Nissan NV Passenger Van (2018 year). Manual — part 13

When the temperature control dial is
turned all the way to the cold setting, the air
flows only from the ceiling vents. When the
temperature control dial is turned all the
way to the hot setting, the air flows only
from the floor vents beneath the second
and third row of seats. When the tempera-
ture control dial is turned to a point be-
tween the coldest and hottest settings, the
air flows from both the floor and ceiling
vents.

The air conditioner system in your NISSAN
vehicle is charged with a refrigerant de-
signed with the environment in mind.

This refrigerant does not harm the
earth’s ozone layer.

Special charging equipment and lubricant
is required when servicing your NISSAN air
conditioner. Using improper refrigerants or
lubricants will cause severe damage to
your air conditioner system. For additional
information, refer to “Air conditioner sys-
tem refrigerant and oil recommendations”
in the “Technical and consumer informa-
tion” section of this manual.

It is recommended that you visit a NISSAN
dealer to service your “environmentally
friendly” air conditioner system.

WARNING

The air conditioner system contains
refrigerant under high pressure. To
avoid personal injury, any air condi-
tioner service should be done only by
an experienced technician with proper
equipment.

RADIO

With the ignition placed in the ACC or ON po-
sition, press the

(power) or ON•OFF but-

ton to turn the radio on. If you listen to the
radio with the engine not running, the ignition
should be placed in the ACC position.
Radio reception is affected by station sig-
nal strength, distance from radio transmit-
ter, buildings, bridges, mountains and other
external influences. Intermittent changes
in reception quality normally are caused by
these external influences.

Using a cellular phone in or near the vehicle
may influence radio reception quality.

Radio reception

Your NISSAN radio system is equipped with
state-of-the-art electronic circuits to en-
hance radio reception. These circuits are
designed to extend reception range, and to
enhance the quality of that reception.

However, there are some general charac-
teristics of both FM and AM radio signals
that can affect radio reception quality in a
moving vehicle, even when the finest
equipment is used. These characteristics
are completely normal in a given reception
area and do not indicate any malfunction
in your NISSAN radio system.

SERVICING AIR CONDITIONER

AUDIO SYSTEM

4-32

Monitor, climate, audio, phone and voice recognition systems

Reception

conditions

will

constantly

change because of vehicle movement.
Buildings, terrain, signal distance and inter-
ference from other vehicles can work
against ideal reception. Described below
are some of the factors that can affect your
radio reception.

Some cellular phones or other devices may
cause interference or a buzzing noise to
come from the audio system speakers.
Storing the device in a different location
may reduce or eliminate the noise.

FM RADIO RECEPTION

Range: FM range is normally limited to 25 –
30 mi (40 – 48 km), with monaural (single
channel) FM having slightly more range
than stereo FM. External influences may
sometimes interfere with FM station re-
ception even if the FM station is within 25
mi (40 km). The strength of the FM signal is
directly related to the distance between
the transmitter and receiver. FM signals fol-
low a line-of-sight path, exhibiting many of
the same characteristics as light. For ex-
ample, they will reflect off objects.

Fade and drift: As your vehicle moves away
from a station transmitter, the signals will
tend to fade and/or drift.

Static and flutter: During signal interfer-
ence from buildings, large hills or due to
antenna position (usually in conjunction
with increased distance from the station
transmitter), static or flutter can be heard.
This can be reduced by adjusting the treble
control to reduce treble response.

Multipath reception: Because of the reflec-
tive characteristics of FM signals, direct and
reflected signals reach the receiver at the
same time. The signals may cancel each
other, resulting in momentary flutter or loss
of sound.

AM RADIO RECEPTION

AM signals, because of their low frequency,
can bend around objects and skip along
the ground. In addition, the signals can be
bounced off the ionosphere and bent back
to earth. Because of these characteristics,
AM signals are also subject to interference
as they travel from transmitter to receiver.

Fading: Occurs while the vehicle is passing
through freeway underpasses or in areas
with many tall buildings. It can also occur
for several seconds during ionospheric tur-
bulence even in areas where no obstacles
exist.

Static: Caused by thunderstorms, electrical
power lines, electric signs and even traffic
lights.

SATELLITE RADIO RECEPTION
(if so equipped)

When the satellite radio is used for the first
time or the battery has been replaced, the
satellite radio may not work properly. This
is not a malfunction. Wait more than
10 minutes with satellite radio ON and the
vehicle outside of any metal or large build-
ing for satellite radio to receive all of the
necessary data.

No satellite radio reception is available un-
less there is an active SiriusXM® Satellite
Radio service subscription. Satellite radio is
not available in Alaska, Hawaii and Guam. If
satellite radio is not operational then
pressing the RADIO button will switch be-
tween FM and AM bands.

Satellite radio performance may be af-
fected if cargo carried on the roof blocks
the satellite radio signal.

If possible, do not put cargo over the satel-
lite antenna.

Monitor, climate, audio, phone and voice recognition systems

4-33

A build up of ice on the satellite radio an-
tenna can affect satellite radio perfor-
mance. Remove the ice to restore satellite
radio reception.

AUDIO OPERATION PRECAUTIONS

Compact disc (CD) player

CAUTION

∙ Do not force a compact disc into the

CD insert slot. This could damage the
CD and/or CD player.

∙ Trying to load a CD with the CD door

closed could damage the CD and/or
CD player.

∙ Only one CD can be loaded into the CD

player at a time.

Only use high quality 4.7 in (12 cm)

round discs that have the “COMPACT
disc DIGITAL AUDIO” logo on the disc
or packaging.

During cold weather or rainy days, the

player may malfunction due to the
humidity. If this occurs, remove the
CD and dehumidify or ventilate the
player completely.

The player may skip while driving on

rough roads.

The CD player sometimes cannot

function

when

the

compartment

temperature is extremely high or low.
Decrease/increase the temperature
before use.

LHA0099

4-34

Monitor, climate, audio, phone and voice recognition systems

Do not expose the CD to direct sun-

light.

CDs that are in poor condition or are

dirty, scratched or covered with fin-
gerprints may not work properly.

The following CDs may not work

properly:

Copy control compact discs (CCCD)

Recordable compact discs (CD-R)

Rewritable compact discs (CD-RW)

Do not use the following CDs as they

may cause the CD player to malfunc-
tion:

3.1 in (8 cm) discs with an adapter

CDs that are not round

CDs with a paper label

CDs that are warped, scratched, or

have abnormal edges

This audio system can only play pre-

recorded CDs. It has no capability to
record or burn CDs.

If the CD cannot be played, one of the

following messages will be displayed.

CHECK DISC

Confirm that the CD is inserted cor-

rectly (the label side is facing up,
etc.).

Confirm that the CD is not bent or

warped and it is free of scratches.

PRESS EJECT

This is an error due to excessive tem-
perature inside the player. Remove
the CD by pressing the EJECT button.
After a short time, reinsert the CD.
The CD can be played when the tem-
perature of the player returns to nor-
mal.

UNPLAYABLE

The file is unplayable in this audio
system (only MP3 or WMA CD).

Compact disc with MP3 or WMA

Terms

∙ MP3 — MP3 is short for Moving Pictures

Experts Group Audio Layer 3. MP3 is the
most well-known compressed digital
audio file format. This format allows for
near “CD quality” sound, but at a fraction
of the size of normal audio files. MP3
conversion of an audio track from CD-
ROM can reduce the file size by approxi-
mately a 10:1 ratio with virtually no per-
ceptible

loss

in

quality.

MP3

compression removes the redundant
and irrelevant parts of a sound signal
that the human ear doesn’t hear.

∙ WMA — Windows Media Audio (WMA)* is

a compressed audio format created by
Microsoft as an alternative to MP3. The
WMA codec offers greater file compres-
sion than the MP3 codec, enabling stor-
age of more digital audio tracks in the
same amount of space when com-
pared to MP3s at the same level of qual-
ity.

Monitor, climate, audio, phone and voice recognition systems

4-35

∙ Bit rate — Bit rate denotes the number

of bits per second used by a digital mu-
sic file. The size and quality of a com-
pressed digital audio file is determined
by the bit rate used when encoding the
file.

∙ Sampling frequency — Sampling fre-

quency is the rate at which the samples
of a signal are converted from analog to
digital (A/D conversion) per second.

∙ Multisession — Multisession is one of

the methods for writing data to media.
Writing data once to the media is called
a single session, and writing more than
once is called a multisession.

∙ ID3/WMA Tag — The ID3/WMA tag is the

part of the encoded MP3 or WMA file
that contains information about the
digital music file such as song title, art-
ist, encoding bit rate, track time dura-
tion, etc. ID3 tag information is displayed
on the Artist/song title line on the dis-
play.

* Windows® and Windows Media® are reg-
istered trademarks and trademarks in the
United States of America and other coun-
tries of Microsoft Corporation of the USA.

Playback order

Music playback order of a CD with MP3 or
WMA files is as illustrated.

∙ The names of folders not containing

MP3 or WMA files are not shown in the
display.

∙ If there is a file in the top level of the disc,

“Root Folder” is displayed.

∙ The playback order is the order in which

the files were written by the writing soft-
ware. Therefore, the files might not play
in the desired order.

Playback order chart

WHA1078

4-36

Monitor, climate, audio, phone and voice recognition systems

Specification chart

Supported media

CD, CD-R, CD-RW

Supported file systems

ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported.

Supported
versions*1

MP3

Version

MPEG1, MPEG2, MPEG2.5

Sampling
frequency

8 kHz - 48 kHz

Bit rate

8 kbps - 320 kbps, VBR

WMA

Version

WMA7, WMA8, WMA9

Sampling
frequency

32 kHz - 48 kHz

Bit rate

48 kbps - 192 kbps, VBR

Tag information

ID3 tag VER1.0, VER1.1, VER2.2, VER2.3 (MP3 only)

Folder levels

Folder levels: 8, Max folders: 255 (including root folder), Files: 512 (Max. 255 files for one folder)

Text character number limitation

128 characters

Displayable character codes*2

01: ASCII, 02: ISO-8859-1, 03: UNICODE (UTF-16 BOM Big Endian), 04: UNICODE (UTF-16 Non-BOM Big Endian),
05: UNICODE (UTF-8), 06: UNICODE (Non-UTF-16 BOM Little Endian)

*1 Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be played.

*2 Available codes depend on what kind of media, versions and information are going to be displayed.

Monitor, climate, audio, phone and voice recognition systems

4-37

Troubleshooting guide

Symptom

Cause and Countermeasure

Cannot play

Check if the disc was inserted correctly.

Check if the disc is scratched or dirty.

Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player.

If there is a temperature increase error, the CD player will play correctly after it returns to the normal temperature.

If there is a mixture of music CD files (CD-DA data) and MP3/WMA files on a CD, only the music CD files (CD-DA data) will be played.

Files with extensions other than “.MP3”,“.WMA”, “.mp3” or “.wma” cannot be played. In addition, the character codes and number of
characters for folder names and file names should be in compliance with the specifications.

Check if the finalization process, such as session close and disc close, is done for the disc.

Check if the disc is protected by copyright.

Poor sound quality

Check if the disc is scratched or dirty.

Bit rate may be too low.

It takes a relatively long
time before the music
starts playing.

If there are many folders or file levels on the MP3/WMA disc, or if it is a multisession disc, some time may be required before the music
starts playing.

Music cuts off or skips

The writing software and hardware combination might not match, or the writing speed, writing depth, writing width, etc., might not
match the specifications. Try using the slowest writing speed.

Skipping with high bit
rate files

Skipping may occur with large quantities of data, such as for high bit rate data.

Moves immediately to
the next song when
playing

When a non-MP3/WMA file has been given an extension of “.MP3”, “.WMA”, .“mp3”or “.wma”, or when play is prohibited by copyright
protection, there will be approximately 5 seconds of no sound and then the player will skip to the next song.

Songs do not play back
in the desired order

The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the
desired order.

4-38

Monitor, climate, audio, phone and voice recognition systems

USB (Universal Serial Bus)
Connection Port

WARNING

Do not connect, disconnect, or operate
the USB device while driving. Doing so
can be a distraction. If distracted you
could lose control of your vehicle and
cause an accident or serious injury.

CAUTION

∙ Do not force the USB device into the

USB port. Inserting the USB device
tilted or up-side-down into the port
may damage the port. Make sure that
the USB device is connected correctly
into the USB port.

∙ Do not grab the USB port cover (if so

equipped) when pulling the USB de-
vice out of the port. This could dam-
age the port and the cover.

∙ Do not leave the USB cable in a place

where it can be pulled unintentionally.
Pulling the cable may damage the
port.

The vehicle is not equipped with a USB de-
vice. USB devices should be purchased
separately as necessary.

This system cannot be used to format USB
memory devices. To format a USB device,
use a personal computer.

In some jurisdictions, the USB device for the
front seats plays only sound without im-
ages for regulatory reasons, even when the
vehicle is parked.

This

system

supports

various

USB

memory devices, USB hard drives and
iPod® players. Some USB devices may not
be supported by this system.

∙ Partitioned USB devices may not play

correctly.

∙ Some characters used in other lan-

guages (Chinese, Japanese, etc.) may
not appear properly in the display. Using
English language characters with a USB
device is recommended.

General notes for USB use

∙ For additional information, refer to your

device manufacturer’s owner informa-
tion regarding the proper use and care
of the device.

Notes for iPod® use

iPod® is a trademark of Apple Inc., regis-
tered in the U.S. and other countries.

∙ Improperly plugging in the iPod® may

cause a check mark to be displayed on
and off (flickering). Always make sure
that the iPod® is connected properly.

∙ An iPod® nano (1st Generation) may re-

main in fast forward or rewind mode if it
is connected during a seek operation. In
this case, please manually reset the
iPod®.

∙ An iPod® nano (2nd Generation) will

continue to fast-forward or rewind if it is
disconnected during a seek operation.

∙ An incorrect song title may appear

when the Play Mode is changed while
using an iPod® nano (2nd Generation).

∙ Audiobooks may not play in the same

order as they appear on an iPod®.

∙ Large video files cause slow responses

in an iPod®. The vehicle center display
may momentarily black out, but will
soon recover.

Monitor, climate, audio, phone and voice recognition systems

4-39

∙ If an iPod® automatically selects large

video files while in the shuffle mode, the
vehicle center display may momen-
tarily black out, but will soon recover.

iPod®* player

∙ Some characters used in other lan-

guages (Chinese, Japanese, etc.) are not
displayed properly on the vehicle center
screen. We recommend using English
language characters with an iPod®.

∙ Large video podcast files cause slow

responses in the iPod®. The vehicle cen-
ter display may momentarily black out,
but it will soon recover.

∙ If the iPod® automatically selects large

video podcast files while in the shuffle
mode, the vehicle center display may
momentarily black out, but it will soon
recover.

∙ Improperly plugging in the iPod® may

cause a checkmark to be displayed on
and off (flickering). Always make sure
that the iPod® is connected properly.

∙ The iPod® nano (2nd Generation) will

continue to fast forward or rewind if it is
disconnected during a seek operation.

∙ An incorrect song title may appear

when the Play Mode is changed while
using the iPod® nano (2nd Generation).

∙ Audiobooks may not play in the same

order as they appear on the iPod®.

∙ The iPod® nano (1st Generation) may

remain in fast forward or rewind mode if
it is connected during a seek operation.
In this case, please manually reset the
iPod®.

∙ If you are using an iPod® (3rd Generation

with Dock connector), do not use very
long names for the song title, album
name or artist name to prevent the
iPod® from resetting itself.

∙ Be careful not to do the following, or the

cable could be damaged and a loss of
function may occur:

∙ Bend the cable excessively (1.6 in

(40 mm) radius maximum).

∙ Twist the cable excessively (more

than 180 degrees).

∙ Pull or drop the cable.

∙ Do not force the iPod® cable connec-

tor into the device port.

∙ Close the center console lid on the

cable or connectors.

∙ Store objects with sharp edges in the

storage where the cable is stored.

∙ Spill liquids on the cable and connec-

tors.

∙ Do not connect the cable to the iPod® if

the cable and/or connectors are wet. It
may damage the iPod®.

∙ If the cable and connectors are ex-

posed to water, allow the cable and/or
connectors to dry completely before
connecting the cable to the iPod® (wait
24 hours for it to dry).

∙ If the connector is exposed to fluids

other than water, evaporative residue
may cause a short between the con-
nector pins. In this case, replace the
cable, otherwise damage to the iPod®
and a loss of function may occur.

∙ If the cable is damaged (insulation cut,

connectors

cracked,

contamination

such as liquids, dust, dirt, etc. in the con-
nectors), do not use the cable and con-
tact a NISSAN dealer to replace the
cable with a new one.

4-40

Monitor, climate, audio, phone and voice recognition systems

∙ When not in use for extended periods of

time, store the cable in a clean, dust free
environment at room temperature and
without direct sun exposure.

∙ Do not use the cable for any other pur-

poses other than its intended use in the
vehicle.

*iPod® is a trademark of Apple Inc., regis-
tered in the U.S. and other countries.

Bluetooth® streaming audio

∙ Some Bluetooth® audio devices may

not be recognized by the in-vehicle au-
dio system.

∙ It is necessary to set up the wireless

connection

between

a

compatible

Bluetooth® audio device and the in-
vehicle Bluetooth® module before using
the Bluetooth® audio.

∙ Operating procedure of the Bluetooth®

audio will vary depending on the de-
vices. Make sure how to operate your
audio device before using it with this
system.

∙ The Bluetooth® audio may be stopped

under the following conditions:

∙ Receiving a call on the Hands-Free

Phone System.

∙ Checking the connection to the

hands-free phone.

∙ Do not place the Bluetooth® audio de-

vice in an area surrounded by metal or
far away from the in-vehicle Bluetooth®
module to prevent tone quality degra-
dation and wireless connection disrup-
tion.

∙ While an audio device is connected

through the Bluetooth® wireless con-
nection, the battery power of the device
may discharge quicker than usual.

∙ This system supports the Bluetooth®

Audio Distribution Profile (A2DP, AVRCP).

BLUETOOTH® is a
trademark owned
by Bluetooth SIG,
Inc. and licensed
to Visteon and
Bosch.

Monitor, climate, audio, phone and voice recognition systems

4-41

FM/AM RADIO WITH COMPACT
DISC (CD) PLAYER (if so equipped)

For additional information, refer to “Audio
operation precautions” in this section.

1.

CD eject button

2. FM•AM button

3. CD insert slot

4. Display screen

5. SCAN button

6.

SEEK/TRACK buttons

7. iPod MENU button

8.

BACK button

9. ENTER/SETTING button and

TUNE/FOLDER control knob

10. Station select (1–6) buttons

11. RDM button

12. RPT button

13. VOL (volume) knob /

(power) button

14. DISP button

15. MEDIA button

16. CD button

Audio main operation

(power) button /

VOL (volume) control knob

Place the ignition switch in the ACC or ON
position and press the

(power) but-

ton while the system is off to call up the
mode (radio, CD, AUX, Bluetooth® audio,
USB or iPod®) that was playing immediately
before the system was turned off.

LHA3026

4-42

Monitor, climate, audio, phone and voice recognition systems

To turn the system off, press the
(power) button.
Turn the VOL (volume) control knob to
adjust the volume.

This vehicle may be equipped with Speed
Sensitive Volume. When this feature is ac-
tive, the audio volume changes as the driv-
ing speed changes.

ENTER/SETTING button

Press the ENTER/SETTING button to show
the Settings screen on the display. Turn the
TUNE/FOLDER knob to navigate the op-
tions and then press the ENTER/SETTING
button to make a selection.

Audio

Bass

Adjusts the bass to the desired level.

Treble

Adjusts the treble to the desired level.

Balance

Adjusts the balance to the desired level. Balance adjusts the sound level between the left and right speakers.

Fade

Adjusts the fade to the desired level. Fade adjusts the sound level between the front and rear speakers.

Brightness

Adjust the brightness to adjust the appearance of the display screen.

Contrast

Adjust the contrast to adjust the appearance of the display screen.

Clock Adjust

Allows the user to set time manually.

On-Screen Clock

Toggles ON or OFF the clock display on the upper right corner of the display screen.

RDS Display

Toggles ON or OFF the RDS information displayed on the screen while the radio is playing.

Speed Sensitive Vol. (volume)

Adjusts the speed sensitive volume function, which increases the volume of the audio system as the speed
of the vehicle increases. Set to “OFF” to disable the feature. The higher the setting, the more the volume
increases in relation to vehicle speed.

AUX Vol.

Choose a setting from 0 to +3 to control the boost of incoming auxiliary device volume. A setting of 0
provides no additional boost in volume. A setting of +3 provides the greatest boost in volume.

Language

Select the desired language for the system from the available options.

Auto Source Change

Select ON or OFF for the Auto Source Change. With Auto Source Change ON: when device is plugged into
USB port, radio will automatically switch to USB source. With Auto Source Change OFF: when device is
plugged into USB port, radio will stay on currently selected source.

Bass, treble, balance and fade can also be adjusted by pressing the ENTER/SETTING button and turning the TUNE/FOLDER control knob
to select the item to adjust. When the desired item is shown on the display, turn the tuning to adjust and then press the ENTER/SETTING
button until the display returns to the main audio screen. If the button is not pressed for approximately 10 seconds, the radio or CD display
will automatically reappear.

Monitor, climate, audio, phone and voice recognition systems

4-43

Clock Set

1. Press the ENTER/SETTING button.

2. Turn the TUNE/FOLDER knob to select

“Clock Adjust”.

3. Press the ENTER/SETTING button.

4. Turn the TUNE/FOLDER knob to adjust

hours.

5. Press the ENTER/SETTING button.

6. Rotate the TUNE/FOLDER knob to ad-

just minutes.

7. Press the ENTER/SETTING button.

8. Press the

BACK button to finish.

DISP button
The display screen can be turned off by
pressing the DISP button. You can listen to
music while the display is off. If you want to
turn the screen on, either press the DISP
button or press the FM·AM, CD or MEDIA
button.

iPod MENU button

This button can only be used for iPod® op-
erations. For additional information, refer to
“iPod® player operation without Navigation
System” in this section.

BACK button

Press the

BACK button to return to

the previous menu screen.

FM/AM radio operation

FM·AM button
Press the FM·AM button to change the
band as follows:

AM

→ FM1 → FM2 → AM

If another audio source is playing when the
FM·AM button is pressed, the audio source
playing will automatically be turned off and
the last radio station played will begin play-
ing.

TUNE/FOLDER knob (Tuning)

Turn the TUNE/FOLDER knob to the left or
right for manual tuning.

SEEK/TRACK tuning

Press the

TRACK button or

SEEK button to tune from low to high or
high to low frequencies and to stop at the
next broadcasting station.

SCAN tuning

Press the SCAN button to stop at each
broadcasting station for 5 seconds. SCAN
will appear on the screen while the radio is
scan tuning.

Pressing the button again during this
5 second period will stop SCAN tuning and
the radio will remain tuned to that station. If
the SCAN button is not pressed within
5 seconds, SCAN tuning moves to the next
station.

1 to 6 Station memory operations

Six stations can be set for the AM band.
Twelve stations can be set for the FM band
(six for FM1, six for FM2).

1. Choose the radio band AM, FM1 or FM2

using the FM·AM button.

2. Tune to the desired station using

manual, SEEK or SCAN tuning. Press
and hold any of the desired station
memory buttons (1 – 6) until the preset
number is updated on the display and
the sound is briefly muted.

3. The channel indicator will then come

on and the sound will resume. Pro-
gramming is now complete.

4-44

Monitor, climate, audio, phone and voice recognition systems

4. Other buttons can be set in the same

manner.

If the battery cable is disconnected, or if the
fuse opens, the radio memory will be can-
celed. In that case, reset the desired sta-
tions.

Compact disc (CD) player
operation

If the radio is already operating, it automati-
cally turns off and the compact disc begins
to play.

MEDIA button

With a CD loaded, press the MEDIA button
until the CD mode is displayed on the
screen.

CD/MP3 display mode

While listening to an MP3/WMA CD, certain
text may be displayed on the screen if the
CD has been encoded with text informa-
tion. Depending on how the MP3/WMA CD
is encoded, information such as Artist,
Song and Folder will be displayed.

The track number and the total number of
tracks in the current folder or on the cur-
rent disc are displayed on the screen as
well.

SEEK/TRACK (Reverse or

Fast Forward) button

Press

and

hold

the

SEEK/TRACK

button

or

for 1.5 seconds while

the compact disc is playing to reverse or
fast forward the track being played. The
compact disc plays at an increased speed
while reversing or fast forwarding. When
the button is released, the compact disc
returns to normal play speed.

SEEK/TRACK button

Press the

SEEK/TRACK button while a

CD or MP3/WMA CD is playing to return to
the beginning of the current track. Press
the

SEEK/TRACK button several times

to skip backward several tracks.

Press the

SEEK/TRACK button while a

CD or MP3/WMA CD is playing to advance
one track. Press the

SEEK/TRACK but-

ton several times to skip forward several
tracks. If the last track on a CD is skipped,
the first track on the disc is played. If the last
track in a folder of an MP3/WMA CD is
skipped, the first track of the next folder is
played.

TUNE/FOLDER knob (MP3/WMA CD only)

If a MP3/WMA CD with multiple folders is
playing, turn the TUNE/FOLDER knob to
change folders. Turn the knob to the left to
skip back a folder. Turn the knob to the right
to skip ahead a folder.

RPT (repeat) button

When the RPT button is pressed while a
compact disc is playing, the play pattern
can be changed as follows:

CD:

1 Track Repeat

←→ OFF

CD with MP3 or WMA:

1 Folder Repeat

→ 1 Track Repeat → OFF

1 Track Repeat: the current track will be
repeated.

1 Folder Repeat: the current folder will be
repeated.

OFF: No repeat play pattern is applied. The
indicator on the display will turn off.

The current play pattern of the CD is dis-
played on the screen unless no pattern is
applied.

Monitor, climate, audio, phone and voice recognition systems

4-45

RDM (random) button

When the RDM button is pressed while a
compact disc is playing, the play pattern
can be changed as follows:

CD:

1 Disc Random

←→ OFF

CD with MP3 or WMA:

1 Disc Random

→ 1 Folder Random → OFF

1 Disc Random: all tracks on the disc will be
played randomly.

1 Folder Random: all tracks in the current
folder will be played randomly.

OFF: No random play pattern is applied. The
indicator on the display will turn off.

The current play pattern of the CD is dis-
played on the screen unless no pattern is
applied.

EJECT button

When the

button is pressed with a

compact disc loaded, the compact disc will
eject and the last source will be played.

When the

button is pressed twice

with a compact disc loaded, the compact
disc will be ejected further for easier CD
removal. If the disc is not removed within
20 seconds, the disc will reload.

Additional features

For additional information, refer to “iPod®
player operation without Navigation Sys-
tem” in this section.

For additional information, refer to “USB
(Universal Serial Bus) connection port
(models without Navigation System)” in this
section.

For

additional

information,

refer

to

“Bluetooth® streaming audio without Navi-
gation System” in this section.

4-46

Monitor, climate, audio, phone and voice recognition systems

FM/AM/SAT RADIO WITH
COMPACT DISC (CD) PLAYER
(Type A) (if so equipped)

For additional information, refer to “Audio
operation precautions” in this section.

1.

CD eject button

2. RPT button

3. RDM button

4. Display screen

5. SCAN button

6.

SEEK/CAT buttons

7. iPod MENU button

8.

BACK button

9. ENTER/SETTING button and

TUNE/SCROLL control knob

10. Station select (1–6) buttons

11. VOL (volume) knob /

(power) button

12. DISP button

13. MEDIA button

14. XM button*

15. FM•AM button

*No satellite radio reception is available
when the XM button is pressed to access
satellite radio stations unless optional sat-
ellite receiver and antenna are installed
and an SiriusXM® Satellite Radio service
subscription is active. Satellite radio is not
available in Alaska, Hawaii or Guam.

LHA4427

Monitor, climate, audio, phone and voice recognition systems

4-47

Была ли эта страница вам полезна?
Да!Нет
1 посетитель считают эту страницу полезной.
Большое спасибо!
Ваше мнение очень важно для нас.

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.

Текст

Политика конфиденциальности