Nissan Rogue. Instruction — part 350
DLK-242
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
Unit: mm (in)
HEIGHT ADJUSTMENT
1. Loosen the hood lock assembly bolts.
2. Adjust the surface height of hood assembly to front grille and front fender according to the specified val-
ues by rotating hood bumper rubber.
3. Temporarily tighten hood lock assembly bolts.
4. Adjust (A) and (B) as shown to the following value with hood's own weight by dropping it from approxi-
mately 200 mm (7.87 in) height or by pressing hood lightly [approximately 29 N (3.0 kg, 6.5 lb)].
5. After adjustment, tighten hood hinge nuts and bolts to the specified torque.
CAUTION:
• Check hood hinge rotating part for poor lubrication. If necessary, apply a suitable multi-purpose
grease.
• After adjusting, apply touch-up paint (body color) to the head of hood hinge bolts and nuts.
CLEARANCE ADJUSTMENT
1. Loosen hood hinge nuts and bolts.
2. Loosen the hood lock assembly bolts.
3. Adjust the hood assembly so the clearance measurements are within specifications.
4. Tighten the hood hinge nuts and bolts to specified torque.
5. Tighten the hood lock assembly bolts to specified torque.
HOOD HINGE
HOOD HINGE : Removal and Installation
INFOID:0000000011278998
REMOVAL
1. Remove hood assembly. Refer to
DLK-240, "HOOD ASSEMBLY : Removal and Installation"
Portion
Section
Item
Measurement
Standard
Parallelism
Hood - Fender
A - A
D
Surface height
0.0
± 1.0 (0.0 ± 0.04)
1.4 (0.06)
E
Clearance
3.5
± 1.5 (0.14 ± 0.04)
1.4 (0.06)
Fender - Front combination lamp
B - B
F
Clearance
9.0
± 2.0 (0.35 ± 0.08)
2.0 (0.08)
Hood - Front combination lamp
C - C
G
Clearance
1.9
± 1.1 (0.07 ± 0.04)
1.5 (0.06)
1.
Secondary striker
2.
Primary striker
3.
Hood assembly
A.
20 mm (0.79 in)
B.
6.8 mm (0.27 in)
AWKIA2925ZZ
2015 Rogue NAM
HOOD
DLK-243
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. Remove front fender. Refer to
DLK-245, "Removal and Installation"
3. Remove hood hinge bolts, and then remove hood hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Before installing the hood hinge, apply anticorrosive agent onto the surface of the vehicle.
• After installation, perform hood assembly adjustment procedure. Refer to
2015 Rogue NAM
DLK-244
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
RADIATOR CORE SUPPORT
RADIATOR CORE SUPPORT
Exploded View
INFOID:0000000011278999
Removal and Installation
INFOID:0000000011279000
CAUTION:
When removing radiator core support upper, be careful not to damage the painted surface.
REMOVAL
Radiator Core Upper Support
1. Remove front combination lamp (LH). Refer to
EXL-119, "Removal and Installation"
2. Remove front air duct. Refer to
3. Remove hood lock. Refer to
DLK-260, "HOOD LOCK : Removal and Installation"
4. Remove secondary latch. Refer to
DLK-261, "SECONDARY LATCH : Removal and Installation"
.
5. Remove crash zone sensor. Refer to
SR-22, "Removal and Installation"
.
6. Remove bolts and radiator core upper support.
Radiator Core Lower Support
1. Remove front bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
2. Support the radiator using a suitable tool.
3. Remove bolts and radiator core lower support.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Tighten bolts to specified torque. Refer to
.
1.
Radiator core upper support
2.
Secondary latch bracket
3.
Radiator core lower support
ALKIA3498ZZ
2015 Rogue NAM
FRONT FENDER
DLK-245
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT FENDER
Exploded View
INFOID:0000000011279001
Removal and Installation
INFOID:0000000011279002
CAUTION:
Use a shop cloths to protect the body from being damaged during removal and installation.
REMOVAL
1. Remove front bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
2. Remove front combination lamp. Refer to
EXL-119, "Removal and Installation"
(HALOGEN HEADLAMP)
EXL-266, "Removal and Installation"
. (LED HEADLAMP).
3. Remove center mudguard. Refer to
EXT-35, "Removal and Installation - Center Mudguard"
.
4. Remove screws (A) and front fender bracket (1).
5. Remove bolts and front fender.
CAUTION:
Use care when removing the front fender. The front fender baffle foam adheres the front fender to
the body side outer. Carefully release the baffle foam or damage to the front fender may occur.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation apply touch up paint (body color) to the head of front fender bolts.
• After installation, adjust the following components as necessary:
- Hood assembly: Refer to
DLK-241, "HOOD ASSEMBLY : Adjustment"
.
- Front door: Refer to
DLK-248, "DOOR ASSEMBLY : Adjustment"
.
1.
Front fender
AWKIA2926ZZ
ALKIA3354ZZ
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст