Nissan Frontier D22. Instruction — part 385
TROUBLE DIAGNOSIS
EC-643
[VG33E]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DIAGNOSTIC WORKSHEET
Description
There are many operating conditions that lead to the malfunction of
engine components. A good grasp of such conditions can make trou-
ble-shooting faster and more accurate.
In general, each customer feels differently about a incident. It is
important to fully understand the symptoms or conditions for a cus-
tomer complaint.
Utilize a diagnostic worksheet like the one on the next page in order
to organize all the information for troubleshooting.
Some conditions may cause the MIL to come on steady or blink and
DTC to be detected. Examples:
●
Vehicle ran out of fuel, which caused the engine to misfire.
●
Fuel filler cap was left off or incorrectly screwed on, allowing fuel
to evaporate into the atmosphere.
SEF907L
EC-644
[VG33E]
TROUBLE DIAGNOSIS
Worksheet Sample
LEC031A
TROUBLE DIAGNOSIS
EC-645
[VG33E]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC Inspection Priority Chart
UBS00DF2
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
Priority
Detected items (DTC)
1
●
P0101, P0102, P0103 Mass air flow sensor
●
P0112, P0113, P0127 Intake air temperature sensor
●
P0117, P0118, P0125 Engine coolant temperature sensor
●
P0121, P0122, P0123 Throttle position sensor
●
P0181, P0182, P0183 Fuel tank temperature sensor
●
P0327, P0328 Knock sensor
●
P0335 P1336 CKP sensor (OBD)
●
P0340 CMP sensor
●
P0460 P0461 P1464 Fuel level sensor
●
P0500 VSS
●
P0600 A/T control
●
P0605 ECM
●
P1400 EGRC-solenoid valve
●
P1605 A/T diagnosis communication line
●
P1706 PNP switch
2
●
P0132-P0134, P1143, P1144/P0152-P0154, P1163, P1164 HO2S1
●
P0031, P0032/P0051, P0052 HO2S1 heater
●
P0138, P0139, P1146, P1147/P0158, P0159, P1166, P1167 HO2S2
●
P0037, P0038/P0057, P0058 HO2S2 heater
●
P0217 Engine coolant overtemperature enrichment protection
●
P0405, P0406 EGR temperature sensor
●
P0441 EVAP control system purge flow monitoring
●
P0444, P0445, P1444 EVAP canister purge volume control solenoid valve
●
P0447, P1446, P1448 EVAP canister vent control valve
●
P0452, P0453 EVAP control system pressure sensor
●
P0456, P1456 EVAP control system
●
P0510 CTP switch
●
P0705-P0755, P1705, P1760 A/T related sensors, solenoid valves and switches
●
P1490 P1491 Vacuum cut valve bypass valve
3
●
P0171, P0172, P0174, P0175 Fuel injection system function
●
P0306 - P0300 Misfire
●
P0400, P1402 EGR function
●
P0402 EGRC-BPT valve function
●
P0420, P0430 Three way catalyst function
●
P0442/P1442 EVAP control system
●
P0455 EVAP control system
●
P0505 ISC valve
●
P0731-P0734 P0744 A/T function
●
P1148, P1168 Closed loop control
EC-646
[VG33E]
TROUBLE DIAGNOSIS
Fail-safe Chart
UBS00DF3
When the DTC listed below is detected, the ECM enters the fail-sate mode and the MIL illuminates.
Basic Inspection
UBS00DF4
Precaution:
Perform Basic Inspection without electrical or mechanical loads applied;
●
Headlamp switch is OFF,
●
Air conditioner switch is OFF,
●
Rear window defogger switch is OFF,
●
Steering wheel is in the straight-ahead position, etc.
DTC No.
Detected items
Engine operating condition in fail-safe mode
P0102
P0103
Mass air flow sensor circuit
Engine speed will not rise more than 2,400 rpm due to the fuel cut.
P0117
P0118
Engine coolant temperature
sensor circuit
Engine coolant temperature will be determined by ECM based on the time after turning
ignition switch ON or START.
CONSULT-II displays the engine coolant temperature decided by ECM.
Condition
Engine coolant temperature decided (CONSULT-II
display)
Just as ignition switch is turned ON
or START
40
°C (104°F)
More than approx. 4 minutes after
ignition ON or START
80
°C (176°F)
Except as shown above
40 - 80
°C (104 - 176°F)
(Depends on the time)
P0122
P0123
Throttle position sensor cir-
cuit
Throttle position will be determined based on the injected fuel amount and the engine
speed.
Therefore, acceleration will be poor.
Condition
Driving condition
When engine is idling
Normal
When accelerating
Poor acceleration
Unable to
access ECM
ECM
ECM fail-safe activating condition
The computing function of the ECM was judged to be malfunctioning.
When the fail-safe system activates (i.e., if the ECM detects a malfunction condition in
the CPU of ECM), the MIL on the instrument panel lights to warn the driver.
However it is not possible to access ECM and DTC cannot be confirmed.
Engine control with fail-safe
When ECM fail-safe is operating, fuel injection, ignition timing, fuel pump operation, and
IACV-AAC valve operation are controlled under certain limitations.
ECM fail-safe operation
Engine speed
Engine speed will not rise more than 3,000 rpm
Fuel injection
Simultaneous multiport fuel injection system
Ignition timing
Ignition timing is fixed at the preset value
Fuel pump
Fuel pump relay is ON when engine is running
and OFF when engine stalls
IACV-AAC valve
Full open
Replace ECM, if ECM fail-safe condition is confirmed.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст