Nissan Frontier D22. Instruction — part 767
IDX-8
ALPHABETICAL INDEX
Transmission case (M/T) . . . . . ..
,
Transmission serial number . . . . . .
,
Tread-FR&RR (Dimensions) . . . . . . . ...
Trim . . . . . . . . . . . . . . . . . .
Trouble diagnoses . . . . . . . . . . . .
Turbine revolution sensor . . . . . . . .
TURN - Wiring diagram . . . . . . . . . ..
Turn signal lamp . . . . . . . . . . . . .
Two trip detection logic . ...
,
Two-pole lift . . . . . . . . . . . . . .
U
Under body . . . . . . . . . . . . . .
V
Vacuum cut valve bypass valve
,
,
Vacuum hose (brake system) . . . . . . .
Vacuum hose drawing (Engine control) . .
Valve clearance . . . . . . . . ..
,
Valve guide . . . . . . . . . . .
,
Valve lifter . . . . . . . . . . . . . . .
Valve seat . . . . . . . . . . ...
,
Valve spring . . . . . . . . . .
,
VDC (vehicle dynamics control) . . . . . ..
VDC -Wiring diagram . . . . . ...
Vehicle identification number . . . . . . . ..
Vehicle recovery (freeing a stuck vehicle) . . ..
Viscosity number (SAE) . . . . . . . . .
VSS - Wiring diagram . ...
,
W
WARN - Wiring diagram . . . . . . . . . .
Warning chime . . . . . . . . . . . . .
Warning lamps . . . . . . . . . . . . .
Washer, front . . . . . . . . . . . . . .
Water pump . . . . . . . . . . ..
Water temperature gauge . . . . . . . . . .
Weatherstrip - See Exterior . . . . . . . .
Wheel alignment (front) . . . . . . . . ...
Wheel balance . . . . . . . . . . . . ..
Wheel bearing (front) . . . . . . . . . . .
Wheel bearing (rear) . . . . . . . . . . .
Wheel hub (front) . . . . . . . . . . . .
Wheel sensor (VDC) . . . . . . . . . .
Wheel sensors (ABS) . . . . .
Wheel size . . . . . . . . . . . . . . ..
Wheelbase (Dimensions) . . . . . . . . .
Width (Dimensions) . . . . . . . . . . .
WINDOW - Wiring diagram . . . . . . . ...
Window, back . . . . . . . . . .
Window, door . . . . . . . . . . . . .
Window, opera . . . . . . . . . . . . .
Window, rear . . . . . . . . . . . . .
WIPER - Wiring diagram . . . . . . . . .
Wiper, front . . . . . . . . . . . . . .
Wiring Diagram (Cell code) list . . . . . . .
Wiring diagrams . . . . . . . . . . . . ..
Withdrawal lever (clutch) . . . . . . . . .
Wrist pin - See Piston pin inspection ..
WT-T/WARN - Wiring diagram . . . . . . .
IP-1
INSTRUMENT PANEL
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION
A
B
IP
PRECAUTIONS . . . . . . . . . . . . . . .. 2
PREPARATION . . . . . . . . . . . . . . ... 3
Special Service Tools . . . . . . . . . . . ... 3
Commercial Service Tools . . . . . . . . . . 3
SQUEAK AND RATTLE TROUBLE DIAGNOSIS . .. 4
Squeak and Rattle Trouble Diagnoses . . . . . . 4
WORK FLOW . . . . . . . . . . . . . . 4
GENERIC SQUEAK AND RATTLE TROUBLE-
SHOOTING . . . . . . . . . . . . . . ... 6
DIAGNOSTIC WORKSHEET . . . . . . . . 8
IP-2
PRECAUTIONS
PRECAUTIONS
PFP:00001
Service Notice
EIS002DS
●
When removing or installing various parts, place a cloth or padding on the vehicle body to prevent
scratches.
●
Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to soil
or damage them.
●
Apply sealing compound where necessary when installing parts.
●
When applying sealing compound, be careful that the sealing compound does not protrude from parts.
●
When replacing any metal parts (for example body outer panel, members, etc.), be sure to take rust pre-
vention measures.
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
EIS002DT
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system may include seat belt switch inputs and dual stage front air bag modules. If
equipped with dual stage front air bag modules, the SRS system uses the seat belt switches to determine the
front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and
whether the front occupants are belted or unbelted. Information necessary to service the system safely is
included in the SRS and SB section of this Service Instruction.
The vehicle may be equipped with a passenger air bag deactivation switch. Because no rear seat exists where
a rear-facing child restraint can be placed, the switch is designed to turn off the passenger air bag so that a
rear-facing child restraint can be used in the front passenger seat. The switch is located in the center of the
instrument panel, near the ashtray. When the switch is turned to the ON position, the passenger air bag is
enabled and could inflate for certain types of collision. When the switch is turned to the OFF position, the pas-
senger air bag is disabled and will not inflate. A passenger air bag OFF indicator on the instrument panel lights
up when the passenger air bag is switched OFF. The driver air bag always remains enabled and is not affected
by the passenger air bag deactivation switch.
WARNING:
●
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harness connec-
tors.
●
The vehicle may be equipped with a passenger air bag deactivation switch which can be operated
by the customer. When the passenger air bag is switched OFF, the passenger air bag is disabled
and will not inflate. When the passenger air bag is switched ON, the passenger air bag is enabled
and could inflate for certain types of collision. After SRS maintenance or repair, make sure the
passenger air bag deactivation switch is in the same position (ON or OFF) as when the vehicle
arrived for service.
PREPARATION
IP-3
C
D
E
F
G
H
J
K
L
M
A
B
IP
PREPARATION
PFP:00002
Special Service Tools
EIS002DU
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
EIS002DV
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-39570)
Chassis Ear
Locating the noise
—
(J-43980)
NISSAN Squeak and Rattle Kit
Locating the noise
SBT839
SBT840
Tool name
Description
(J-39565)
Engine Ear
Locating the noise
SIIA0995E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст