Nissan Rogue. Instruction — part 52
AV-200
< REMOVAL AND INSTALLATION >
[NAVIGATION WITHOUT BOSE]
AV CONTROL UNIT
REMOVAL AND INSTALLATION
AV CONTROL UNIT
Exploded View
INFOID:0000000011276882
Removal and Installation
INFOID:0000000011276883
REMOVAL
CAUTION:
• Before disconnecting the AV control unit and battery terminals, turn the ignition switch OFF and wait
at least 30 seconds.
• Before replacing AV control unit, perform “READ CONFIGURATION” to save current vehicle specifi-
cation. Refer to
AV-132, "CONFIGURATION (AV CONTROL UNIT) : Configuration List"
NOTE:
After the ignition switch is turned OFF, the AV control unit continues operating for approximately 30 seconds.
Therefore, data corruption may occur if battery voltage is cut off within 30 seconds.
1. Disconnect the negative battery terminal. Refer to
PG-78, "Removal and Installation (Battery)"
2. Remove cluster lid C. Refer to
IP-22, "Removal and Installation"
3. Remove instrument finisher B. Refer to
IP-16, "INSTRUMENT FINISHER B : Removal and Installation"
.
4. Remove instrument finisher E. Refer to
IP-16, "INSTRUMENT FINISHER E : Removal and Installation"
.
5. Remove the AV control unit screws, then pull out the AV control unit.
6. Disconnect the harness connectors from the AV control unit and remove.
7. Remove the AV control unit bracket (LH/RH) screws and the AV control unit brackets (LH/RH) (if neces-
sary).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
1.
AV control unit bracket (LH)
2.
AV control unit
3.
AV control unit bracket (RH)
AWNIA3339ZZ
AV
AV CONTROL UNIT
AV-201
< REMOVAL AND INSTALLATION >
[NAVIGATION WITHOUT BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
• When replacing AV control unit, perform "WRITE CONFIGURATION". Refer to
TION (AV CONTROL UNIT) : Configuration List"
• When replacing AV control unit, the AV control unit must be registered. Refer to
AV-202
< REMOVAL AND INSTALLATION >
[NAVIGATION WITHOUT BOSE]
STEERING SWITCH
STEERING SWITCH
Exploded View
INFOID:0000000011276884
Removal and Installation
INFOID:0000000011276885
REMOVAL
NOTE:
The steering switches are serviced as an assembly.
1. Remove steering wheel. Refer to
ST-11, "Removal and Installation"
.
2. Release pawls on the steering wheel rear finisher and remove.
3. Remove screws (A) and release pawls (B) and remove steering
switches (1) from steering wheel (2).
:
Pawls
INSTALLATION
Installation is in the reverse order of removal.
1.
Steering wheel rear finisher
2.
Steering wheel
3.
Steering switches
Pawl
AWNIA3722ZZ
AWNIA3723ZZ
AV
FRONT TWEETER
AV-203
< REMOVAL AND INSTALLATION >
[NAVIGATION WITHOUT BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
FRONT TWEETER
Removal and Installation
INFOID:0000000011276886
REMOVAL
1. Remove defroster grille. Refer to
VTL-12, "DEFROSTER GRILLE : Removal and Installation"
.
2. Release pawls and pull out the front tweeter (1) from the instru-
ment panel assembly (2).
: Pawl
: Front
3. Disconnect the harness connector from the front tweeter and
remove.
INSTALLATION
Installation is in the reverse order of removal.
ALNIA1663ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст