Nissan Titan (2019 year). Manual — part 12

GROCERY HOOKS (if so equipped)

The grocery hooks allow for standard size
plastic grocery bags to hang side by side.

To access the grocery hooks, fold up the
rear bench seat. For additional information,
refer to “Folding the rear bench seat up” in
the “Safety — Seats, seat belts and supple-
mental restraint system” section of this
manual.

CAUTION

Do not apply a total load of more than
18 lbs. (8 kg) to a single grocery hook.

BED LINER STORAGE BINS (if so
equipped)

To open the bed liner storage bins on the
top of the wheel wells, unlock the bin and
lift the lid toward the inside of the truck bed.

To close, replace the lid and lock the bin.

To open the bed liner storage bins on the
tail gate end of the bed liner, lift the tab
away from the truck bed, pull the lid up and
away from the truck.

LIC3389

LIC3449

LIC3450

Instruments and controls

2-81

CARGO HOOKS (if so equipped)

When securing items using cargo hooks,
located on the rear door pillars, do not ap-
ply a load more than 110 lbs. (490 N) to a
single hook.

The cargo hooks that are located on the
floor should have loads less than 110 lbs.
(490 N) to a single hook.

The cargo hooks can be used to secure
cargo with ropes or other types of straps.

WARNING

∙ Properly secure all cargo with ropes or

straps to help prevent it from sliding
or shifting. Do not place cargo higher
than the seatbacks. In a sudden stop
or collision, unsecured cargo could
cause personal injury.

∙ Use suitable ropes and hooks to se-

cure cargo.

∙ Never allow anyone to ride in the

cargo area. It is extremely dangerous
to ride in a cargo area inside of a ve-
hicle. In a collision, people riding in
these areas are more likely to be seri-
ously injured or killed.

∙ Do not allow people to ride in any area

of your vehicle that is not equipped
with seats and seat belts.

∙ The child restraint top tether strap

may be damaged by contact with
items in the cargo area. Secure any
items in the cargo area. Your child
could be seriously injured or killed in a
collision if the top tether strap is
damaged.

∙ Be sure everyone in your vehicle is in a

seat and using a seat belt properly.

C-CHANNEL CARGO HOOKS (if so
equipped)

The C-Channel cargo hooks, located on the
back panel, can be used to secure cargo
with ropes or other types of straps.

When securing items using C-Channel
cargo hooks, located on the back panel, do
not apply a load more than 110 lbs. (490 N)
to a single hook.

LIC3709

LIC3710

2-82

Instruments and controls

WARNING

∙ Properly secure all cargo with ropes or

straps to help prevent it from sliding
or shifting. Do not place cargo higher
than the seatbacks. In a sudden stop
or collision, unsecured cargo could
cause personal injury.

∙ Use suitable ropes and hooks to se-

cure cargo.

∙ Never allow anyone to ride in the

cargo area. It is extremely dangerous
to ride in a cargo area inside of a ve-
hicle. In a collision, people riding in
these areas are more likely to be seri-
ously injured or killed.

∙ Do not allow people to ride in any area

of your vehicle that is not equipped
with seats and seat belts.

∙ The child restraint top tether strap

may be damaged by contact with
items in the cargo area. Secure any
items in the cargo area. Your child
could be seriously injured or killed in a
collision if the top tether strap is
damaged.

∙ Be sure everyone in your vehicle is in a

seat and using a seat belt properly.

POWER WINDOWS

WARNING

∙ Make sure that all passengers have

their hands, etc., inside the vehicle
while it is in motion and before closing
the windows. Use the window lock
switch to prevent unexpected use of
the power windows.

∙ To help avoid risk of injury or death

through unintended operation of the
vehicle and/or its systems, including
entrapment in windows or inadver-
tent door lock activation, do not leave
children, people who require the as-
sistance of others or pets unattended
in your vehicle. Additionally, the tem-
perature inside a closed vehicle on a
warm day can quickly become high
enough to cause a significant risk of
injury or death to people and pets.

The power windows operate when the ig-
nition switch is placed in the ON position or
for a period of time after the ignition switch
is placed in the OFF position. If the driver’s
or passenger’s door is opened during this
period of time, the power to the windows is
canceled.

1.

Window lock button

2.

Power door lock switch

3.

Front passenger side automatic
window switch

4.

Right rear passenger window
switch (if so equipped)

5.

Left rear passenger window switch
(if so equipped)

6.

Driver side automatic window
switch

WIC1124

WINDOWS

Instruments and controls

2-83

Driver’s side power window
switch

The driver’s side control panel is equipped
with switches to open or close the front
and rear (if so equipped) passenger win-
dows.

To open a window, push the switch and
hold it down. To close a window, pull the
switch and hold it up. To stop the opening
or closing function at any time, simply re-
lease the switch.

Front passenger’s power window
switch

The passenger’s window switch operates
only the corresponding passenger’s win-
dow. To open the window, push the switch
and hold it down

䊊

1

. To close the window,

pull the switch up

䊊

2

.

Rear power window switch (if so
equipped)

The rear power window switches open or
close only the corresponding windows. To
open the window, push the switch and hold
it down

䊊

1

. To close the window, pull the

switch up

䊊

2

.

Locking passengers’ windows

When the window lock switch is depressed,
only the driver’s side window can be
opened or closed. Push it again to cancel
the window lock function.

WIC1125

WIC0261

2-84

Instruments and controls

Automatic operation

To fully open a window equipped with au-
tomatic

operation,

push

the

window

switch down to the second detent and re-
lease it; it need not be held. The window
automatically opens all the way. To stop
the window, lift the switch up while the win-
dow is opening.

To fully close a window equipped with au-
tomatic operation, pull the switch up to the
second detent and release it; it need not be
held. To stop the window, push the switch
down while the window is closing.

Auto-reverse function

The auto-reverse function can be acti-
vated when a window is closed by auto-
matic operation.

Depending on the environment or driv-
ing conditions, the auto-reverse func-
tion may be activated if an impact or
load similar to something being caught
in the window occurs.

WARNING

There are some small distances imme-
diately before the closed position which
cannot be detected. Make sure that all
passengers have their hands, etc., in-
side the vehicle before closing the
window.

If the vehicle’s battery is disconnected, re-
placed, or jump started, the power window
auto-reverse function may not operate
properly. Have the power window auto-
reverse system re-initialized. It is recom-
mended that you visit a NISSAN dealer for
this service.

If the control unit detects something
caught in a window equipped with auto-
matic operation as it is closing, the window
will be immediately lowered.

REAR POWER WINDOW SWITCH (if
so equipped)

WARNING

∙ You must ensure all occupants and

objects are free of the rear window
area prior to and during operation.
Failure to do so may result in injury
and/or damage to the rear window
system.

∙ The rear window is not designed to

carry long items through it.

LIC0410

LIC3448

Instruments and controls

2-85

∙ Do not place objects through the

opened rear window. Do not use the
rear window as a cargo area pass-
through. This may result in damage to
the rear window system, or personal
injury.

WARNING

∙ To help avoid risk of injury or death

through unintended operation of the
vehicle and or its systems, including
entrapment in windows or inadver-
tent door lock activation, do not leave
children, people who require the as-
sistance of others or pets unattended
in your vehicle. Additionally, the tem-
perature inside a closed vehicle on a
warm day can quickly become high
enough to cause a significant risk of
injury or death to people and pets.

To open the rear power window, push in
and hold the switch.

To close the rear power window, pull out
and hold the switch.

To stop the opening or closing function at
any time, simply release the switch.

NOTE:

If the rear power window is opened while
the defroster switch is on, the rear win-
dow defroster (if so equipped) will auto-
matically shut off. The heated outside
mirrors (if so equipped) will remain on.
The rear window defroster will auto-
matically turn on when the rear power
window is fully closed if the switch is on.

REAR SLIDING WINDOW (if so
equipped)

WARNING

∙ You must ensure all occupants and

objects are free of the rear window
area prior to and during operation.
Failure to do so may result in injury
and/or damage to the rear window
system.

∙ The rear window is not designed to

carry long items through it.

LIC3488

2-86

Instruments and controls

∙ Do not place objects through the

opened rear window. Do not use the
rear window as a cargo area pass-
through. This may result in damage to
the rear window system, or personal
injury.

Squeeze the handles of the lever

䊊

1

, then

slide the window open

䊊

2

.

The interior light has a three-position
switch and operates regardless of ignition
switch position.

When the switch is in the ON position

䊊

1

,

the interior lights illuminate, regardless of
door position. The lights will go off after a
period of time unless the ignition switch is
placed in the ON position.

When the switch is in the DOOR or normal
operation position

䊊

2

, the interior lights,

puddle lights (if so equipped), and cargo
light will stay on for a period of time when:

∙ The doors are unlocked by the key fob, a

key or the power door lock switch while
all doors are closed and the ignition
switch is in the OFF position.

∙ The driver’s door is opened and then

closed while the key is removed from
the ignition switch.

∙ The key (if so equipped) is removed

from the ignition switch while all doors
are closed.

The lights will turn off while the timer is
activated when:

∙ The driver’s door is locked by the key

fob, a key, or the power door lock switch.

∙ The ignition switch is turned ON.

When the switch is in the OFF position

䊊

3

,

the interior lights do not illuminate, regard-
less of door position. The puddle lights (if so
equipped) and cargo light come on when
any front or rear passenger door is opened.

The lights will turn off automatically after a
period of time while doors are open to pre-
vent the battery from becoming dis-
charged.

LIC0792

INTERIOR LIGHTS

Instruments and controls

2-87

CAUTION

Do not use for extended periods of time
with the engine stopped. This could re-
sult in a discharged battery.

CONSOLE LIGHT (if so equipped)

The console light will turn on whenever the
parking lights or headlights are illuminated.

The console light brightness can be ad-
justed with the illumination brightness
control.

MAP LIGHTS (if so equipped)

To turn the map lights on, push the
switches. To turn them off, push the
switches again.

CAUTION

Do not use for extended periods of time
with the engine stopped. This could re-
sult in a discharged battery.

LIC3405

LIC0790

2-88

Instruments and controls

PERSONAL LIGHTS (if so equipped)

To turn the rear personal lights on, push the
switch. To turn them off, push the switch
again.

The HomeLink® Universal Transceiver pro-
vides a convenient way to consolidate the
functions of up to three individual hand-
held transmitters into one built-in device.

HomeLink® Universal Transceiver:

∙ Will operate most radio frequency de-

vices such as garage doors, gates,
home and office lighting, entry door
locks and security systems.

∙ Is powered by your vehicle’s battery. No

separate batteries are required. If the
vehicle’s battery is discharged or is dis-
connected, HomeLink® will retain all
programming.

When the HomeLink® Universal Trans-
ceiver is programmed, retain the original
transmitter for future programming pro-
cedures (Example: new vehicle pur-
chases). Upon sale of the vehicle, the
programmed

HomeLink®

Universal

Transceiver buttons should be erased for
security purposes. For additional infor-
mation,

refer

to

“Programming

HomeLink®” in this section.

WARNING

∙ Do not use the HomeLink® Universal

Transceiver with any garage door
opener that lacks safety stop and re-
verse features as required by federal
safety standards. (These standards
became effective for opener models
manufactured after April 1, 1982). A
garage door opener which cannot de-
tect an object in the path of a closing
garage door and then automatically
stop and reverse, does not meet cur-
rent federal safety standards. Using a
garage door opener without these
features increases the risk of serious
injury or death.

∙ During the programming procedure

your garage door or security gate will
open and close (if the transmitter is
within range). Make sure that people
or objects are clear of the garage door,
gate, etc. that you are programming.

Rear personal lights

LIC0790

HOMELINK® UNIVERSAL
TRANSCEIVER (if so equipped)

Instruments and controls

2-89

∙ Your

vehicle’s

engine

should

be

turned off while programming the
HomeLink® Universal Transceiver. Do
not breathe exhaust gases; they con-
tain colorless and odorless carbon
monoxide. Carbon monoxide is dan-
gerous. It can cause unconsciousness
or death.

PROGRAMMING HOMELINK®

If you have any questions or are having
difficulty programming your HomeLink®
buttons, refer to the HomeLink® web site at:
www.homelink.com or call 1-800-355-3515.

NOTE:

Place the ignition switch in the ACC posi-
tion when programming HomeLink®. It is
also recommended that a new battery
be placed in the hand-held transmitter
of the device being programmed to
HomeLink® for quicker programming
and accurate transmission of the radio
frequency.

1. Position the end of your hand-held

transmitter 1–3 in (2–8 cm) away from
the HomeLink® surface, keeping the
HomeLink® indicator light

䊊

1

in view.

2. Using

both

hands,

simultaneously

press and hold the desired HomeLink®
button and hand-held transmitter but-
ton.

DO

NOT

release

until

the

HomeLink® indicator light

䊊

1

flashes

slowly and then rapidly. When the indi-
cator light flashes rapidly, both buttons
may be released. (The rapid flashing
indicates successful programming.)

LIC2365

LIC2366

2-90

Instruments and controls

NOTE:

Some devices may require you to replace
Step 2 with the cycling procedure noted
in “Programming HomeLink® for Cana-
dian customers and gate openers” in this
section.

3. Press

and

hold

the

programmed

HomeLink® button and observe the in-
dicator light.

∙ If

the

indicator

light

䊊

1

is

solid/continuous, programming is
complete and your device should
activate when the HomeLink® button
is pressed and released.

∙ If the indicator light

䊊

1

blinks rapidly

for 2 seconds and then turns to a
solid/continuous

light,

continue

with Steps 4-6 for a rolling code de-
vice. A second person may make the
following steps easier. Use a ladder or
other device. Do not stand on your
vehicle to perform the next steps.

4. At the receiver located on the garage

door opener motor in the garage, lo-
cate the “learn” or “smart” button (the
name and color of the button may vary
by manufacturer but it is usually lo-
cated near where the hanging an-

tenna wire is attached to the unit). If
there is difficulty locating the button,
reference the garage door opener’s
manual.

5. Press and release the “learn” or “smart”

button.

6. Return to the vehicle and firmly press

and hold the trained HomeLink® but-
ton for 2 seconds and release. Repeat
the “press/hold/release” sequence up
to three times to complete the training
process. HomeLink® should now acti-
vate your rolling code equipped device.

7. If you have any questions or are having

difficulty

programming

your

HomeLink®

buttons,

refer

to

the

HomeLink®

web

site

at:

www.homelink.com or call 1-800-355-
3515.

PROGRAMMING HOMELINK® FOR
CANADIAN CUSTOMERS AND GATE
OPENERS

Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission –
which may not be long enough for
HomeLink® to pick up the signal during
training. Similar to this Canadian law, some

U.S. gate operators are designed to “tim-
eout” in the same manner.

If you live in Canada or you are having diffi-
culties training a gate operator or garage
door opener by using the “Training” proce-
dures, replace “Programming HomeLink®”
step 2 with the following:

NOTE:

When

programming

a

garage

door

opener, etc., unplug the device during
the “cycling” process to prevent possible
damage to the garage door opener com-
ponents.

1. For additional information, refer to “Pro-

gramming HomeLink®” step 1 in this
section.

2. Using

both

hands,

simultaneously

press and hold the desired HomeLink®
button and the hand-held transmitter
button. During training, your hand-held
transmitter may automatically stop
transmitting. Continue to press and
hold the desired HomeLink® button
while you press and re-press (“cycle”)
your

hand-held

transmitter

every

2 seconds until the frequency signal
has been learned. The HomeLink® indi-
cator light will flash slowly and then

Instruments and controls

2-91

rapidly after several seconds upon
successful training. DO NOT release un-
til the HomeLink® indicator light flashes
slowly and then rapidly. When the indi-
cator light flashes rapidly, both buttons
may be released. The rapid flashing in-
dicates successful training.
Proceed

with

“Programming

HomeLink®” step 3 to complete.
If the device was unplugged during the
programming procedure, remember
to plug it back in when programming is
completed.

OPERATING THE HOMELINK®
UNIVERSAL TRANSCEIVER

The HomeLink® Universal Transceiver, after
it is programmed, can be used to activate
the programmed device. To operate, sim-
ply press and release the appropriate pro-
grammed HomeLink® Universal Trans-
ceiver button. The amber indicator light will
illuminate while the signal is being trans-
mitted.

For convenience, the hand-held transmit-
ter of the device may also be used at any
time.

PROGRAMMING TROUBLE-
DIAGNOSIS

If the HomeLink® does not quickly learn the
hand-held transmitter information:

∙ Replace the hand-held transmitter bat-

teries with new batteries.

∙ Position the hand-held transmitter with

its battery area facing away from the
HomeLink® surface.

∙ Press and hold both the HomeLink®

and hand-held transmitter buttons
without interruption.

∙ Position the hand-held transmitter 1 -

3 inches (26 - 76 mm) away from the
HomeLink® surface. Hold the transmit-
ter in that position for up to 15 seconds.
If HomeLink® is not programmed within
that time, try holding the transmitter in
another position – keeping the indicator
light in view at all times.

If you have any questions or are having
difficulty programming your HomeLink®
buttons, refer to the HomeLink® web site at:
www.homelink.com or call 1-800-355-3515.

CLEARING THE PROGRAMMED
INFORMATION

The following procedure clears the pro-
grammed information from both buttons.
Individual buttons cannot be cleared. How-
ever, individual buttons can be repro-
grammed. For additional information, refer
to “Reprogramming a single HomeLink®
button” in this section.

To clear all programming:

1. Press

and

hold

the

two

outer

HomeLink® buttons until the indicator
light begins to flash in approximately
10 seconds. Do not hold for longer than
20 seconds.

2. Release both buttons.

HomeLink® is now in the programming
mode and can be programmed at any
time

beginning

with

“Programming

HomeLink®” - Step 1.

REPROGRAMMING A SINGLE
HOMELINK® BUTTON

To reprogram a HomeLink® Universal
Transceiver button, complete the following:

1. Press and hold the desired HomeLink®

button. DO NOT release the button.

2-92

Instruments and controls

2. The indicator light will begin to flash

after 20 seconds. Without releasing the
HomeLink® button, proceed with “Pro-
gramming HomeLink®” - Step 1.

For

questions

or

comments,

contact

HomeLink®

at:

www.homelink.com

or

1–800–355–3515 (except Mexico).

The HomeLink® Universal Transceiver but-
ton has now been reprogrammed. The
new device can be activated by pressing
the HomeLink® button that was just pro-
grammed. This procedure will not affect
any other programmed HomeLink® but-
tons.

IF YOUR VEHICLE IS STOLEN

If your vehicle is stolen, you should change
the codes of any non-rolling code device
that

has

been

programmed

into

HomeLink®. Consult the Owner’s Manual of
each device or call the manufacturer or
dealer of those devices for additional infor-
mation.

When your vehicle is recovered, you will
need to reprogram the HomeLink® Uni-
versal Transceiver with your new trans-
mitter information.

FCC Notice:

For USA:

This device complies with Part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause interference, and (2) this
device must accept any interference re-
ceived, including interference that may
cause undesired operation.

NOTE:

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.

For Canada:

This

device

complies

with

Industry

Canada licence-exempt RSS standard(s).
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must ac-
cept any interference, including interfer-
ence that may cause undesired opera-
tion of the device.

Instruments and controls

2-93

3 Pre-driving checks and adjustments

Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

NISSAN Intelligent Key® . . . . . . . . . . . . . . . . . . . . . . . 3-2
NISSAN Vehicle Immobilizer System
keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Locking with key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Locking with inside lock knob. . . . . . . . . . . . . . . . . 3-7
Locking with power door lock switch . . . . . . . . . 3-7
Rear doors (King Cab® models) . . . . . . . . . . . . . . . 3-8
Automatic door locks (if so equipped) . . . . . . . . 3-9
Child safety rear door lock
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

NISSAN Intelligent Key® . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Operating range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Door locks/unlocks precaution . . . . . . . . . . . . . . 3-12
NISSAN Intelligent Key® Operation . . . . . . . . . . . 3-13
How to use the remote keyless entry
function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Warning signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . 3-22

Remote Engine Start (if so equipped) . . . . . . . . . . . 3-24

Remote Engine Start operating range . . . . . . . 3-24
Remote starting the vehicle . . . . . . . . . . . . . . . . . 3-25

Extending engine run time . . . . . . . . . . . . . . . . . . 3-25
Canceling a Remote Engine Start . . . . . . . . . . . . 3-25
Conditions the Remote Engine Start will
not work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26

Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27
Fuel-filler door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27

Diesel fuel engines . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28
Gasoline fuel engines . . . . . . . . . . . . . . . . . . . . . . . . 3-28

Steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30

Manual operation (if so equipped) . . . . . . . . . . . 3-31
Automatic operation (if so equipped) . . . . . . . . 3-31

Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32

Vanity mirrors (if so equipped) . . . . . . . . . . . . . . . 3-33
Card holder (driver’s side only) . . . . . . . . . . . . . . . 3-33

Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33

Manual anti-glare rearview mirror
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33
Automatic anti-glare rearview mirror
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-34
Outside mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-35

Truck box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39

Tailgate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39
Tie down hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43

Automatic drive positioner (if so equipped) . . . . . 3-43

Memory storage function . . . . . . . . . . . . . . . . . . . 3-44

Entry/exit function . . . . . . . . . . . . . . . . . . . . . . . . . . 3-45
System operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-45

1.

Master key

2.

Transponder chip

3.

Key number plate

A key number plate is supplied with your
keys. Record the key number and keep it in
a safe place (such as your wallet), not in the
vehicle. If you lose your keys, it is recom-
mended that you visit a NISSAN dealer for
duplicates by using the key number.
NISSAN does not record key numbers so it
is very important to keep track of your key
number plate.

A key number is only necessary when you
have lost all your keys. If you still have a key,
it can be duplicated without knowing the
key number.

1.

Intelligent Key (two sets)

2.

Mechanical key

3.

Key number plate (one plate)

NISSAN INTELLIGENT KEY®

Your vehicle can only be driven with the
Intelligent Keys which are registered to
your vehicle’s Intelligent Key system com-
ponents and NISSAN Vehicle Immobilizer
System components.

LPD2130

Type A (if so equipped)

LPD2842

KEYS

3-2

Pre-driving checks and adjustments