Nissan Frontier D22. Instruction — part 308
DTC P0447 EVAP CANISTER VENT CONTROL VALVE
EC-335
[KA24DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
3.
CHECK POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect EVAP canister vent control valve harness connector.
3.
Turn ignition switch ON.
4.
Check voltage between EVAP canister vent control valve termi-
nal 1 and ground with CONSULT-II or tester.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors E43, M65
●
Harness connectors M67, C1
●
Fuse block (J/B) connector E49
●
10A fuse
●
Harness for open or short between EVAP canister vent control valve and fuse
>> Repair harness or connectors.
5.
CHECK OUTPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between ECM terminal 108 and terminal 2.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
SEF143S
Voltage
: Battery voltage
SEF240W
Continuity should exist.
EC-336
[KA24DE]
DTC P0447 EVAP CANISTER VENT CONTROL VALVE
6.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors C1, M67
●
Harness connectors M81, F36
●
Harness for open or short between EVAP canister vent control valve and ECM
>> Repair open circuit or short to ground or short to power in harness or connectors.
7.
CHECK EVAP CANISTER VENT CONTROL VALVE-I
1.
Remove EVAP canister vent control valve from EVAP canister.
2.
Check portion B of EVAP canister vent control valve for being
rusted.
OK or NG
OK
>> GO TO 8.
NG
>> Replace EVAP canister vent control valve.
8.
CHECK EVAP CANISTER VENT CONTROL VALVE-II
With CONSULT-II
1.
Reconnect harness connectors disconnected.
2.
Turn ignition switch “ON”.
3.
Perform “VENT CONTROL/V” in “ACTIVE TEST” mode.
4.
Check air passage continuity and operation delay time.
Without CONSULT-II
Check air passage continuity and operation delay time under the fol-
lowing condition.
Operation takes less than 1 second.
OK or NG
OK
>> GO TO 10.
NG
>> GO TO 9.
BBIA0308E
Condition
Air passage continuity between
A and B
12V direct current supply between
terminals 1 and 2
No
OFF
Yes
SEF803Y
BBIA0309E
DTC P0447 EVAP CANISTER VENT CONTROL VALVE
EC-337
[KA24DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
9.
CHECK EVAP CANISTER VENT CONTROL VALVE-III
1.
Clean the air passage (Portion A to B ) of EVAP canister vent control valve using an air blower.
2.
Perform Test No. 8 again.
OK or NG
OK
>> GO TO 10.
NG
>> Replace EVAP canister vent control valve.
10.
CHECK INTERMITTENT INCIDENT
Perform
EC-120, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
>> INSPECTION END.
EC-338
[KA24DE]
DTC P0452 EVAP CONTROL SYSTEM PRESSURE SENSOR
DTC P0452 EVAP CONTROL SYSTEM PRESSURE SENSOR
PFP:25085
Component Description
UBS00D7S
The EVAP control system pressure sensor detects pressure in the
purge line. The sensor output voltage to the ECM increases as pres-
sure increases. The EVAP control system pressure sensor is not
used to control the engine system. It is used only for on board diag-
nosis.
CONSULT-II Reference Value in Data Monitor Mode
UBS00D7T
Specification data are reference values.
On Board Diagnosis Logic
UBS00D7U
SEF340V
PBIB1207E
MONITOR ITEM
CONDITION
SPECIFICATION
EVAP SYS PRES
●
Ignition switch: ON
1.8 - 4.8V
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0452
EVAP control system
pressure sensor low
input
An excessively low voltage from the sensor is
sent to ECM.
●
Harness or connectors
(The sensor circuit is open or shorted.)
●
EVAP control system pressure sensor
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст