Nissan Rogue. Instruction — part 807
MAP LAMP ASSEMBLY
INL-55
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
REMOVAL AND INSTALLATION
MAP LAMP ASSEMBLY
Exploded View
INFOID:0000000011279222
Removal and Installation
INFOID:0000000011279223
REMOVAL
1. Lower front edge of map lamp assembly (1) down from the
headlining by releasing the metals clips, then slide forward to
clear pawls at rear.
: Metal clip
: Pawl
2. Disconnect the harness connectors from map lamp assembly and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
1.
Headlining
2.
Map lamp assembly bracket
(without moonroof)
3.
Map lamp assembly bracket
(with moonroof)
4.
Moonroof switch finisher
5.
Map lamp assembly
6.
Map lamp
Metal clip
Clip
Pawl
Front
AWLIA2502ZZ
ALLIA1150ZZ
INL-56
< REMOVAL AND INSTALLATION >
MAP LAMP ASSEMBLY
Visually check the metal clips and pawls for deformation and damage during installation. Replace if
necessary.
Bulb Replacement
INFOID:0000000011279224
NOTE:
The map lamp bulbs are replaced as part of the map lamp.
REMOVAL
1. Remove the map lamp assembly. Refer to
INL-55, "Removal and Installation"
.
2. Remove screws (A) from map lamp (2).
3. Release pawls and remove map lamp from the map lamp
assembly (1).
: Pawl
INSTALLATION
Installation is in the reverse order of removal.
ALLIA1568ZZ
VANITY MIRROR LAMP
INL-57
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
VANITY MIRROR LAMP
Exploded View
INFOID:0000000011279225
Removal and Installation
INFOID:0000000011279226
CAUTION:
Do not attempt to separate the vanity lamp from the sun visor or damage to the components may
occur.
The vanity lamp is replaced as part of the sun visor. Refer to
Bulb or Lens Replacement
INFOID:0000000011279227
WARNING:
Do not touch the glass surface of a bulb while it is lit or right after being turned OFF to prevent burns.
CAUTION:
• Do not touch the glass of bulb directly by hand. Keep grease and other oily substances away from
bulb surface.
• Do not leave bulb out of lamp reflector for a long time because dust, moisture, smoke, etc. may
affect the performance of lamp.
• Do not attempt to separate the vanity lamp from the sun visor or damage to the components may
occur.
1. Insert a suitable tool into the gap between the lens and vanity mirror lamp, then release the lens pawls
and remove.
2. Grasp the vanity mirror lamp bulb and pull straight out of the vanity mirror lamp to remove.
3. Install vanity mirror lamp bulb to vanity mirror lamp.
4. Install the vanity mirror lamp lens.
1.
Lens
2.
Bulb
Pawl
ALLIA1083ZZ
INL-58
< REMOVAL AND INSTALLATION >
ROOM LAMP
ROOM LAMP
Removal and Installation
INFOID:0000000011279229
WARNING:
Do not touch the glass surface of a bulb while it is lit or right after being turned OFF to prevent burns.
CAUTION:
• Do not touch the glass of bulb directly by hand. Keep grease and other oily substances away from
bulb surface.
• Do not leave bulb out of reflector for a long time because moisture, smoke, etc. may affect the per-
formance of lamp.
REMOVAL
1. Lower lens (1) and room lamp as an assembly by releasing
room lamp metal clips (A) using a suitable tool.
2. Disconnect the harness connector from the room lamp and
remove.
INSTALLATION
Installation is in the reverse order of removal.
Bulb Replacement
INFOID:0000000011279230
WARNING:
Do not touch the glass surface of a bulb while it is lit or right after being turned OFF to prevent burns.
CAUTION:
• Do not touch the glass of bulb directly by hand. Keep grease and other oily substances away from
bulb surface.
• Do not leave bulb out of reflector for a long time because moisture, smoke, etc. may affect the per-
formance of lamp.
1. Remove lens (1) by inserting suitable tool and releasing LH side
(switch side) first.
2. Remove room lamp bulb (2).
3. Install room lamp bulb (2).
4. Install room lamp lens (1).
NOTE:
Insert the lens hook end (RH side) first to install lens.
PKIC1049E
PKIC1048E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст