Nissan Rogue. Instruction — part 263
DAS
C1B95-00 CONTROL MODULE
DAS-223
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1B95-00 CONTROL MODULE
DTC Description
INFOID:0000000011277380
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Chassis control module
FAIL-SAFE
The following functions are suspended:
• Active Trace Control function
• Active Ride Control (brake) function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1B95-00” detected?
YES
>> Proceed to
DAS-223, "Diagnosis Procedure"
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure
INFOID:0000000011277381
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.
2. Turn the ignition switch OFF and wait for 10 seconds or more.
3. Turn the ignition switch ON.
4. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1B95” detected?
YES
>> Replace the chassis control module. Refer to
DAS-286, "Removal and Installation"
.
NO
>> Inspection End.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1B95-00
CONTROL MODULE
(Control module)
When a malfunction is detected in chassis control module.
DAS-224
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1B99-00 CONTROL MODULE
C1B99-00 CONTROL MODULE
DTC Description
INFOID:0000000011277382
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Chassis control module
FAIL-SAFE
The following functions are suspended:
• Active Ride Control function
• Active Trace Control function
• Active Engine Brake function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1B99-00” detected?
YES
>> Proceed to
DAS-224, "Diagnosis Procedure"
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure
INFOID:0000000011277383
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.
2. Turn the ignition switch OFF and wait for 10 seconds or more.
3. Turn the ignition switch ON.
4. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1B99” detected?
YES
>> Replace the chassis control module. Refer to
DAS-286, "Removal and Installation"
.
NO
>> Inspection End.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1B99-00
CONTROL MODULE
(Control module)
When a malfunction is detected in chassis control module.
DAS
C1BA0-00 ADAS/CHASSIS CONTROL BRAKE SYSTEM
DAS-225
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1BA0-00 ADAS/CHASSIS CONTROL BRAKE SYSTEM
DTC Description
INFOID:0000000011277384
DTC DETECTION LOGIC
POSSIBLE CAUSE
• ABS actuator and electric unit (control unit)
• Chassis control module
FAIL-SAFE
The following functions are suspended:
• Active Trace Control function
• Active Ride Control (brake) function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BA0-00” and/or “C1BA7-00”detected?
DAS-225, "Diagnosis Procedure"
YES (“C1BA0-00” and “C1BA7-00”)>>Perform “Self Diagnostic Result” of “ICC/ADAS”.
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure
INFOID:0000000011277385
1.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SYSTEM
With CONSULT
Perform “Self Diagnostic Result” of “ABS”.
Is DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.
2. Turn the ignition switch OFF and wait for 10 seconds or more.
3. Turn the ignition switch ON.
4. Perform “All DTC Reading”.
Is DTC “C1BA0-00”, “U1000-00” or other DTC detected?
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BA0-00
ADAS/CHASSIS CTRL BRAKE
SYS
(ADAS/Chassis Control brake
system)
• When receiving from ABS actuator and electric unit (control unit) that the value
of the brake system signal transmitted from the chassis control module to ABS
actuator and electric unit (control unit) is malfunctioning.
DAS-226
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BA0-00 ADAS/CHASSIS CONTROL BRAKE SYSTEM
YES (“C1BA0-00”)>>Replace the chassis control module. Refer to
DAS-286, "Removal and Installation"
.
YES (“U1000-00”)>>Refer to
DAS-260, "Diagnosis Procedure"
YES (other DTC)>>Check the DTC.
NO
>> Inspection End.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст