Nissan Rogue. Instruction — part 1268
REAR WASHER NOZZLE AND TUBE
WW-75
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
2. Release pawls and remove rear washer nozzle (1).
: Pawl
INSTALLATION
Installation in the reverse order of removal.
Removal and Installation - Rear Washer Tube
INFOID:0000000011280436
REMOVAL
1. Remove front over fender (RH). Refer to
EXT-30, "FRONT OVER FENDER : Removal and Installation"
.
2. Remove wind deflector (RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
3. Remove engine side cover (RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
4. Partially remove front fender protector (RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
5. Release seat latches by pulling straps (A) rearward, then lift seat
from seat strikers (LH/RH).
6. Remove dash side finisher (RH). Refer to
INT-24, "DASH SIDE FINISHER : Removal and Installation"
.
7. Remove center pillar lower finisher (RH). Refer to
INT-22, "CENTER PILLAR LOWER FINISHER :
.
8. Remove luggage side upper finisher (LH/RH). Refer to
INT-36, "LUGGAGE SIDE UPPER FINISHER :
.
9. Remove headlining clips (A) using suitable tool (B) and partially
lower headlining (rear).
10. Disconnect rear washer tube from washer tank and rear washer nozzle.
11. Release clips and remove rear washer tube.
INSTALLATION
Installation is in the reverse order of removal.
AWLIA2307ZZ
ALJIA1425ZZ
ALLIA1604ZZ
WW-76
< REMOVAL AND INSTALLATION >
REAR WASHER NOZZLE AND TUBE
Inspection and Adjustment
INFOID:0000000011280437
INSPECTION
Check that air can pass through the nozzle by blowing into the noz-
zle and that air cannot flow in the opposite direction.
O: Air can go
X: Air cannot go
ADJUSTMENT
If operating properly, spray positions should match the positions shown. If spray positions do not match, con-
firm the rear washer nozzle is properly seated and working properly. If the spray positions still do not match as
shown, then replace the rear washer nozzle. Refer to
WW-74, "Removal and Installation - Rear Washer Noz-
JMLIA1675ZZ
1.
Black print
2.
Wiping area
A. Spray target area
B. 12.8 mm (0.5 in)
C. 12.8 mm (0.5 in)
D. 25.7 mm (1.0 in)
E. 15.5 mm (0.6 in)
F.
20.6 mm (0.8 in)
AWLIA2309ZZ
FRONT WIPER DRIVE ASSEMBLY
WW-77
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
FRONT WIPER DRIVE ASSEMBLY
Exploded View
INFOID:0000000011394503
DISASSEMBLY VIEW
Disassembly and Assembly
INFOID:0000000011394560
DISASSEMBLY
1. Remove front wiper motor. Refer to
WW-69, "Removal and Installation"
2. Remove front wiper linkage 1 and 2 from the front wiper drive.
CAUTION:
Do not bend the linkage or damage the plastic part of the ball joint when removing the front wiper
linkage.
ASSEMBLY
1. Install front wiper motor to front wiper drive.
2. Install front wiper linkage 1 to the front wiper motor and the front wiper drive.
3. Install front wiper linkage 2 to the front wiper drive.
CAUTION:
• Do not drop front wiper motor or cause it to come into contact with other parts.
• Apply multi
−purpose grease or an equivalent grease if necessary.
1. Front wiper linkage 1
2.
Front wiper linkage 2
3.
Front wiper drive
4. Front wiper motor
ALLIA1613ZZ
WW-78
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Specifications
INFOID:0000000011280438
WINDSHIELD WASHER FLUID
Windshield washer fluid capacity (with washer tank inlet)
5.2 (5 1/2 US qt, 4 5/8 Imp qt)
Windshield washer fluid specification
Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст