Nissan Rogue. Instruction — part 1028
REAR SUSPENSION MEMBER
RSU-25
< UNIT REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
UNIT REMOVAL AND INSTALLATION
REAR SUSPENSION MEMBER
Exploded View
INFOID:0000000011276555
Removal and Installation - FWD
INFOID:0000000011276556
REMOVAL
1. Remove wheel and tires using power tool. Refer to
WT-67, "Removal and Installation"
2. Remove muffler assembly. Refer to
.
3. Remove coil spring. Refer to
RSU-8, "Removal and Installation - FWD"
4. Remove lower link. Refer to
RSU-19, "Removal and Installation"
.
5. Remove upper link. Refer to
RSU-21, "Removal and Installation"
.
6. Remove rear stabilizer.Refer to
RSU-23, "Removal and Installation"
7. Remove rear shock absorber. Refer to
RSU-15, "Removal and Installation"
8. Set suitable jack under rear suspension member.
9. Remove bolts from rear suspension member.
10. Slowly lower suitable jack and remove rear suspension member.
CAUTION:
Secure suspension assembly to a suitable jack while removing it.
INSPECTION AFTER REMOVAL
Check rear suspension member for deformation, cracks, or any other damage. Replace it if necessary.
INSTALLATION
Installation is in the reverse order of the removal.
1.
Rear suspension member
2.
Suspension member stay
(RH)
3.
Suspension member stay (LH)
4.
Bound bumper
Front
ALEIA0214ZZ
RSU-26
< UNIT REMOVAL AND INSTALLATION >
REAR SUSPENSION MEMBER
• When installing suspension member stay, face each arrow on the part toward the inside of the vehicle.
• Align the matching marks made during removal when reusing the disc brake rotor.
• Perform the final tightening of the nuts and bolts under unladen conditions with the tires on level ground.
INSPECTION AFTER INSTALLATION
1. Adjust parking brake operation. Refer to
PB-4, "Inspection and Adjustment"
.
2. Check wheel alignment. Refer to
3. Perform the sensor initialize of the headlamp aiming control system. Refer to
IZE : Special Repair Requirement"
(HALOGEN HEADLAMP) or
EXL-221, "SENSOR INITIALIZE : Special
(LED HEADLAMP).
4. Adjust the neutral position of the steering angle sensor. Refer to
5. Check wheel sensor harness for proper connection. Refer to
.
Removal and Installation - AWD
INFOID:0000000011276557
REMOVAL
1. Remove wheel and tires using power tool. Refer to
WT-67, "Removal and Installation"
2. Remove coil spring. Refer to
RSU-10, "Removal and Installation - AWD"
3. Remove lower link. Refer to
RSU-19, "Removal and Installation"
4. Remove upper link. Refer to
RSU-21, "Removal and Installation"
.
5. Remove rear stabilizer.Refer to
RSU-23, "Removal and Installation"
6. Remove rear final drive. Refer to
DLN-120, "Removal and Installation"
7. Remove rear shock absorber. Refer to
RSU-15, "Removal and Installation"
8. Set suitable jack under rear suspension member.
9. Remove bolts from rear suspension member.
10. Slowly lower suitable jack and remove rear suspension member.
CAUTION:
Secure suspension assembly to a suitable jack while removing it.
INSPECTION AFTER REMOVAL
Check rear suspension member for deformation, cracks, or any other damage. Replace it if necessary.
INSTALLATION
Installation is in the reverse order of the removal.
• When installing suspension member stay, face each arrow on the part toward the inside of the vehicle.
• Align the matching marks made during removal when reusing the disc brake rotor.
• Perform the final tightening of the nuts and bolts under unladen conditions with the tires on level ground.
INSPECTION AFTER INSTALLATION
1. Adjust parking brake operation. Refer to
PB-4, "Inspection and Adjustment"
.
2. Check wheel alignment. Refer to
3. Perform the sensor initialize of the headlamp aiming control system. Refer to
IZE : Special Repair Requirement"
(HALOGEN HEADLAMP) or
EXL-221, "SENSOR INITIALIZE : Special
(LED HEADLAMP).
4. Adjust the neutral position of the steering angle sensor. Refer to
5. Check wheel sensor harness for proper connection. Refer to
.
6. When rear differential gear oil leaks while removing, check oil level after the installation. Refer to
.
SERVICE DATA AND SPECIFICATIONS (SDS)
RSU-27
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment (Unladen*
1
)
INFOID:0000000011276559
*1: Fuel, engine coolant, and lubricants are full. Spare tire, jack, hand tools, and mats are in designated positions.
*2: Since an adjustment mechanism is not included, the value of the left and right wheels must be used as the standard value.
Wheelarch Height (Unladen*)
INFOID:0000000011276560
Unit: mm (in)
*: Fuel, engine coolant, and lubricants are full. Spare tire, jack, hand tools, and mats are in designated positions.
Drive Type
FWD
AWD
Camber
Degree minute (Decimal degree)
Minimum
−1°′40’ (−1.67°)
−1° 20′ (−1.33°)
Nominal
−0° 55′ (−0.92°)
−0° 35′ (−0.58°)
Maximum
−0° 10′ (−0.17°)
0
° 10′ (0.17°)
Total toe-in
Distance (A - B)
Minimum
In 0.0 mm (In 0.00 in)
Nominal
In 4.0 mm (In 0.16 in)
Maximum
In 8.0 mm (In 0.31 in)
Angle (LH and
RH)
*2
Degree minute
(Decimal degree)
Minimum
In 0
° 00′ (In 0.00°)
Nominal
In 0
° 20′ (In 0.33°)
Maximum
In 0
° 40′ (In 0.67°)
SFA234AC
Axle type
FWD
AWD
Body type
2 ROW
3 ROW
2 ROW
3 ROW
Tire size
225/65R17
225/60R18
225/65R17 RF
225/65R17
225/60R18
225/65R17 RF
Front (Hf)
788 (31.02)
790 (31.10)
790 (31.10)
797 (31.38)
799 (31.46)
800 (31.50)
Rear (Hr)
785 (30.91)
787 (30.98)
786 (30.94)
794 (31.26)
796 (31.34)
795 (31.30)
LEIA0085E
SB-1
RESTRAINTS
C
D
E
F
G
I
J
K
L
M
SECTION
SB
A
B
SB
N
O
P
CONTENTS
SEAT BELT
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Seat Belt Service . . . . . . . ...
Precaution for Work . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
BASIC INSPECTION . . . . . . . . .
COMPONENT INSPECTION . . . . . . . ...
Inspection . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
FRONT SEAT BELT . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
SEAT BELT RETRACTOR . . . . . . . . . . ..
SEAT BELT RETRACTOR : Removal and Instal-
lation . . . . . . . . . . . . . . . . . . ..
SEAT BELT HEIGHT ADJUSTER . . . . . . .
SEAT BELT HEIGHT ADJUSTER : Removal and
Installation . . . . . . . . . . . . . . . ...
FRONT SEAT BELT BUCKLE . . . . . . . . ..
FRONT SEAT BELT BUCKLE : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
SECOND ROW SEAT BELT . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
SEAT BELT RETRACTOR . . . . . . . . . .
SEAT BELT RETRACTOR : Removal and Instal-
lation . . . . . . . . . . . . . . . . . .
SEAT BELT BUCKLE . . . . . . . . . . . .
SEAT BELT BUCKLE : Removal and Installation .
THIRD ROW SEAT BELT . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
SEAT BELT RETRACTOR . . . . . . . . . .
SEAT BELT RETRACTOR : Removal and Instal-
lation . . . . . . . . . . . . . . . . . .
SEAT BELT BUCKLE . . . . . . . . . . . .
SEAT BELT BUCKLE : Removal and Installation .
LATCH (LOWER ANCHORS AND TETHER
FOR CHILDREN) SYSTEM . . . . . . . ...
Removal and Installation . . . . . . . . . . .
TOP TETHER STRAP CHILD RESTRAINT . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст