Nissan Rogue. Instruction — part 588
HOW TO SELECT PISTON AND BEARING
EM-117
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
1. "Main Bearing Selection Table" rows correspond to bearing
housing grade on rear left side of cylinder block.
• If there is a corrected stamp mark on the cylinder block, use it
as a correct reference.
2. Apply journal diameter grade (A) stamped on crankshaft front
side to column in "Main Bearing Selection Table".
3. Find value at crossing of row and column in "Main Bearing Selection Table".
CAUTION:
• There are two main bearing selection tables. One is for odd-numbered journals (1, 3, and 5) and
the other is for even-numbered journals (2 and 4). Make certain to use the appropriate table. This
is due to differences in the specified clearances.
4. Apply the symbol obtained to "Main Bearing Grade Table" to select.
NOTE:
• Service parts are available as a set of both upper and lower.
When Cylinder Block and Crankshaft are Reused:
1. Measure inner diameter of cylinder block main bearing housing and outer diameter of crankshaft journal.
2. Apply measurement in above step 1 to the "Main Bearing Selection Table".
3. Follow steps 3 and 4 in "When New Cylinder Block and Crankshaft are Used".
SBIA0283E
(B) : Pin diameter grade
AWBIA0017ZZ
EM-118
< UNIT DISASSEMBLY AND ASSEMBLY >
HOW TO SELECT PISTON AND BEARING
Main Bearing Selection Table (No.1, 3, and No.5 journals)
KBIA0149E
HOW TO SELECT PISTON AND BEARING
EM-119
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Main Bearing Selection Table (No.2,and 4 journals)
Main Bearing Grade Table (All Journals) Refer to
Use Undersize Bearing Usage Guide
• Use undersize (U.S.) bearing when oil clearance with standard size main bearing is not within specification.
• When using undersize (U.S.) bearing, measure the bearing inner diameter with the bearing installed and
grind journal until oil clearance falls within specification.
Bearing Undersize Table
Unit: mm (in)
CAUTION:
Do not damage fillet R when grinding crankshaft journal in
order to use an undersize bearing (all journals).
KBIA0150E
Size U.S.
Thickness
0.25 (0.0098)
2.106 - 2.114 (0.0829 - 0.0832)
KBIA0148E
EM-120
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000011279984
GENERAL SPECIFICATIONS
Unit: degree
( ): Valve timing control “ON”
Drive belt
INFOID:0000000011279985
DRIVE BELT
Spark Plug
INFOID:0000000011279986
SPARK PLUG
Unit: mm (in)
Cylinder arrangement
In-line 4
Displacement
cm
3
(cu in)
2,488 (151.82)
Bore and stroke
mm (in)
89.0 x 100.0 (3.504 x 3.940)
Valve arrangement
DOHC
Firing order
1-3-4-2
Number of piston rings
Compression
2
Oil
1
Compression ratio
10.0
Compression pressure
kPa (kg/cm
2
, psi)/250 rpm
Standard
1,412 (14.4, 204.7)
Minimum
1,216 (12.4, 176.3)
Differential limit between cylinders
100 (1.0, 14.5)
Valve timing
: Intake valve
: Exhaust valve
a
b
c
d
e
f
224
244
8 (
−32)
ATDC
64 (24)
ABDC
8
36
PBIC5304E
Tension of drive belt
Belt tension is not necessary, as it is automatically adjusted by drive belt auto-tensioner.
Make
DENSO
Standard type
FXE20HE11C
Spark plug gap (Nominal)
1.1 (0.043)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст