Nissan Rogue. Instruction — part 1138
ST-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011328187
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Service Notice or Precautions for Steering System
INFOID:0000000011280287
• In case of removing steering gear, make the final tightening with grounded and unloaded vehicle condition,
and then check wheel alignment.
• Observe the following precautions when disassembling.
- Before disassembly, thoroughly clean the outside of the unit.
- Disassembly should be done in a clean work area. It is important to prevent the internal parts from becoming
contaminated by dirt or other foreign matter.
- For easier and proper assembly, place disassembled parts in order on a parts rack.
- Use nylon cloth or paper towels to clean the parts; common shop rags can leave lint that might interfere with
their operation.
- Do not reuse non-reusable parts.
- Before assembling, apply the specified grease to the directed parts.
• During quick steering, rasping noise may be heard from around the steering wheel. This is not a malfunction.
The noise is an operating noise of the EPS system under normal conditions. If the rasping noise occurs dur-
ing slow steering, this may not be an operating noise of the system. In this case, it is necessary to find out
the location of the noise and repair, if necessary.
• Do not repeat static steering. (Motor and EPS control unit could be heated.)
PREPARATION
ST-3
< PREPARATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000011280289
The actual shape of the tools may differ from those illustrated here.
Commercial Service Tools
INFOID:0000000011280290
Tool number
(TechMate No.)
Tool name
Description
—
(J-44372)
Pull gauge
Measuring steering wheel turning force, rack
sliding force and ball joint swinging force
KV40107300
(
—
)
Boot band crimping tool
Installing boot bands (large diameter)
LST024
ZZA1229D
Tool name
Description
Steering wheel puller
Removing steering wheel
Ball joint remover
Removing ball joint
ZZA0819D
NT146
ST-4
< PREPARATION >
PREPARATION
Torque wrench
Inspecting of rotating torque for ball joint
and steering column
Power tool
Loosening nuts, screws and bolts
Tool name
Description
ZZA0806D
PIIB1407E
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
ST-5
< SYMPTOM DIAGNOSIS >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000011280291
Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference
—
Possible cause and SUSPECTED PARTS
Out
er/i
nn
er socket
ba
ll j
oi
nt
swin
gi
ng
to
rqu
e
Out
er/i
nn
er
socket ba
ll
jo
in
t rot
a
tin
g torq
ue
Ou
te
r/
in
ne
r so
cke
t
ba
ll jo
in
t
en
d pl
ay
S
tee
rin
g wh
ee
l p
lay
Im
pr
op
er st
ee
ring
whe
e
l
Im
pro
pe
r in
st
al
lat
ion
o
r lo
os
en
es
s
of
tilt
lo
ck
le
ve
r
M
ou
nti
ng
lo
os
en
es
s
S
tee
rin
g c
ol
um
n d
ef
orm
ati
on
or
da
ma
ge
Im
pro
pe
r in
st
al
lat
ion
o
r lo
os
en
es
s
of
ste
eri
ng
co
lu
mn
S
tee
rin
g l
ink
ag
e
loo
sene
ss
PROPELLER SHAFT (A
W
D
)
DIF
F
ERENTIA
L (A
WD)
SUSP
ENSION
AXLE
WHEE
L AND
TIRE
DRIVE
SHAFT
BRAK
E
Symptom
Steering
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
Shudder
×
×
×
×
×
×
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст