Nissan Rogue. Instruction — part 999
PRECAUTIONS
RAX-3
< PRECAUTION >
[FWD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011280309
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precautions for Drive Shaft
INFOID:0000000011280310
Observe the following precautions when disassembling and assembling drive shaft:
• Do not disassemble joint sub-assembly because it is non-overhaul parts.
• Perform work in a location which is as dust-free as possible.
• Clean the parts before disassembling and assembling.
• Prevent the entry of foreign objects during disassembly.
• Reassemble disassembled parts carefully in the correct order. If work is interrupted, a clean cover must be
placed over parts.
• Use paper shop cloths. Fabric shop cloths must not be used because of the danger of lint adhering to parts.
• Clean disassembled parts (except for rubber parts) with kerosene which shall be removed by blowing with
air or wiping with paper shop cloths.
RAX-4
< PREPARATION >
[FWD]
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000011280311
Tool name
Description
Ball joint remover
Removing wheel stud
Power tools
Loosening nuts, screws, and bolts
NT146
PIIB1407E
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
RAX-5
< SYMPTOM DIAGNOSIS >
[FWD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000011280312
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference
—
Possible cause and SUSPECTED PARTS
Imp
rop
er i
nst
al
la
tio
n,
lo
os
en
es
s
Part
s interf
erence
Whe
e
l be
ari
n
g da
ma
ge
REAR SUSPENSION
TI
RE
WHEE
L
BRAK
E
Symptom
REAR AXLE
Noise
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
Shimmy
×
×
×
×
×
×
Shudder
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
RAX-6
< PERIODIC MAINTENANCE >
[FWD]
REAR WHEEL HUB AND HOUSING
PERIODIC MAINTENANCE
REAR WHEEL HUB AND HOUSING
Inspection
INFOID:0000000011280313
INSPECTION
Make sure the conditions (looseness, back lash) of each component and component conditions (wear, dam-
age) are normal.
WHEEL HUB AND BEARING INSPECTION
• Move wheel hub and bearing in the axial direction by hand. Make sure there is no looseness of wheel bear-
ing.
• Rotate wheel hub, and make sure there is no unusual noise or other irregular conditions. If there is any of
irregular conditions, replace wheel hub and bearing.
Axial end play
: Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст