Nissan Frontier D22. Instruction — part 866
PS-24
SERVICE DATA AND SPECIFICATIONS (SDS)
Tie-rod & relay-rod ball joint
Swinging force at cotter pin hole
15.7 - 147.1 N (1.6 - 15.0 kg, 3.5 - 33.1 lb)
Rotating torque
0.5 - 4.9 N·m (5 - 50 kg-cm, 4.3 - 43.4 in-lb)
Axial end play
0 mm (0 in)
Tie-rod standard length (L)
2WD and 4WD
297.6 mm (11.72 in)
Applied model
2WD, 4WD
AST251
RAX-1
REAR AXLE
D DRIVELINE/AXLE
CONTENTS
C
E
F
G
H
I
J
K
L
M
SECTION
A
B
RAX
PRECAUTIONS . . . . . . . . . . . . . . .. 2
Precautions . . . . . . . . . . . . . . . .. 2
PREPARATION . . . . . . . . . . . . . . ... 3
Special Service Tools . . . . . . . . . . . ... 3
Commercial Service Tools . . . . . . . . . . 4
NOISE, VIBRATION, AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 5
NVH Troubleshooting Chart . . . . . . . . . . 5
ON-VEHICLE SERVICE . . . . . . . . . . . . 6
Rear Axle Parts . . . . . . . . . . . . . . 6
Rear Wheel Bearing . . . . . . . . . . . . . 6
WHEEL HUB . . . . . . . . . . . . . . . .. 7
Components . . . . . . . . . . . . . . . . 7
Removal . . . . . . . . . . . . . . . . ... 8
Inspection After Removal . . . . . . . . . ... 10
Installation . . . . . . . . . . . . . . . .. 10
2WD MODELS . . . . . . . . . . . . . 10
4WD MODELS . . . . . . . . . . . . . 13
SERVICE DATA AND SPECIFICATIONS (SDS) . .. 17
Wheel Bearing (Rear) . . . . . . . . . . . . 17
2WD MODELS . . . . . . . . . . . . . 17
4WD MODELS . . . . . . . . . . . . . 17
RAX-2
PRECAUTIONS
PRECAUTIONS
PFP:00001
Precautions
EDS00143
●
When installing rubber parts, final tightening must be car-
ried out under unladen condition* with tires on ground.
*: Fuel, radiator coolant and engine oil full. Spare tire, jack,
hand tools and mats in designated positions.
●
Use flare nut wrench when removing and installing brake
tubes.
●
After installing removed suspension parts, check wheel
alignment and adjust if necessary.
●
Always torque brake lines when installing.
SBR686C
PREPARATION
RAX-3
C
E
F
G
H
I
J
K
L
M
A
B
RAX
PREPARATION
PFP:00002
Special Service Tools
EDS00144
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV40101000
(J25604-01)
Axle stand
Removing rear axle shaft
ST36230000
(J25840-A)
Slide hammer
Removing rear axle shaft
KV40106500
(J-45073)
Rear axle bearing remover
Removing wheel bearing, wheel bearing lock
nut and ABS sensor rotor
—
(J-46215)
Rear axle bearing installation kit
A: ABS sensor mount repair kit J-
46215-8
B: Plastic plugs and nuts kit J-46215-4
Installing rear axle bearing
—
(J-23907)
Seal and bushing puller
Removing rear axle seal
NT159
NT126
LPD022
LDIA0045E
LDIA0047E
LDIA0048E
LDIA0046E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст