Nissan Rogue. Instruction — part 140
BR-30
< REMOVAL AND INSTALLATION >
BRAKE MASTER CYLINDER
2. Tilt the reservoir tank so that the pin can be inserted. Insert a pin
using suitable tools.
JPFIA0303ZZ
BRAKE BOOSTER
BR-31
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
BRAKE BOOSTER
Exploded View
INFOID:0000000011279883
USA Production
Korea Production
Removal and installation
INFOID:0000000011279884
REMOVAL
1. Remove the instrument lower panel LH. Refer to
IP-23, "Removal and Installation"
.
2. Remove the knee protector. Refer to
.
ALFIA0487ZZ
1.
Brake booster
2.
Check valve
3.
Master cylinder
4.
Brake booster pressure sensor
5.
Gasket
6.
Clevis pin
7.
Spacer
Front
AWFIA1128ZZ
1.
Brake booster
2.
Check valve
3.
Master cylinder
4.
Brake booster pressure sensor
5.
Gasket
6.
Clevis pin
7.
Spacer
Front
BR-32
< REMOVAL AND INSTALLATION >
BRAKE BOOSTER
3. Remove the snap pin (1) and clevis pin (2) from the brake pedal.
4. Remove the cowl top and cowl top extension. Refer to
EXT-25, "Removal and Installation"
5. Disconnect vacuum hose from brake booster. Refer to
6. Remove master cylinder assembly. Refer to
BR-28, "Removal and Installation"
7. Disconnect the harness connector from the brake booster pressure sensor.
8. Remove the brake booster pressure sensor.
9. Remove the nuts on the brake booster and brake pedal.
CAUTION:
Secure the brake booster to avoid damage to components.
10. Remove the brake booster.
CAUTION:
Do not deform or bend the brake pipes.
INSTALLATION
1. Install a new gasket between the brake booster and dash panel.
CAUTION:
Do not reuse the gasket.
2. Install the brake booster to the dash panel from the engine room side.
CAUTION:
Do not damage brake booster stud bolt threads during installation.
3. Install the nuts to the brake booster and brake pedal. Refer to
4. Install the brake booster pressure sensor.
5. Connect the harness connector to the brake booster pressure sensor.
6. Install master cylinder assembly. Refer to
BR-28, "Removal and Installation"
.
7. Connect vacuum hose to brake booster. Refer to
8. Install the clevis pin and snap pin to the brake pedal.
9. Adjust the brake pedal. Refer to
.
10. Install the knee protector. Refer to
11. Install instrument lower panel LH. Refer to
IP-23, "Removal and Installation"
.
12. Bleed the brake system. Refer to
BR-16, "Bleeding Brake System"
13. Inspect the brake booster. Refer to
.
JPFIA0019ZZ
VACUUM LINES
BR-33
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
VACUUM LINES
Exploded View
INFOID:0000000011279885
Removal and Installation
INFOID:0000000011279886
REMOVAL
1. Remove the air duct assembly to the electric throttle control actuator. Refer to
2. Disconnect the vacuum hose from the engine intake manifold.
3. Disconnect the vacuum hose from the brake booster.
4. Disconnect the vacuum hose from the clip.
5. Remove the vacuum hoses.
INSPECTION AFTER REMOVAL
Visual Inspection
Check for correct installation, damage and deterioration of the vacuum hoses and pipe.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Insert the vacuum pipe into the vacuum hose at least 24 mm
(0.94 in) as shown.
• Do not use lubricating oil during installation.
1.
Clip
2.
Clamp
3.
Vacuum hose
4.
Vacuum tube
5.
Vacuum hose
A.
To intake manifold
B.
To brake booster
Front
ALFIA0488ZZ
SBR225B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст