Nissan Rogue. Instruction — part 1095
INSPECTION AND ADJUSTMENT
SEC-159
< BASIC INSPECTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000011278558
Refer to the CONSULT Immobilizer mode and follow the on-screen instructions.
ECM RE-COMMUNICATING FUNCTION
ECM RE-COMMUNICATING FUNCTION : Description
INFOID:0000000011278559
Performing following procedure can automatically perform re-communication of ECM and BCM, but only when
the ECM has been replaced with a new one (*1).
*1: New one means an ECM which has never been energized on-board.
(In this step, initialization procedure by CONSULT is not necessary)
NOTE:
• When registering new Key IDs or replacing the ECM that is not brand new, refer to CONSULT Immobi-
lizer mode and follow the on-screen instructions.
• If multiple keys are attached to the key holder, separate them before work.
• Distinguish keys with unregistered key ID from those with registered ID.
ECM RE-COMMUNICATING FUNCTION : Special Repair Requirement
INFOID:0000000011278560
1.
PERFORM ECM RE-COMMUNICATING FUNCTION
1. Install ECM.
2. Using a registered key (*2), turn ignition switch to “ON”.
*2: To perform this step, use the key that has been used before performing ECM replacement.
3. Maintain ignition switch in “ON” position for at least 5 seconds.
4. Turn ignition switch to “OFF”.
5. Start engine.
Can engine be started?
YES
>> Procedure is completed.
NO
>> Initialize control unit. Refer to CONSULT Immobilizer mode and follow the on-screen instructions.
2015 Rogue NAM
SEC-160
< BASIC INSPECTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
KEYFOB ID REGISTRATION
KEYFOB ID REGISTRATION
Description
INFOID:0000000011278561
Perform system initialization when replacing BCM, replacing keyfob or registering an additional keyfob. Refer
to the CONSULT Immobilizer mode and follow the on-screen instructions.
2015 Rogue NAM
P1610 LOCK MODE
SEC-161
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
DTC/CIRCUIT DIAGNOSIS
P1610 LOCK MODE
Description
INFOID:0000000011278563
ECM forcibly switches to the mode that inhibits engine start, when engine start operation is performed 5 times
or more while communication between ECM and BCM is not normal.
DTC Logic
INFOID:0000000011278564
DTC DETECTION LOGIC
NOTE:
• If DTC B1610 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B1610 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check DTC in “Self Diagnostic Result” of “ENGINE” using CONSULT.
Is DTC detected?
YES
>> Go to
SEC-161, "Diagnosis Procedure"
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011278565
1.
CHECK ENGINE START FUNCTION
1. Check that there are no DTC’s except for DTC P1610 detected.
If detected, erase the DTC after fixing.
2. Turn ignition switch OFF.
3. Insert the registered key into the ignition switch and wait 5 seconds.
4. Turn ignition switch ON.
5. Turn ignition switch OFF and wait 5 seconds.
6. Repeat steps 3 and 5 twice (a total of 3 times).
7. Check that engine can start.
>> Inspection End.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1610
LOCK MODE
When ECM detects a communication malfunction between
ECM and BCM 5 times or more.
—
2015 Rogue NAM
SEC-162
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
P1611 ID DISCORD, IMMU-ECM
P1611 ID DISCORD, IMMU-ECM
DTC Logic
INFOID:0000000011278566
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check DTC in “Self Diagnostic Result” of “ENGINE” using CONSULT.
Is DTC detected?
YES
>> Go to
SEC-162, "Diagnosis Procedure"
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011278567
1.
PERFORM INITIALIZATION
Perform initialization of BCM and reregistration of all keys using CONSULT. Refer to the CONSULT Immobi-
lizer mode and follow the on-screen instructions.
Can the system be initialized and can the engine be started with reregistered key?
YES
>> Inspection End.
NO
>> GO TO 2.
2.
CHECK SELF DIAGNOSTIC RESULT
1. Select “Self Diagnostic Result” of “ENGINE” using CONSULT.
2. Erase DTC.
3. Perform DTC CONFIRMATION PROCEDURE for DTC P1611. Refer to
.
Is DTC detected?
YES
>> GO TO 3.
NO
>> Inspection End.
3.
REPLACE BCM
1. Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all keys using CONSULT. Refer to the CONSULT Immobi-
lizer mode and follow the on-screen instructions.
Can the system be initialized and can the engine be started with registered key?
YES
>> Inspection End.
NO
>> GO TO 4.
4.
REPLACE ECM
1. Replace ECM. Refer to
EC-502, "Removal and Installation"
2. Perform “ADDITIONAL SERVICE WHEN REPLACING ECM”. Refer to
>> Inspection End.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1611
ID DISCORD, IMMU-ECM
The ID verification results between BCM
and ECM are NG.
• Harness or connectors
(The CAN communication line is open
or shorted.)
• BCM
• ECM
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст