Nissan Rogue. Instruction — part 228
DAS
ACTION TEST
DAS-83
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
- System description for LDW: Refer to
DAS-15, "LDW : System Description"
- System description for BSW: Refer to
DAS-19, "BSW : System Description"
- System description for MOD: Refer to
DAS-25, "MOD : System Description"
- System description for FCW: Refer to
DAS-28, "FCW : System Description"
- Handling precaution: Refer to
DAS-35, "Precautions for Forward Collision Warning"
.
FCW : Inspection Procedure
INFOID:0000000011505729
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- Precautions: Refer to
DAS-9, "Precautions for Driver Assistance Systems"
.
- System description for LDW: Refer to
DAS-15, "LDW : System Description"
- System description for BSW: Refer to
DAS-19, "BSW : System Description"
- System description for MOD: Refer to
DAS-25, "MOD : System Description"
- System description for FCW: Refer to
DAS-28, "FCW : System Description"
- Handling precaution: Refer to
DAS-35, "Precautions for Forward Collision Warning"
.
1.
CHECK FCW SYSTEM SETTING
1. Start the engine.
2. Check that the FCW system setting can be enabled/disabled on the vehicle information display.
3. Turn OFF the ignition switch and wait for 30 seconds or more.
4. Check that the previous setting is saved when the engine starts again.
>> GO TO 2.
2.
ACTION TEST FOR FCW
1. Enable the setting of the FCW system on the vehicle information display.
2. Turn warning systems switch ON (warning systems ON indicator is ON).
3. Check the FCW operation according to the following table:
NOTE:
Vehicle condition/ Driver's operation
Action
Warning sys-
tems ON indi-
cator
Indication on the combination
meter
Buzzer
Less than Ap-
prox. 10 MPH
(15 km/h)
—
No action
ON
FCW indicator (white) ON steady
—
Approx. 10
MPH (15 km/h
or more
Vehicle is not detected
No action
ON
FCW indicator (white) ON steady
OFF
Vehicle is detected
• Warning buzzer
sounds
• Warning lamp
blinks
ON
FCW indicator (white) ON blinks
Short continu-
ous beeps
AWOIA0096ZZ
AWOIA0096ZZ
AWOIA0096ZZ
DAS-84
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
ACTION TEST
If the vehicle speed exceeds approximately 10 MPH (15 km/h), FCW function operates until the vehicle speed
becomes lower than approximately 10 MPH (15 km/h).
>> Inspection End.
DAS
ADDITIONAL SERVICE WHEN REPLACING AROUND VIEW MONITOR CON-
TROL UNIT
DAS-85
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
ADDITIONAL SERVICE WHEN REPLACING AROUND VIEW MONITOR
CONTROL UNIT
Description
INFOID:0000000011444769
BEFORE REPLACEMENT
When replacing around view monitor control unit, save or print current vehicle specification with CONSULT
configuration before replacement.
NOTE:
If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Instruction Configuration” after replac-
ing around view monitor control unit.
AFTER REPLACEMENT
CAUTION:
When replacing around view monitor control unit, you must perform “After Replace ECU” with CON-
SULT.
• Complete the procedure of “After Replace ECU” in order.
• If you set incorrect “After Replace ECU”, incidents might occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
Work Procedure
INFOID:0000000011444770
1.
SAVING VEHICLE SPECIFICATION
-CONSULT
Enter “Re/Programming, Configuration” and perform “Before Replace ECU” to save or print current vehicle
specification.
NOTE:
If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Instruction Configuration” after replac-
ing around view monitor control unit.
>> GO TO 2.
2.
REPLACE AROUND VIEW MONITOR CONTROL UNIT
Replace around view monitor control unit. Refer to
AV-380, "Removal and Installation"
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
CONSULT
1. Enter "Re/Programming, Configuration".
2. If “Before Replace ECU” operation was performed, automatically an "Operation Log Selection" screen will
be displayed. Select the applicable file from the "Saved Data List" and press “Confirm” to write vehicle
specification. Refer to
.
3. If “Before Replace ECU” operation was not performed, select "After Replace ECU" or "Instruction Configura-
tion" to write vehicle specification. Refer to
>> GO TO 4.
4.
OPERATION CHECK
Check that the operation of the around view monitor control unit and camera images (fixed guide lines and
predictive course lines) are normal.
>> Work End.
DAS-86
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)
Description
INFOID:0000000011444771
Vehicle specification needs to be written with CONSULT because it is not written after replacing around view
monitor control unit.
Configuration has three functions as follows:
CAUTION:
• When replacing around view monitor control unit, you must perform “Select Saved Data List” or
"After Replace ECU" with CONSULT.
• Complete the procedure of “Select Saved Data List” or "After Replace ECU" in order.
• If you set incorrect “Select Saved Data List” or "After Replace ECU", incidents might occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• Never perform “Select Saved Data List” or "After Replace ECU" except for new around view monitor
control unit.
Work Procedure
INFOID:0000000011444772
1.
WRITING MODE SELECTION
CONSULT
Select “Reprogramming, Configuration” of around view monitor control unit.
When writing saved data>>GO TO 2.
When writing instructionly>>GO TO 3.
2.
PERFORM “SAVED DATA LIST”
CONSULT
Automatically “Operation Log Selection” window will display if “Before Replace ECU” was performed. Select
applicable file from the “Save Data List” and press “Confirm”.
>> Work End.
3.
PERFORM “AFTER REPLACE ECU” OR “MANUAL CONFIGURATION”
CONSULT
1. Select “After Replace ECU” or “Instruction Configuration”.
2. Identify the correct model and configuration list. Refer to
3. Confirm and/or change setting value for each item.
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally
if the setting is not correct.
4. Select “Next”.
CAUTION:
Make sure to select “Next”, confirm each setting value and press “OK” even if the indicated con-
figuration of brand new around view monitor control unit is same as the desirable configuration. If
not, configuration which is set automatically by selecting vehicle model can not be memorized.
5. When "Completed", select "End".
>> GO TO 4.
4.
OPERATION CHECK
Function
Description
"Before Replace ECU"
• Reads the vehicle configuration of current around view monitor control unit.
• Saves the read vehicle configuration.
"After Replace ECU"
Writes the vehicle configuration with instruction selection.
"Select Saved Data List"
Writes the vehicle configuration with saved data.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст