Nissan Rogue. Instruction — part 689
FRONT WHEEL HUB
FAX-49
< REMOVAL AND INSTALLATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
• Place a washer (A) as shown to install the wheel studs (1) by using
the tightening force of the nut (B).
CAUTION:
Check that there is no clearance between the wheel stud and
the wheel hub and bearing.
• Clean the mating surfaces of the wheel hub lock nut and the wheel hub and bearing.
CAUTION:
Do not apply lubricating oil to these mating surfaces.
• Clean the mating surfaces of the joint sub-assembly and the wheel
hub and bearing. Apply Molykote M77 lubricant to the surface (A)
of the joint sub-assembly.
CAUTION:
Apply lubricant to cover the entire flat mating surface of the
joint sub-assembly.
NOTE:
Always check with the Parts Department for the latest parts infor-
mation.
• Hold the wheel hub and bearing using a suitable tool. Tighten the wheel hub lock nut.
CAUTION:
• Since the drive shaft is assembled by press-fitting, use a torque wrench to tighten the wheel hub
lock nut. Do not use a power tool.
• Too much torque causes axle noise. Too little torque causes wheel bearing looseness. Tighten the
wheel hub lock nut to the specification.
• When installing a the cotter pin (1) and the nut retainer (2),
securely bend the cotter pin to prevent rattles.
• Align the matching marks (A) on the disc brake rotor and on the
wheel hub and bearing.
INSPECTION AFTER INSTALLATION
• Check the wheel alignment. Refer to
.
JPDIF0300ZZ
JPDIG0122ZZ
JPDIF0295ZZ
JPDIG0066ZZ
FAX-50
< REMOVAL AND INSTALLATION >
[AWD]
FRONT WHEEL HUB
• Adjust neutral position of steering angle sensor. Refer to
.
FRONT DRIVE SHAFT BOOT
FAX-51
< REMOVAL AND INSTALLATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
FRONT DRIVE SHAFT BOOT
Exploded View
INFOID:0000000011278650
(LH)
(RH)
AWDIA1161ZZ
1.
Shaft
2.
Circular clip
3.
Dust shield
4.
Housing
5.
Snap ring
6.
Spider assembly
7.
Stopper ring
8.
Boot
9.
Boot band
10. Joint sub-assembly
Wheel side
AWDIA1206ZZ
1.
Joint sub-assembly
2.
Circular clip
3.
Boot band
4.
Boot
5.
Shaft
6.
Stopper ring
7.
Spider assembly
8.
Snap ring
9.
Housing
FAX-52
< REMOVAL AND INSTALLATION >
[AWD]
FRONT DRIVE SHAFT BOOT
WHEEL SIDE
WHEEL SIDE : Removal and Installation
INFOID:0000000011278651
REMOVAL
1. Remove front wheel and tire using power tool. Refer to
WT-67, "Removal and Installation"
2. Remove the bolt (1) and separate the front wheel sensor from
the steering knuckle. Refer to
SOR : Removal and Installation"
.
CAUTION:
• Failure to separate the front wheel sensor from the steer-
ing knuckle may result in damage to the front wheel sen-
sor.
• Pull out the front wheel sensor, being careful to turn it as
little as possible. Do not pull on front wheel sensor har-
ness
3. Remove brake caliper torque member bolts, leaving brake hose attached. Position the brake caliper aside
BR-37, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Exploded View"
(1 PISTON
TYPE), or
BR-42, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Exploded View"
(2 PISTON TYPE).
CAUTION:
Do not depress brake pedal while brake caliper is removed.
4. Put alignment marks (A) on disc brake rotor and wheel hub and
bearing. Remove disc brake rotor.
CAUTION:
Do not drop the disc brake rotor.
5. Remove cotter pin.
6. Remove the nut retainer.
7. Loosen the wheel hub lock nut from the drive shaft using power tool.
8. Using a piece of wood and a suitable tool, tap on the lock nut to
disengage the drive shaft from the wheel hub and bearing.
CAUTION:
• Do not place the drive shaft joint at an extreme angle. Be
careful not to over extend the slide joint.
• Do not allow the drive shaft to hang without support.
NOTE:
Use a suitable puller if drive shaft cannot be separated from the
wheel hub and bearing.
9. Remove the wheel hub lock nut.
10. Remove the engine side cover. Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
11. Remove the lower nut and bolt from the steering knuckle. Separate the transverse link from the steering
knuckle. Refer to
10. Dust shield
11. Support bearing
12. Bearing retainer
13. Support bearing bracket
Wheel side
A.
Refer to FRONT DRIVE SHAFT IN-
STALLATION
ALDIA0526ZZ
JPDIG0066ZZ
JPDIG0070ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст