on pin. When tensioner is bolted in position the
hook will release automatically. Make sure arrow “A” points
toward engine front.
SEM049G
SEM050G
SEM033G
Rotor head position
(No. 1 cylinder at TDC)
SEM990C
SEM991C
CYLINDER HEAD
SR20DE
Installation (Cont’d)
EM-103
13. Install thermostat housing with water pipe.
14. Install intake manifold supports.
15. Remove old liquid gasket from mating surfaces of rocker cover
and cylinder head.
16. Apply a continuous bead of liquid gasket to rocker cover gas-
ket and cylinder head as shown in the illustrations.
I
Use Genuine RTV silicone sealant Part No. 999MP-A7007
or equivalent.
SEM066G
16 - 20
(1.6 - 2.1, 12 - 15)
6.3 - 8.3
(0.64 - 0.85,
56 - 73)
16 - 20
(1.6 - 2.1, 12 - 15)
16 - 20
(1.6 - 2.1,
12 - 15)
16 - 20
(1.6 - 2.1, 12 - 15)
6.3 - 8.3
(0.64 - 0.85,
56 - 73)
N·m (kg-m, in-lb)
N·m (kg-m, ft-lb)
SEM030G
Intake manifold
supports
BEM006
Engine
front
Unit: mm (in)
3 (0.12)
(0.39)
(0.39)
SEM051G
3 mm
(0.12 in) dia.
CYLINDER HEAD
SR20DE
Installation (Cont’d)
EM-104
17. Install rocker cover and oil separator.
I
Be sure to install washers between bolts and rocker cover.
I
Tightening procedure
STEP 1: Tighten bolts 1 - 10 - 11 - 13 - 8 in that order.
STEP 2: Tighten bolts 1 - 13 in that order.
: 8 - 10 N
⋅
m (0.8 - 1.0 kg-m, 69 - 87 in-lb)
18. Install the following parts:
I
Spark plugs and leads
I
Radiator
Refit hoses and refill with coolant.
Refer to MA-29, “Changing Engine Coolant”.
I
Front RH wheel
I
Engine undercovers
19. Connect the following:
I
Vacuum hoses
I
Fuel hoses
I
Wire harnesses and connectors
I
Air duct to intake manifold
I
Front exhaust tube
SEM052G
Engine
front
Tighten in numerical order.
Rocker cover
CYLINDER HEAD
SR20DE
Installation (Cont’d)
EM-105
Components
NEM340
Front engine slinger
Rear insulator
49 - 59
(5.0 - 6.0, 36 - 44)
Rear engine mounting
43 - 55
(4.4 - 5.6,
32 - 41)
43 - 55
(4.4 - 5.6,
32 - 41)
Rear engine slinger
20.6 - 26.5
(2.1 - 2.7, 15 - 20)
20.6 - 26.5
(2.1 - 2.7,
15 - 20)
43 - 55
(4.4 - 5.6,
32 - 41)
55 - 65
(5.6 - 6.6, 41 - 48)
49 - 59 (5.0 - 6.0, 36 - 44)
Front mounting
bracket
Insulator
Center member
77 - 98
(7.9 - 100, 57 - 72)
: N·m (kg-m, ft-lb)
.
43 - 55
(4.4 - 5.6, 32 - 41)
.
49 - 59
(5.0 - 6.0,
36 - 44)
43 - 55
(4.4 - 5.6, 32 - 41)
43 - 55
(4.9 - 5.6, 32 - 41)
49 - 59
(5.0 - 6.0,
36 - 44)
Front engine
mounting
Mounting
bracket
74 - 83 (7.5 - 8.5, 54 - 61)
43 - 55
(4.4 - 5.6, 32 - 41)
64 - 74
(6.5 - 7.5, 47 - 54)
64 - 74
(6.5 - 7.5, 47 - 54)
62 - 78
(6.3 - 8.0, 46 - 58)
64 - 74
(6.5 - 7.5, 47 - 54)
SEC. 112
.
43 - 55
(4.4 - 5.6, 32 - 41)
CVT models
ENGINE REMOVAL
SR20DE
Components
EM-106
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст