Nissan Rogue. Instruction — part 113
BCS-58
< WIRING DIAGRAM >
[WITH INTELLIGENT KEY SYSTEM]
BCM
AAMIA2833GB
BCS
BCM
BCS-59
< WIRING DIAGRAM >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
AAMIA2136GB
BCS-60
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
INSPECTION AND ADJUSTMENT
BASIC INSPECTION
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM)
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Description
INFOID:0000000011280207
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle specification with CONSULT configuration before replace-
ment.
NOTE:
If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Instruction Configuration” after replac-
ing BCM.
AFTER REPLACEMENT
CAUTION:
• When replacing BCM, you must perform “After Replace ECU” with CONSULT.
- Complete the procedure of “After Replace ECU” in order.
- If you set incorrect “After Replace ECU”, incidents might occur.
- Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• When replacing BCM, perform the system initialization (NATS).
• When replacing BCM, perform “Configuration” of CAN gateway.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Work Proce-
dure
INFOID:0000000011280208
1.
SAVING VEHICLE SPECIFICATION (BCM)
CONSULT
Enter “Re/Programming, Configuration” and perform “Before Replace ECU” to save or print current vehicle
specification.
NOTE:
If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Instruction Configuration” after replac-
ing BCM.
>> GO TO 2.
2.
SAVING VEHICLE SPECIFICATION (CAN GATEWAY)
CONSULT
Perform “READ CONFIGURATION” to save or print current vehicle specification. Refer to
.
NOTE:
If “READ CONFIGURATION” cannot be used, use the “WRITE CONFIGURATION - Instruction selection” after
replacing BCM.
>> GO TO 3.
3.
REPLACE BCM
Replace BCM. Refer to
BCS-75, "Removal and Installation"
>> GO TO 4.
4.
WRITING VEHICLE SPECIFICATION (BCM)
CONSULT
1. Enter “Re/Programming, Configuration”.
2. If “Before Replace ECU” operation was performed, automatically an “Operation Log Selection” screen will
be displayed. Select the applicable file from the “Saved Data List” and press “Confirm” to write vehicle
specification. Refer to
BCS
INSPECTION AND ADJUSTMENT
BCS-61
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
3. If “Before Replace ECU” operation was not performed, select “After Replace ECU” or “Instruction Configura-
tion” to write vehicle specification. Refer to
BCS-61, "CONFIGURATION (BCM) : Work Procedure"
>> GO TO 5.
5.
INITIALIZE BCM (NATS)
Perform BCM initialization. (NATS)
>> GO TO 6.
6.
INITIALIZE TPMS
Perform TPMS initialization. Refer to
>> GO TO 7.
7.
WRITING VEHICLE SPECIFICATION (CAN GATEWAY FUNCTION)
CONSULT
Perform “WRITE CONFIGURATION – Config file” or “WRITE CONFIGURATION – Instruction selection” to write
vehicle specification. Refer to
>> GO TO 8.
8.
REGISTER INTELLIGENT KEYS
For initialization and registration of Intelligent Keys, refer to CONSULT Immobilizer mode and follow the on-
screen instructions.
>> Work End.
CONFIGURATION (BCM)
CONFIGURATION (BCM) : Description
INFOID:0000000011280209
Vehicle specification needs to be written with CONSULT because it is not written after replacing BCM.
Configuration has three functions as follows:
CAUTION:
• When replacing BCM, you must perform “Select Saved Data List” or "After Replace ECU" with CON-
SULT.
• Complete the procedure of “Select Saved Data List” or "After Replace ECU" in order.
• If you set incorrect “Select Saved Data List” or "After Replace ECU", incidents might occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• Never perform “Select Saved Data List” or "After Replace ECU" except for new BCM.
CONFIGURATION (BCM) : Work Procedure
INFOID:0000000011280210
1.
WRITING MODE SELECTION
CONSULT
Select “Reprogramming, Configuration” of BCM.
When writing saved data>>GO TO 2.
When writing instructionly>>GO TO 3.
Function
Description
"Before Replace ECU"
• Reads the vehicle configuration of current BCM.
• Saves the read vehicle configuration.
"After Replace ECU"
Writes the vehicle configuration with instruction selection.
"Select Saved Data List"
Writes the vehicle configuration with saved data.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст