Nissan Rogue. Instruction — part 732
REAR POWER WINDOW MOTOR
GW-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR POWER WINDOW MOTOR
Removal and Installation
INFOID:0000000011276520
REMOVAL
1. Remove rear door glass regulator. Refer to
GW-22, "Removal and Installation"
2. Remove screws (A) and rear door power window motor (1) from
rear door glass regulator (2).
INSTALLATION
Installation is in the reverse order of removal.
ALKIA3215ZZ
GW-26
< REMOVAL AND INSTALLATION >
QUARTER WINDOW GLASS
QUARTER WINDOW GLASS
Exploded View
INFOID:0000000011276521
Removal and Installation
INFOID:0000000011276522
REMOVAL
1. Remove the luggage side upper finisher. Refer to
INT-36, "LUGGAGE SIDE UPPER FINISHER :
.
2. Remove quarter glass from the inside of vehicle using a piano wire or cutting tool and an inflatable bag.
WARNING:
When cutting the quarter window from the vehicle, always wear safety glasses and heavy gloves
to help prevent glass splinters from entering your eyes or cutting your hands.
CAUTION:
• Apply protective tape around the quarter glass to protect the painted surface.
• Be careful not to scratch the quarter window glass when removing.
• Do not set or stand the quarter window glass on its edge. Small chips may develop into cracks.
1.
Quarter window glass
2.
Quarter window glass molding 3.
Body side outer
E.
7.0 mm (0.28 in)
F.
12.0 (0.47 in)
G.
Adhesive
Clip
AWBIA1977ZZ
QUARTER WINDOW GLASS
GW-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
INSTALLATION
Installation is in the reverse order of removal.
• Install the quarter glass from outside the vehicle to ensure that it is even around the top, bottom and sides of
the opening.
• Use a genuine NISSAN Urethane Adhesive Kit (if available) or equivalent and follow the instructions fur-
nished with it.
• While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced out
by passenger compartment air pressure when a door is closed.
• Check gap along bottom to confirm that glass does not contact sheet metal.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
• Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if inhaled.
If affected by vapor inhalation, immediately move to an area with fresh air.
• Driving the vehicle before the urethane adhesive has completely cured may affect the performance
of the glass in case of an accident.
CAUTION:
• Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date printed
on the box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Do not leave primers or adhesive cartridge unattended with their caps open or off.
• The vehicle should not be driven for at least 24 hours or until the urethane adhesive has completely
cured. Curing time varies depending on temperature and humidity. The curing time will increase
under lower temperatures and lower humidity.
Inspection
INFOID:0000000011276523
REPAIRING WATER LEAKAGE FOR QUARTER WINDOW GLASS
Leakage can be repaired without removing glass.
Determine the extent of leakage if water is leaking between the urethane adhesive material and body or glass.
This can be done by applying water to the side window glass area while pushing glass outward.
Apply primer (if necessary) and then urethane adhesive to the leakage point to stop the leakage.
GW-28
< REMOVAL AND INSTALLATION >
BACK DOOR WINDOW GLASS
BACK DOOR WINDOW GLASS
Exploded View
INFOID:0000000011276524
Removal and Installation
INFOID:0000000011276525
REMOVAL
1. Remove back door finisher. Refer to
INT-38, "Removal and Installation"
.
2. Remove the rear wiper arm and motor. Refer to
WW-73, "Removal and Installation"
3. Disconnect harness connectors from back door window defogger.
4. Remove back door window glass using piano wire or power cut-
ting tool and an inflatable pump bag.
WARNING:
When cutting back door window glass from vehicle, always
wear safety glasses and heavy gloves to prevent glass
splinters from entering your eyes or cutting your hands.
CAUTION:
• Be careful not to scratch glass when removing.
• Do not set or stand glass on its edge. Small chips may
develop into cracks.
• Apply protective tape around back door window glass to
protect painted surface from damage.
NOTE:
Mark body and glass with matching marks if back door window glass is to be reused.
INSTALLATION
Installation is in the reverse order of removal.
• Use genuine NISSAN Urethane Adhesive Kit (if available) or equivalent and follow the instructions furnished
with it.
• Adhesive shall be continuously applied to assure watertightness. Glass installation shall be finished within
five minutes after applying adhesive.
• While urethane adhesive is curing, open door window. This will prevent glass from being forced out by pas-
senger compartment air pressure when door is closed.
• Start and finish urethane adhesive application at the bottom to assure watertightness.
• Inform customer that vehicle should remain stationary until urethane adhesive has completely cured (prefer-
ably 24 hours). Curing time varies with temperature and humidity.
WARNING:
1.
Back door window glass
A.
Clip
Clip
AWKIA3178ZZ
SBF034B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст