Nissan Rogue. Instruction — part 1122
SRC-38
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORK FLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000011279536
OVERALL SEQUENCE
DETAILED FLOW
AWHIA0555GB
DIAGNOSIS AND REPAIR WORK FLOW
SRC-39
< BASIC INSPECTION >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
1.
INTERVIEW THE CUSTOMER FOR THE SYMPTOM
Interview the customer for the symptom (the condition and the environment when the incident/malfunction
occurs).
>> GO TO 2.
2.
CHECK SYMPTOM
Check the symptom from the customer information.
>> GO TO 3.
3.
CHECK WARNING LAMP OPERATION
Check air bag warning lamp operation in the user mode.
Are any malfunction detected?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK LOW VOLTAGE
Check low voltage with CONSULT.
Are any malfunction detected?
YES
>> GO TO 9.
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
5.
CHECK SELF DIAGNOSTIC RESULT
Check “Self Diagnostic Result” with CONSULT or diagnosis mode.
If it is impossible to switch to diagnosis mode, follow the same procedure that DTC is not detected.
NOTE:
Perform the following procedure if DTC is detected.
• Record DTC (Print them out with CONSULT.)
• Erase “Self Diagnostic Result”.
• Study the relationship between the malfunction that DTC or air bag warning lamp indicates and the symptom
that the customer describes.
• Check related service bulletins for information.
Is DTC detected?
YES
>> GO TO 6.
NO
>> GO TO 7.
6.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the DTC.
>> GO TO 8.
7.
PERFORM DIAGNOSIS ACCORDING TO WARNING LAMP OPERATION
1. Check air bag warning lamp operation in the user mode.
2. Perform Diagnosis Procedure for the air bag warning lamp operation.
>> GO TO 9.
8.
DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Inspect according to Diagnostic Procedure of the DTC.
>> GO TO 9.
9.
REPAIR OR REPLACE THE MALFUNCTION PART
Repair or replace the malfunctioning part.
SRC-40
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORK FLOW
>> GO TO 10.
10.
ON BOARD DIAGNOSIS FUNCTION
Check self diagnostic result and air bag warning lamp operation in the user mode.
Is the malfunction repaired?
YES
>> Inspection End.
NO
>> GO TO 2.
INSPECTION AND ADJUSTMENT
SRC-41
< BASIC INSPECTION >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000011279537
• When replacing the occupant classification system control unit, perform “Zero point reset” procedure. Refer
SRC-41, "ZERO POINT RESET : Special Repair Requirement"
.
• When replacing the air bag diagnosis sensor unit configuration of the air bag diagnosis sensor unit is
SRC-42, "CONFIGURATION : Work Procedure"
ZERO POINT RESET
ZERO POINT RESET : Description
INFOID:0000000011279538
Always perform “Zero point reset” using CONSULT when removing and installing the passenger seat or ser-
vicing the occupant classification system. If zero point reset is not performed the OCS may not operate nor-
mally, which may increase the risk of serious injury in a collision. “Zero point reset” is an initializing procedure
for occupant detection sensor that must be performed when replacing or removing and installing passenger
seat.
If “Zero point reset” is not performed, the initialization is incomplete and Occupant Detection System does not
operate normally.
NOTE:
• When “Zero point reset” is performed once after removal and installation of passenger seat, CONSULT dis-
plays “complete”.
• When reinstalling passenger seat after removal, the initial value for occupant detection sensor changes, and
Occupant Detection System does not operate normally.
• Always perform “Zero point reset” after performing the work as per the following:
- Reinstallation of passenger seat
- Installation of passenger seat that is “Zero point reset” complete
- Installation of passenger seat that is “Zero point reset” in complete
ZERO POINT RESET : Special Repair Requirement
INFOID:0000000011279539
1.
PERFORM ZERO POINT RESET
1. Perform “Zero point reset”.
NOTE:
When performing “Zero point reset”, be careful of the items described as per the following:
• Perform “Zero point reset” after installing passenger seat to the vehicle
• Do not put any objects on passenger seat
• Do not apply excessive vibration to the vehicle
• Do not touch the vehicle
• Do not tilt the vehicle
2. Select start on “Zero point reset function” screen from, “Work support” of CONSULT “OCCUPANT
DETECTION”.
3. “Zero point reset” starts.
>> GO TO 2.
2.
CONFIRMATION OF SETTING
1. Proceed to “Zero point reset function” screen from “Work support” of CONSULT “OCCUPANT DETEC-
TION”.
2. Check that “Complete” or “Incomplete” is displayed on “Zero point reset status”.
CAUTION:
• “Complete” is displayed on “Zero point reset current status” if the seat is reinstalled by seat removal
and installation, or “Zero point reset” is already performed.
• “Zero point reset current status” displays “Incomplete” if a new seat is installed. When turning key
switch ON without performing “Zero point reset”, front passenger air bag OFF indicator turns ON.
When “Zero point reset” is performed, front passenger air bag OFF indicator turns OFF.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст