Nissan Rogue. Instruction — part 680
FRONT DRIVE SHAFT BOOT
FAX-13
< REMOVAL AND INSTALLATION >
[FWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
FRONT DRIVE SHAFT BOOT
Exploded View
INFOID:0000000011278625
(LH)
(RH)
AWDIA1161ZZ
1.
Shaft
2.
Circular clip
3.
Dust shield
4.
Housing
5.
Snap ring
6.
Spider assembly
7.
Stopper ring
8.
Boot
9.
Boot band
10. Joint sub-assembly
Wheel side
AWDIA1200ZZ
1.
Joint sub-assembly
2.
Circular clip
3.
Boot band
4.
Boot
5.
Shaft
6.
Stopper ring
FAX-14
< REMOVAL AND INSTALLATION >
[FWD]
FRONT DRIVE SHAFT BOOT
WHEEL SIDE
WHEEL SIDE : Removal and Installation
INFOID:0000000011278626
REMOVAL
1. Remove front wheel and tire using power tool. Refer to
WT-67, "Removal and Installation"
2. Remove the bolt (1) and separate the front wheel sensor from
the steering knuckle. Refer to
SOR : Removal and Installation"
.
CAUTION:
• Failure to separate the front wheel sensor from the steer-
ing knuckle may result in damage to the front wheel sen-
sor.
• Pull out the front wheel sensor, being careful to turn it as
little as possible. Do not pull on front wheel sensor har-
ness
3. Remove brake caliper torque member bolts, leaving brake hose attached. Position the brake caliper aside
BR-37, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Exploded View"
(1 PISTON
TYPE), or
BR-42, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Exploded View"
(2 PISTON TYPE).
CAUTION:
Do not depress brake pedal while brake caliper is removed.
4. Put alignment marks (A) on disc brake rotor and wheel hub and
bearing. Remove disc brake rotor.
CAUTION:
Do not drop the disc brake rotor.
5. Remove cotter pin.
6. Remove the nut retainer.
7. Loosen the wheel hub lock nut from the drive shaft using power tool.
8. Using a piece of wood and a suitable tool, tap on the lock nut to
disengage the drive shaft from the wheel hub and bearing.
CAUTION:
• Do not place the drive shaft joint at an extreme angle. Be
careful not to over extend the slide joint.
• Do not allow the drive shaft to hang without support.
NOTE:
Use a suitable puller if drive shaft cannot be separated from the
wheel hub and bearing.
9. Remove the wheel hub lock nut.
10. Remove the engine side cover. Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
7.
Spider assembly
8.
Snap ring
9.
Housing
10. Dust shield
11. Support bearing
12. Bearing retainer
13. Support bearing bracket
Wheel side
A.
Refer to FRONT DRIVE SHAFT IN-
STALLATION
ALDIA0526ZZ
JPDIG0066ZZ
JPDIG0070ZZ
FRONT DRIVE SHAFT BOOT
FAX-15
< REMOVAL AND INSTALLATION >
[FWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
11. Remove the lower nut and bolt from the steering knuckle. Separate the transverse link from the steering
.
12. Separate drive shaft from wheel hub and bearing. Reposition the drive shaft aside with wire. Refer to
.
13. Remove boot bands.
14. Separate boot from joint sub-assembly.
15. Screw a suitable tool (A) 30 mm (1.18 in) or more into threaded
part of joint sub-assembly. Support drive shaft with one hand
and pull out joint sub-assembly with a sliding hammer or suitable
tool from housing assembly.
CAUTION:
• Align sliding hammer or suitable tool and drive shaft and
remove joint sub-assembly by pulling directly.
• If joint sub-assembly cannot be removed after five or
more unsuccessful attempts, replace the entire drive shaft
assembly.
16. Remove circular clip (1) from shaft.
17. Remove outer boot from shaft.
INSPECTION AFTER REMOVAL
Check the following items, and replace the part if necessary.
• Move joint up/down, left/right, and in the axial directions. Check for
motion that is not smooth and for significant looseness.
• Check boot for cracks, damage, and leakage of grease.
INSTALLATION
1. Clean the old grease on joint sub-assembly with paper shop cloth.
2. Fill serration slot joint sub-assembly with Genuine NISSAN Grease.
CAUTION:
After applying grease, use a paper shop cloth to wipe off old grease that has oozed out.
NOTE:
Always check with the Parts Department for the latest parts information.
3. Install boot and boot bands to shaft.
CAUTION:
• Wrap serration on shaft with tape to protect the boot from damage.
• Do not reuse boot and boot band.
4. Remove the tape wrapped around the serration on shaft.
JPDIF0258ZZ
JPDIF0007ZZ
SDIA1190J
FAX-16
< REMOVAL AND INSTALLATION >
[FWD]
FRONT DRIVE SHAFT BOOT
5. Position the circular clip (1) on groove at the shaft edge.
CAUTION:
Do not reuse circular clip.
NOTE:
A drive joint inserter is recommended when installing the circular
clip.
6. Align the shaft and joint sub-assembly. Assemble the shaft with joint sub-assembly while holding the circu-
lar clip.
7. Install joint sub-assembly (1) to shaft using suitable tool.
CAUTION:
Confirm that joint sub-assembly is correctly engaged while
rotating drive shaft.
8. Apply the specified amount of Genuine NISSAN Grease into the large diameter side opening of the boot.
NOTE:
Always check with the Parts Department for the latest parts information.
9. Install the boot securely into grooves (indicated by “*” marks)
shown.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” mark) on the shaft or the joint sub-assembly, boot
may come off. Remove all grease from the boot mounting
surface.
10. Make sure boot installation length (L) is the specified length.
Insert a suitable tool into the large end of boot. Bleed air from
boot to prevent boot deformation.
CAUTION:
• Boot may break if boot installation length is not within standard value.
• Be careful that suitable tool does not contact inside surface of boot.
JPDIF0007ZZ
JPDIF0011ZZ
Grease quantity
: Refer to
.
Boot installation
length (L)
: Refer to
JPDIF0222ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст