Nissan Rogue. Instruction — part 200
CHG-18
< DTC/CIRCUIT DIAGNOSIS >
B TERMINAL CIRCUIT
B TERMINAL CIRCUIT
Description
INFOID:0000000011278228
“B” terminal circuit supplies power to charge the battery and to operate the vehicles electrical system.
Diagnosis Procedure
INFOID:0000000011278229
Regarding Wiring Diagram information. Refer to
.
1.
CHECK “B” TERMINAL CONNECTION
1. Turn ignition switch OFF.
2. Check if “B” terminal is clean and tight.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair terminal “B” connection. Confirm repair by performing complete Charging system test
using the EXP-800 NI or GR8-1200 NI (if available). Refer to applicable Instruction Instruction for
proper testing procedures.
2.
CHECK “B” TERMINAL CIRCUIT
Check voltage between generator “B” terminal and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check harness for open between generator and fusible link.
3.
CHECK “B” TERMINAL CONNECTION (VOLTAGE DROP TEST)
1. Start engine, then engine running at idle and warm.
2. Check voltage between battery positive terminal and generator connector “B” terminal.
Is the inspection result normal?
YES
>> “B” terminal circuit is normal. Refer to
CHG-11, "Work Flow (With EXP-800 NI or GR8-1200 NI)"
CHG-14, "Work Flow (Without EXP-800 NI or GR8-1200 NI)"
.
NO
>> Check harness between battery and generator for continuity.
(+)
(-)
Voltage
(Approx.)
Generator
Connector
Terminal
F29
1
Ground
Battery voltage
(+)
(-)
Voltage
(Approx.)
Generator
Connector
Terminal
F29
1
Battery positive terminal
Less than 0.2V
CHG
CHARGING SYSTEM
CHG-19
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SYMPTOM DIAGNOSIS
CHARGING SYSTEM
Symptom Table
INFOID:0000000011278230
Symptom
Reference
Battery discharged
CHG-11, "Work Flow (With EXP-800 NI or GR8-1200 NI)"
or
CHG-14, "Work Flow (Without EXP-800 NI or GR8-1200 NI)"
The charge warning lamp does not illuminate when the ignition
switch is set to ON.
The charge warning lamp does not turn OFF after the engine
starts.
The charging warning lamp turns ON when increasing the engine
speed.
CHG-20
< REMOVAL AND INSTALLATION >
GENERATOR
REMOVAL AND INSTALLATION
GENERATOR
Exploded View
INFOID:0000000011278231
REMOVAL
Removal and Installation
INFOID:0000000011278232
REMOVAL
1. Disconnect negative terminal from battery. Refer to
.
2. Remove front air spoiler. Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
3. Remove drive belt. Refer to
EM-15, "Removal and Installation"
.
4. Remove oil level gauge (1).
5. Remove oil level gauge guide (2).
6. Remove oil level gauge guide O-ring (3).
1.
Generator bracket
2.
"B" terminal harness
3.
Generator
A.
Refer to INSTALLATION
B.
Refer to INSTALLATION
Front
AWMIA1611ZZ
AWMIA1613ZZ
CHG
GENERATOR
CHG-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
7. Disconnect harness connector (A) from the generator.
8. Remove “B” terminal nut (B) and “B” terminal harness.
9. Remove harness bracket (C).
NOTE:
Harness ground does not have to be removed during bracket
removal.
10. Remove upper generator mounting bolt (D), using suitable tool.
11. Remove lower generator mounting bolt (E), using suitable tool.
12. Remove generator upward from the vehicle.
13. Remove generator bracket (if necessary).
INSTALLATION
1. Install generator bracket and tighten bolts in the numerical order
as shown.
2. Install generator and temporarily tighten bolts in the reverse
numerical order as shown.
3. Tighten generator bolts in the numerical order as shown.
4. Installation of remaining components is in the reverse order of removal.
NOTE:
Tighten oil level gauge guide bolt to specification. Refer to
.
CAUTION:
• Be careful to tighten “B” terminal nut carefully.
• Install generator and check tension of belt. Refer to
.
• Do not reuse oil level gauge guide O-ring.
• Prior to installation, apply clean engine oil to oil level gauge guide O-ring.
• Ensure O-ring sealing surface is free from dust or imprefections.
• Allow engine to run for 5 minutes and inspect for engine oil leaks.
Inspection
INFOID:0000000011278233
GENERATOR PULLEY INSPECTION
Perform the following.
• Make sure that the generator pulley does not bind or rattle.
• Make sure that the generator pulley is tight. Refer to
AWBIA1830ZZ
JPMIA0752ZZ
Bolts
: 64.7 N·m (6.6 kg-m, 48 ft-lb)
ALMIA0735ZZ
Bolts
: 25 N·m (2.6 kg-m, 18 ft-lb)
ALMIA0736ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст