Nissan Rogue. Instruction — part 562
PREPARATION
EM-13
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Anti-seize lubricant (Permatex 133AR
or equivalent meeting MIL specifica-
tion MIL-A-907)
Lubricating oxygen sensor thread cleaning
tool when reconditioning exhaust system
threads
KV10115600
(J-38958)
Valve oil seal drift
Installing valve oil seal
Use side A.
a: 20 (0.79) dia. d: 8 (0.31) dia.
b: 13 (0.51) dia. e: 10.7 (0.421) dia.
c: 10.3 (0.406) dia. f: 5 (0.20) dia.
Unit: mm (in)
Power tool
Loosening nuts, screws, and bolts
KV10107902
(J-38959)
Valve oil seal puller with adapter (1)
Removing valve oil seal
ST0501S000
Engine stand assembly
( — )
1. ST05011000
( — )
Engine stand
2. ST05012000
( — )
Base
Disassembling and assembling
KV10106500
( — )
Engine stand shaft
Engine supporting
Tool number
(TechMate No.)
Tool name
Description
AEM489
S-NT603
PIIB1407E
S-NT605
NT042
NT028
EM-14
< PREPARATION >
PREPARATION
KV10115300
( — )
Engine sub-attachment
Disassembling and assembling
(J-45816)
E20 Socket
Removing and installing CVT drive plate bolts
Tool number
(TechMate No.)
Tool name
Description
ZZA1078D
LBIA0285E
DRIVE BELTS
EM-15
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
PERIODIC MAINTENANCE
DRIVE BELTS
Exploded View
INFOID:0000000011279934
Checking
INFOID:0000000011279935
WARNING:
Inspect the drive belt only when the engine is stopped.
1. Visually check entire drive belt for wear, damage or cracks.
2. Check that the drive belt auto-tensioner indicator is within the possible use range.
NOTE:
• When new drive belt is installed, the drive belt auto-tensioner indicator should be within the new drive
belt range.
• Check the drive belt auto-tensioner indicator when the engine is cold.
3. If the drive belt auto-tensioner indicator is out of the possible use range or belt is damaged, replace drive
belt.
Tension Adjustment
INFOID:0000000011279936
Belt tension is not instructionly adjustable. It is automatically adjusted by the drive belt auto-tensioner.
Removal and Installation
INFOID:0000000011279937
REMOVAL
1. Remove wheel and tire (RH) using a power tool.
2. Remove engine under cover. Refer to
EXT-37, "ENGINE UNDER COVER : Removal and Installation"
3. Remove fender protector side cover. Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
1.
Generator pulley
2.
Water pump pulley
3.
Drive belt auto-tensioner
4.
Crankshaft pulley
5.
A/C compressor pulley
6.
Drive belt retainer boss
A.
View A
B.
New drive belt range
C.
Maximum belt length
D.
Indicator (notch)
AWBIA1893ZZ
EM-16
< PERIODIC MAINTENANCE >
DRIVE BELTS
4. Securely hold the hexagonal part (A) of drive belt auto-tensioner
(1) using suitable tool, and move in the direction of arrow (loos-
ening direction of tensioner).
5. Insert a rod approximately 6 mm (0.24 in) in diameter through
the rear of the drive belt auto-tensioner into retaining boss (B) to
lock drive belt auto-tensioner pulley.
WARNING:
Avoid placing hand in a location where pinching may occur
if the holding tool accidentally comes off.
NOTE:
Leave drive belt auto-tensioner pulley arm locked until drive belt
is installed again.
6. Loosen drive belt from drive belt auto-tensioner and then remove it from the other pulleys.
7. Installation of remaining components is in the reverse order of removal.
INSTALLATION
Installation is in the reverse order of removal.
1. Install the drive belt onto all of the pulleys except for the drive belt auto-tensioner. Then install the drive
belt onto drive belt auto-tensioner last.
CAUTION:
• Confirm belts are completely set on the pulleys.
• Check for engine oil and engine coolant. Be sure they are not adhered to the drive belt and each
pulley groove.
2. Release the drive belt auto-tensioner and apply tension to drive belt.
WARNING:
Avoid placing hand in a location where pinching may occur if the holding tool accidentally comes
off.
3. Turn crankshaft pulley clockwise several times to equalize tension between each pulley.
4. Confirm the indicator is within the possible use range. Refer to
5. Install wheel and tire (RH). Refer to
.
Removal and Installation of Drive Belt Auto-tensioner
INFOID:0000000011279938
REMOVAL
CAUTION:
The complete drive belt auto-tensioner must be replaced as a unit, including the pulley.
ALBIA0879GB
1.
Drive belt auto-tensioner
AWBIA1381ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст