Nissan Rogue. Instruction — part 169
C1121, C1123, C1125, C1127 ABS OUT VALVE SYSTEM
BRC-87
< DTC/CIRCUIT DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
C1121, C1123, C1125, C1127 ABS OUT VALVE SYSTEM
DTC Logic
INFOID:0000000011280610
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF DIAGNOSTIC RESULT
With CONSULT.
1. Turn ignition switch OFF to ON.
2. Perform “Self Diagnostic Result”.
Is DTC C1121, C1123, C1125 or C1127 detected?
YES
>> Proceed to diagnosis procedure. Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011280611
Regarding Wiring Diagram information, refer to
1.
CONNECTOR INSPECTION
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) connectors.
3. Check connectors and terminals for deformation, disconnection, looseness or damage.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace as necessary.
2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) BATTERY POWER SUPPLY
Check voltage between ABS actuator and electric unit (control unit) connector E125 terminal 25 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning components.
3.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) GROUND CIRCUIT
Check continuity between ABS actuator and electric unit (control unit) connector E125 terminals 13, 38 and
ground.
DTC
Display Item
Malfunction detected condition
Possible causes
C1121
FR LH OUT ABS SOL
When a malfunction is detected in front LH ABS OUT
valve.
• Harness or connector
• ABS actuator and electric unit
(control unit)
• Fusible link
• Battery power supply system
C1123
FR RH OUT ABS SOL
When a malfunction is detected in front RH ABS OUT
valve.
C1125
RR LH OUT ABS SOL
When a malfunction is detected in rear LH ABS OUT
valve.
C1127
RR RH OUT ABS SOL
When a malfunction is detected in rear RH ABS OUT
valve.
ABS actuator and electric unit (control unit)
—
Voltage
(Approx.)
Connector
Terminal
E125
25
Ground
Battery voltage
BRC-88
< DTC/CIRCUIT DIAGNOSIS >
[VDC/TCS/ABS]
C1121, C1123, C1125, C1127 ABS OUT VALVE SYSTEM
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-134, "Removal and Installa-
.
NO
>> Repair or replace malfunctioning components.
ABS actuator and electric unit (control unit)
—
Continuity
Connector
Terminal
E125
13
Ground
Yes
38
C1130 ENGINE SIGNAL
BRC-89
< DTC/CIRCUIT DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
C1130 ENGINE SIGNAL
DTC Logic
INFOID:0000000011280612
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF DIAGNOSTIC RESULT
With CONSULT.
1. Turn ignition switch OFF to ON.
2. Perform “Self Diagnostic Result”.
Is DTC C1130 detected?
YES
>> Proceed to diagnosis procedure. Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011280613
1.
CHECK SELF DIAGNOSTIC RESULT FOR ENGINE SYSTEM
With CONSULT.
Perform “Self Diagnostic Result”. Refer to
.
Are any ECM DTCs detected?
YES
>> Refer to
.
NO
>> GO TO 2.
2.
CHECK SELF DIAGNOSTIC RESULT FOR ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
With CONSULT.
1. Perform “Self Diagnostic Result” and erase DTCs.
2. Turn ignition switch OFF.
3. Start engine and drive vehicle for a short period of time.
4. Check that malfunction indicator lamp (MIL) turns OFF.
5. Stop vehicle and perform “Self Diagnostic Result”.
Is DTC C1130 detected?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-134, "Removal and Installa-
.
NO
>> Check pin terminals and connection of connectors for abnormal conditions. Repair or replace mal-
functioning components.
DTC
Display Item
Malfunction detected condition
Possible causes
C1130
ENGINE SIGNAL 1
When a malfunction is detected in ECM system.
• ECM
• ABS actuator and electric unit
(control unit)
• CAN communication line
BRC-90
< DTC/CIRCUIT DIAGNOSIS >
[VDC/TCS/ABS]
C1140 ACTUATOR RELAY SYSTEM
C1140 ACTUATOR RELAY SYSTEM
DTC Logic
INFOID:0000000011280614
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULT
With CONSULT.
1. Turn ignition switch OFF to ON.
2. Perform “Self Diagnostic Result”.
Is DTC C1140 detected?
YES
>> Proceed to diagnosis procedure. Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011280615
Regarding Wiring Diagram information, refer to
1.
CONNECTOR INSPECTION
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) connectors.
3. Check connectors and terminals for deformation, disconnection, looseness or damage.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace as necessary.
2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) BATTERY POWER SUPPLY
Check voltage between ABS actuator and electric unit (control unit) connector E125 terminals 1, 25 and
ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning components.
3.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) GROUND CIRCUIT
Check continuity between ABS actuator and electric unit (control unit) connector E125 terminals 13, 38 and
ground.
DTC
Display Item
Malfunction detected condition
Possible causes
C1140
ACTUATOR RLY
When a malfunction is detected in actuator relay.
• Harness or connector
• ABS actuator and electric unit
(control unit)
• Fusible link
• Battery power supply system
ABS actuator and electric unit (control unit)
—
Voltage
(Approx.)
Connector
Terminal
E125
1
Ground
Battery voltage
25
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст