Nissan Rogue. Instruction — part 653
B1C07 AIMING MOTOR DRIVE SIGNAL
EXL-241
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
B1C07 AIMING MOTOR DRIVE SIGNAL
DTC Logic
INFOID:0000000011280871
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF DIAGNOSTIC RESULT
With
CONSULT.
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result”.
Is DTC B1C07 detected?
YES
>> Proceed to diagnosis procedure. Refer to
EXL-241, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011280872
1.
CHECK HEADLAMP AIMING MOTOR DRIVE SIGNAL SHORT CIRCUIT TO GROUND
1. Disconnect LH and RH headlamp aiming motor connectors and IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK HEADLAMP AIMING MOTOR DRIVE SIGNAL SHORT CIRCUIT TO BATTERY VOLTAGE
Check the voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK HEADLAMP AIMING MOTOR DRIVE SIGNAL SHORT CIRCUIT TO BATTERY VOLTAGE
1. Reconnect IPDM E/R connector.
2. Check the voltage between IPDM E/R harness connector and ground.
DTC
Display Item
Malfunction detected condition
Possible causes
B1C07
AIMING MOTOR DRIVE SIGNAL
[CIRC SHORT TO GRND]
• DC motor circuit short to ground
• DC motor circuit short to supply voltage
• Front combination lamp harness
• IPDM E/R
AIMING MOTOR DRIVE SIGNAL
[CIRC SHORT TO BATTERY]
AIMING MOTOR DRIVE SIGNAL
[SIGNAL COMPARE FAILURE]
IPDM E/R
Ground
Continuity
Connector
Terminal
E218
64
No
IPDM E/R
Ground
Voltage
(Approx.)
Connector
Terminal
E218
64
0 V
IPDM E/R
Ground
Voltage
(Approx.)
Connector
Terminal
E218
64
0 V
EXL-242
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
B1C07 AIMING MOTOR DRIVE SIGNAL
Is the inspection result normal?
YES
>> Refer to
GI-44, "Intermittent Incident"
.
NO
>> Replace IPDM E/R. Refer to
B20CB DAYTIME RUNNING LIGHT LH POWER SUPPLY CIRCUIT
EXL-243
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
B20CB DAYTIME RUNNING LIGHT LH POWER SUPPLY CIRCUIT
DTC Logic
INFOID:0000000011421515
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF DIAGNOSTIC RESULT
With
CONSULT.
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result”.
Is DTC B02CB detected?
YES
>> Proceed to diagnosis procedure. Refer to
EXL-243, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011421516
1.
CHECK FRONT COMBINATION LAMP SHORT CIRCUIT TO GROUND
1. Disconnect front combination lamp connector and IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK FRONT COMBINATION LAMP SHORT CIRCUIT TO GROUND
1. Reconnect IPDM E/R connector.
2. Check continuity between fog lamp harness connector and ground.
Is the inspection result normal?
YES
>> Refer to
GI-44, "Intermittent Incident"
.
NO
>> Replace IPDM E/R. Refer to
PCS-40, "Removal and Installation"
.
DTC
Display Item
Malfunction detected condition
Possible causes
B02CB
DTRL LH PWR SPLY CIRC
[CIRC SHORT TO GRND]
When a short circuit to ground is detected.
• IPDM E/R
• Short to ground
IPDM E/R
Ground
Continuity
Connector
Terminal
E217
49
No
Front combination lamp
Ground
Continuity
Connector
Terminal
LH
E239
8
No
EXL-244
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
B20CE HEADLAMP (HI) LH POWER SUPPLY CIRCUIT
B20CE HEADLAMP (HI) LH POWER SUPPLY CIRCUIT
DTC Logic
INFOID:0000000011280875
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF DIAGNOSTIC RESULT
With
CONSULT.
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result”.
Is DTC B20CE detected?
YES
>> Proceed to diagnosis procedure. Refer to
EXL-244, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011280876
1.
CHECK HEAD LAMP SHORT CIRCUIT TO GROUND
1. Disconnect front combination lamp connector and IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK HEAD LAMP SHORT CIRCUIT TO GROUND
1. Reconnect IPDM E/R connector.
2. Check continuity between front combination lamp harness connector and ground.
Is the inspection result normal?
YES
>> Refer to
GI-44, "Intermittent Incident"
.
NO
>> Replace IPDM E/R. Refer to
PCS-40, "Removal and Installation"
DTC
Display Item
Malfunction detected condition
Possible causes
B20CE
DTRL LH PWR SPLY CIRC
[CIRC SHORT TO GRND]
Short to ground
• IPDM E/R
• Short to ground
IPDM E/R
Ground
Continuity
Connector
Terminal
E218
59
No
Front combination lamp
Ground
Continuity
Connector
Terminal
LH
E239
5
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст