Nissan Frontier D22. Instruction — part 796
MA-38
CHASSIS AND BODY MAINTENANCE
Changing A/T Fluid
ELS000XY
1.
Warm up A/T fluid.
2.
Stop engine.
3.
Drain A/T fluid from drain plug and refill with new A/T fluid.
Always refill same volume with drained fluid.
4.
Run engine at idle speed for five minutes.
5.
Check fluid level and condition. Refer to
. If fluid is still dirty, repeat steps 2
through 5.
Checking Transfer Fluid
ELS000XZ
Check for fluid leakage and fluid level.
ATF is used for the transfer in the factory.
CAUTION:
Never start engine while checking fluid level.
●
Apply sealant to filler plug threads.
●
Use Genuine Anaerobic Liquid Gasket or equivalent. Refer to
GI-42, "RECOMMENDED CHEMICAL PRODUCTS AND SEAL-
ANTS"
Changing Transfer Fluid
ELS000Y0
When changing transfer fluid completely, ATF may be used.
●
Apply sealant to drain plug threads.
●
Use Genuine Anaerobic Liquid Gasket or equivalent. Refer to
Fluid grade
Genuine NISSAN Matic
“D” ATF (Continental
U.S. and Alaska) or
Canada NISSAN Auto-
matic Transmission
Fluid.
: Refer to
OMMENDED FLUIDS AND
LUBRICANTS"
Fluid capacity (with torque converter)
KA24DE
: 7.9 (8 3/8 US qt, 7 Imp qt)
VG33E and VG33ER
2WD
: 8.3 (8 3/4 US qt, 7 1/4 Imp qt)
4WD
: 8.5 (9 US qt, 7 1/2 Imp qt)
Drain plug
: 29 - 39 N·m (3.0 - 4.0 kg-m, 22 - 29 ft-lb)
SMA515C
Filler plug
: 25 - 34 N·m (2.5 - 3.5 kg-m, 18 - 25 ft-lb)
SMA439B
Fluid grade
Genuine NISSAN Matic
“D” ATF (Continental U.S.
and Alaska) or Canada
NISSAN Automatic Trans-
mission Fluid or API GL-4,
Viscosity SAE 75W-85 or
75W-90
: Refer to
OMMENDED FLUIDS AND
LUBRICANTS"
Fluid capacity
: 2.2 (2 3/8 US qt, 2 Imp qt)
Drain plug
: 25 - 34 N·m (2.5 - 3.5 kg-m, 18 - 25 ft-lb)
SMA444B
CHASSIS AND BODY MAINTENANCE
MA-39
C
D
E
F
G
H
I
J
K
M
A
B
MA
Checking Propeller Shaft
ELS000Y1
Check propeller shaft for damage, looseness or grease leakage.
Greasing Propeller Shaft
ELS000Y2
Apply specified grease to nipples provided on propeller shaft.
Checking Differential Gear Oil
ELS000Y3
Check for oil leakage and oil level.
WMA042
WMA043
Grease grade
Refer to
SMA873C
Filler plug
Front — R200A
: 59 - 98 N·m (6 - 10 kg-m, 43 - 72 ft-lb)
Rear
H233B
: 59 - 98 N·m (6 - 10 kg-m, 43 - 72 ft-lb)
C200
: 39 - 59 N·m (4 - 6 kg-m, 29 - 43 ft-lb)
SMA440B
MA-40
CHASSIS AND BODY MAINTENANCE
Changing Differential Gear Oil
ELS000Y4
1.
Drain oil from drain plug and refill with new gear oil.
2.
Check oil level.
●
Apply sealant to plug threads.
●
Use Genuine Anaerobic Liquid Gasket or equivalent. Refer to
.
LIMITED-SLIP DIFFERENTIAL GEAR
●
Use only approved limited-slip differential gear oil. Refer to
MA-12, "RECOMMENDED FLUIDS AND
●
Limited-slip differential identification.
1.
Lift both rear wheels off the ground.
SMA632C
SMA631C
Oil grade and viscosity
: Refer to
MA-12, "RECOMMENDED FLUIDS AND LUBRICANTS"
Oil capacity
Front — R200A
: 1.75 (3 3/4 US pt, 3 1/8 Imp pt)
Rear
H233B
: 2.8 (5 7/8 US pt, 4 7/8 Imp pt)
C200
: 1.3 (2 3/4 US pt, 2 1/4 Imp pt)
Filler plug
Front — R200A
: 59 - 98 N·m (6 - 10 kg-m, 43 - 72 ft-lb)
Rear
H233B
: 59 - 98 N·m (6 - 10 kg-m, 43 - 72 ft-lb)
C200
: 39 - 59 N·m (4 - 6 kg-m, 29 - 43 ft-lb)
Drain plug
Front –– R200A
: 59 - 98 N·m (6 - 10 kg-m, 43 - 72 ft-lb)
Rear
H233B
: 59 - 98 N·m (6 - 10 kg-m, 43 - 72 ft-lb)
C200
: 59 - 98 N·m (6 - 10 kg-m, 43 - 72 ft-lb)
CHASSIS AND BODY MAINTENANCE
MA-41
C
D
E
F
G
H
I
J
K
M
A
B
MA
2.
Turn one rear wheel by hand.
3.
If both rear wheels turn in the same direction simultaneously, vehicle is equipped with limited-slip differen-
tial.
Balancing Wheels
ELS000Y5
Adjust wheel balance using the road wheel center.
Tire Rotation
ELS000Y6
●
After rotating the tires, adjust the tire pressure.
●
Retighten the wheel nuts when the vehicle has been driven for
1,000 km (600 miles) (also in cases of a flat tire, etc.).
Checking Brake Fluid Level and Leaks
ELS000Y7
●
Check fluid level in reservoir tank. It should be between MAX
and MIN lines on reservoir tank.
●
If fluid level is extremely low, check brake system.
●
If the brake warning lamp comes on, check brake fluid level
switch and parking brake switch.
Checking Brake Lines and Cables
ELS000Y8
CAUTION:
If leakage occurs around joints, retighten or, if necessary,
replace damaged parts.
1.
Check brake lines (tubes and hoses) for cracks, deterioration
and other damage. Replace any damaged parts.
2.
Check for oil leakage by fully depressing brake pedal while
engine is running.
Wheel balance (maximum allowable unbalance)
: Refer to
.
Wheel nuts
: 98 - 117 N·m (10 - 12 kg-m, 73 - 86 ft-lb)
AMA159
SBR451D
SBR389C
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст