Nissan Rogue. Instruction — part 1115
SRC-10
< SYSTEM DESCRIPTION >
SYSTEM
SYSTEM
SRS AIR BAG SYSTEM
SRS AIR BAG SYSTEM : System Description
INFOID:0000000011279526
SYSTEM DIAGRAM
DESCRIPTION
• The air bag deploys if the air bag diagnosis sensor unit is activated while the ignition switch is in the ON or
START position.
• The collision modes for which supplemental restraint systems are activated are different among the SRS
systems. For example, the driver air bag module, front passenger air bag module and front seat belt pre-ten-
sioners are activated in a frontal collision but not in a side collision.
SRS Collision Modes
OCCUPANT CLASSIFICATION SYSTEM
AWHIA0629GB
SRS configuration
Frontal collision
Left side collision
Right side collision
Driver air bag module
x
—
—
Front passenger air bag module
x
—
—
Front LH seat belt pre-tensioner
x
—
—
Front RH seat belt pre-tensioner
x
—
—
Front LH side air bag module
—
x
—
Front RH side air bag module
—
—
x
LH side curtain air bag module
—
x
—
RH side curtain air bag module
—
—
x
SYSTEM
SRC-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
OCCUPANT CLASSIFICATION SYSTEM : System Description
INFOID:0000000011279527
SYSTEM DIAGRAM
DESCRIPTION
The occupant classification system (OCS) identifies different size occupants, out of position occupants, and
detects if child seat is present in the front passenger seat. The OCS control unit (2) receives inputs from the
occupant classification sensors (1) (located on the passenger seat track assembly). Depending on classifica-
tion of the passenger, the OCS sends a signal to the air bag diagnosis sensor unit. The air bag diagnosis sen-
sor unit uses this signal and the seat belt buckle switch RH signal to determine deployment or non deployment
of the passenger front air bag in the event of a collision. Depending on the signals received, the air bag diag-
nosis sensor unit can disable the passenger front air bag completely. The OCS (weight sensors) must be set
to zero point using CONSULT after servicing the OCS system.
NOTE:
• CONSULT can be used to confirm when “zero point reset” for OCS is complete.
• Always perform zero point reset after the removal and installation of the seat or when disconnecting the
OCS control unit harness connector even if zero point reset has been completed in the past.
• If zero point reset is incomplete, the passenger air bag will be disabled and the passenger air bag off indica-
tor will be ON.
• In case of customer concern, CONSULT can be used to confirm the passenger air bag status (readiness).
Passenger Air Bag Status Conditions
NOTE:
ALHIA0367GB
Front Passenger Seat
(Condition)
PASS AIR BAG OFF Indicator
(Status)
Passenger Air Bag Status
(Readiness)
CONSULT Display
Seat occupied
OFF
Active (enabled)
ON
Seat occupied
NOTE
ON
Deactivated (disabled)
OFF
Seat empty
OFF
Deactivated (disabled)
OFF
SRC-12
< SYSTEM DESCRIPTION >
SYSTEM
Passenger does not meet Occupant Classification System specifications for passenger air bag activation.
SEAT BELT WARNING LAMP SYSTEM
SEAT BELT WARNING LAMP SYSTEM : System Description
INFOID:0000000011279528
SYSTEM DIAGRAM
AWHIA0610ZZ
AWHIA0694GB
SYSTEM
SRC-13
< SYSTEM DESCRIPTION >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
The seat belt warning lamp (1) will remind the driver if the driver or
front passenger seat belt should be buckled. The system works in
conjunction with the occupant classification system. Refer to
11, "OCCUPANT CLASSIFICATION SYSTEM : System Descrip-
.
Seat Belt Warning System Operation
AWHIA0617ZZ
Driver seat status
(Ignition switch ON)
Passenger seat status
Seat belt buckle switch
LH status
Seat belt buckle switch
RH status
Seat belt warning lamp
Seat occupied
Seat occupied
Buckled
Buckled
Off
Unbuckled
On
Seat unoccupied
—
Off
—
Unbuckled
On
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст