Nissan Rogue. Instruction — part 894
ENGINE OIL
LU-9
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
Be sure to clean drain plug and install with new drain plug washer.
2. Refill with new engine oil.
Engine oil specification and viscosity: Refer to
MA-11, "Engine Oil Recommendation"
.
CAUTION:
• The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.
• Always use oil level gauge to determine the proper amount of engine oil in engine.
3. Warm up the engine and check area around drain plug and oil filter for engine oil leaks.
4. Stop the engine and wait for 5 minutes.
5. Check the engine oil level. Refer to
.
Tightening torque : Refer to
Engine oil capacity
: Refer to
LU-10
< PERIODIC MAINTENANCE >
OIL FILTER
OIL FILTER
Removal and Installation
INFOID:0000000011277146
REMOVAL
1. Remove fender protector side cover (RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
2. Drain engine oil. Refer to
.
3. Remove oil filter using suitable tool (A)..
WARNING:
Be careful not to burn yourself, as engine oil may be hot.
CAUTION:
• When removing, prepare a shop cloth to absorb any
engine oil leaks or spills.
• Do allow engine oil to adhere to drive belt.
• Completely wipe off any engine oil that adheres to engine
and vehicle.
• Oil filter is provided with relief valve. Use genuine NISSAN
oil filter or equivalent.
INSTALLATION
1. Remove foreign materials adhering to oil filter installation surface.
2. Apply new engine oil to the oil seal contact surface of new oil fil-
ter.
3. Screw oil filter instructionly until it touches the installation surface,
then tighten it by 2/3 turn (A). Or tighten to the specification.
: Front
JPBIA0890ZZ
ALC094
SMA010
Oil filter:
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
JPBIA0077ZZ
OIL FILTER
LU-11
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
Inspection
INFOID:0000000011277147
INSPECTION AFTER INSTALLATION
1. Check the engine oil level. Refer to
.
2. Start the engine, and check that there is are no leaks of engine oil.
3. Stop the engine and wait for at least 5 minutes.
4. Check the engine oil level, and adjust the level (if necessary). Refer to
LU-12
< REMOVAL AND INSTALLATION >
OIL COOLER
REMOVAL AND INSTALLATION
OIL COOLER
Exploded View
INFOID:0000000011277148
Removal and Installation
INFOID:0000000011277149
WARNING:
Be careful not to burn yourself, as engine oil and engine coolant may be hot.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Drain engine coolant. Refer to
2. Remove front air spoiler (RH). Refer to
3. Remove fender protector (RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
4. Disconnect water hoses from the oil cooler.
1.
Intake manifold
2. Cylinder block
3.
Clamp
4.
Water hose
5.
Water hose clip
6.
Water hose
7.
Oil cooler
8.
Gasket
9.
Oil cooler relief valve
Front
A. Refer to INSTALLATION
AWBIA2283ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст