Nissan Frontier D22. Instruction — part 410
DTC P0121 TP SENSOR
EC-743
[VG33E]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0121 TP SENSOR
PFP:16119
Component Description
UBS00DGU
NOTE:
If DTC P0121 is displayed with DTC P0510, first perform the trouble diagnosis for DTC P0510. Refer to
The throttle position sensor responds to the accelerator pedal movement. This sensor is a kind of potentiome-
ter which transforms the throttle position into output voltage, and emits the voltage signal to the ECM. In addi-
tion, the sensor detects the opening and closing speed of the throttle valve and feeds the voltage signal to the
ECM.
Idle position of the throttle valve is determined by the ECM receiving the signal from the throttle position sen-
sor. This sensor controls engine operation such as fuel cut. On the other hand, the “Wide open and closed
throttle position switch”, which is built into the throttle position sensor unit, is not used for engine control.
CONSULT-II Reference Value in Data Monitor Mode
UBS00DGV
Specification data are reference values.
SEF349X
MONITOR ITEM
CONDITION
SPECIFICATION
THRTL POS SEN
●
Engine: After warming up, idle the
engine
Throttle valve: fully closed
0.15 - 0.85V
●
Engine: After warming up
●
Ignition switch: ON
(Engine stopped)
Throttle valve: fully opened
3.5 - 4.7V
ABSOL TH·P/S
●
Engine: After warming up
●
Ignition switch: ON
●
More than -40.0 kpa (-300 mmHg,
-11.81 inHg) of vacuum is applied
to the throttle opener with a hand
vacuum pump.
Throttle valve: fully closed
0.0%
●
Engine: After warming up
●
Ignition switch: ON
(Engine stopped)
Throttle valve: fully opened
Approx. 80%
EC-744
[VG33E]
DTC P0121 TP SENSOR
On Board Diagnosis Logic
UBS00DGW
DTC Confirmation Procedure
UBS00DGX
NOTE:
●
Perform PROCEDURE FOR MALFUNCTION A first. If the 1st trip DTC cannot be confirmed, per-
form PROCEDURE FOR MALFUNCTION B.
●
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait
at least 5 seconds before conducting the next test.
PROCEDURE FOR MALFUNCTION A
With CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Start engine and let it idle for at least 10 seconds.
If idle speed is over 1,000 rpm, maintain the following conditions
for at least 10 seconds to keep engine speed below 1,000 rpm.
4.
If 1st trip DTC is detected, go to
EC-747, "Diagnostic Procedure"
.
With GST
Follow the procedure “With CONSULT-II”.
PROCEDURE FOR MALFUNCTION B
CAUTION:
Always drive vehicle at a safe speed.
With CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Turn ignition switch OFF and wait at least 5 seconds.
3.
Turn ignition switch ON.
4.
Select “MANU TRIG” in “DATA MONITOR” mode with CONSULT-II.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0121
Throttle position sensor cir-
cuit range/performance prob-
lem
A)
A high voltage from the sensor is
sent to ECM under light load driving
condition.
●
Harness or connectors
(The TP sensor circuit is open or
shorted.)
●
TP sensor
●
Fuel injector
●
Camshaft position sensor
●
Mass air flow sensor
B)
A low voltage from the sensor is
sent to ECM under heavy load driv-
ing condition.
●
Harness or connectors
(The TP sensor circuit is open or
shorted.)
●
Intake air leaks
●
TP sensor
Selector lever
Suitable position except P or N (A/T), Neutral (M/T)
Brake pedal
Depressed
Vehicle speed
0 km/h (0 MPH)
SEF058Y
DTC P0121 TP SENSOR
EC-745
[VG33E]
C
D
E
F
G
H
I
J
K
L
M
A
EC
5.
Select “THRTL POS SEN” and “ABSOL TH·P/S” in “DATA MON-
ITOR” mode with CONSULT-II.
6.
Press RECORD on CONSULT-II screen at the same time accel-
erator pedal is depressed.
7.
Print out the recorded graph and check the following:
–
The voltage rise is linear in response to accelerator pedal
depression.
–
The voltage when accelerator pedal is fully depressed is approx-
imately 4V.
If NG, go to
EC-747, "Diagnostic Procedure"
If OK, go to following step.
8.
Select “AUTO TRIG” in “DATA MONITOR” mode with CON-
SULT-II.
9.
Maintain the following conditions for at least 10 consecutive sec-
onds.
10. If 1st trip DTC is detected, go to
EC-747, "Diagnostic Procedure"
.
With GST
Follow the procedure “With CONSULT-II”.
CMPS·RPM (REF)
More than 2,000 rpm
MAS AIR/FL SE
More than 3V
COOLAN TEMP/S
More than 70
°C (158°F)
IACV-AAC/V
Less than 80%
Selector lever
Suitable position
Driving location
Driving vehicle uphill (Increased engine load) will
help maintain the driving conditions required for
this test.
SEF177Y
SEF174Z
SEF805Z
EC-746
[VG33E]
DTC P0121 TP SENSOR
Wiring Diagram
UBS00DGY
BBWA0473E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст