Nissan Rogue. Instruction — part 133
BR-2
BRAKE BOOSTER . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and installation . . . . . . . . . ....
VACUUM LINES . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
FRONT DISC BRAKE . . . . . . . . . .
BRAKE PAD (1 PISTON TYPE) . . . . . . . ...
BRAKE PAD (1 PISTON TYPE) : Exploded View ...
BRAKE PAD (1 PISTON TYPE) : Removal and In-
stallation . . . . . . . . . . . . . . . . .
BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) ...
BRAKE CALIPER ASSEMBLY (1 PISTON TYPE)
: Exploded View . . . . . . . . . . . . . ..
BRAKE CALIPER ASSEMBLY (1 PISTON TYPE)
: Removal and Installation . . . . . . . . . ..
BRAKE PAD (2 PISTON TYPE) . . . . . . . ...
BRAKE PAD (2 PISTON TYPE) : Exploded View ...
BRAKE PAD (2 PISTON TYPE) : Removal and In-
stallation . . . . . . . . . . . . . . . . .
BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) ...
BRAKE CALIPER ASSEMBLY (2 PISTON TYPE)
: Exploded View . . . . . . . . . . . . . ..
BRAKE CALIPER ASSEMBLY (2 PISTON TYPE)
: Removal and Installation . . . . . . . . . ..
REAR DISC BRAKE . . . . . . . . . . ..
BRAKE PAD . . . . . . . . . . . . . . . .
BRAKE PAD : Exploded View . . . . . . . ....
BRAKE PAD : Removal and Installation . . . . .
BRAKE CALIPER ASSEMBLY . . . . . . . .
BRAKE CALIPER ASSEMBLY : Exploded View .
BRAKE CALIPER ASSEMBLY : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
UNIT DISASSEMBLY AND ASSEMBLY ...
FRONT DISC BRAKE . . . . . . . . . ...
BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) ...
BRAKE CALIPER ASSEMBLY (1 PISTON TYPE)
: Exploded View . . . . . . . . . . . . . ..
BRAKE CALIPER ASSEMBLY (1 PISTON TYPE)
: Disassembly and Assembly . . . . . . . . ..
BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) ...
BRAKE CALIPER ASSEMBLY (2 PISTON TYPE)
: Exploded View . . . . . . . . . . . . . ..
BRAKE CALIPER ASSEMBLY (2 PISTON TYPE)
: Disassembly and Assembly . . . . . . . . ..
REAR DISC BRAKE . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
General Specifications . . . . . . . . . . .
Brake Pedal . . . . . . . . . . . . . . .
Brake Booster . . . . . . . . . . . . . . .
Front Disc Brake . . . . . . . . . . . . . .
PRECAUTIONS
BR-3
< PRECAUTION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011279853
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000011279854
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc. to prevent damage to
windshield.
Precaution for Brake System
INFOID:0000000011279855
WARNING:
Clean any dust from the front brake and rear brake with a vacuum dust collector. Do not blow with
compressed air.
CAUTION:
• Brake fluid use refer to
MA-11, "Fluids and Lubricants"
• Do not reuse drained brake fluid.
• Do not spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe
it off immediately and wash with water if it gets on a painted surface.
• Always clean with new brake fluid when cleaning the master cylinder, brake caliper and other com-
ponents.
• Do not use mineral oils such as gasoline or light oil to clean. They may damage rubber parts and
cause improper operation.
• Always loosen the brake tube flare nut with a flare nut wrench.
PIIB3706J
BR-4
< PRECAUTION >
PRECAUTIONS
• Tighten the brake tube flare nut to the specified torque with
flare nut crowfoot (A) and torque wrench (B).
• Always confirm the specified tightening torque when install-
ing the brake pipes.
• Turn the ignition switch OFF and disconnect the ABS actuator
and electric unit (control unit) connector or the battery nega-
tive terminal before performing the work.
• Always connect the battery terminal when moving the vehicle.
• Check that no brake fluid leakage is present after replacing
the parts.
• Check for bends, cracks and damage to the brake pedal.
Adjust brake pedal if it is outside the standard value.
• Burnish the brake contact surfaces after refinishing or replacing rotors, after replacing pads, or if a
soft pedal occurs at very low mileage.
.
- Rear brake: refer to
.
JPFIA0001ZZ
PREPARATION
BR-5
< PREPARATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000011279856
The actual shape of the tools may differ from those illustrated here.
Commercial Service Tool
INFOID:0000000011279857
Tool number
(TechMate No.)
Tool name
Description
—
(J-46532)
Brake height tool
Measuring brake pedal height
38-PFM92
( — )
ProCut™ PFM Series Lathe
Refinishing rotors
LFIA0227E
ALFIA0092ZZ
Tool name
Description
1. Flare nut crowfoot
2. Torque wrench
Tightening brake tube flare nuts
a: 10 mm (0.39 in)/12 mm (0.47 in)
Power tool
Loosening nuts, screws and bolts
S-NT360
PIIB1407E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст